IPOX SW8-TX User manual

Please check the following items before installation, if it is missing, please contact the dealer .
8 ports Ethernet Switch 1pcs
Power adaptor 1pcs
Accessory 1pcs
User manual 1pcs
1) Please turn off the signal power and display device power before installation,
installation with power will damage the transmission equipment;
2) Use network cable connect IP camera and 1～8 down link ports of product respectively;
3) Use a network cable connect switch's up link port with NVR or computer;
4) Connect power adapter;
5) Check if the installation is correct, equipment is in good condition, the connection is
stable, then provide power for system;
6) Ensure the Ethernet equipment with power and work properly.
Installation steps
Feature
8 Ports Ethernet Switch
8 Ports Ethernet Switch
User Manual
12
8 ports Ethernet Switch is a surveillance Ethernet switch which aims at Ethernet high
definition surveillance and Ethernet project security system. The product fully combines the
characteristics of security surveillance, provides fast packet forwarding ability and abundant
backplane bandwidth, which ensures clear image and fluent transmission. ESD and surge
protection circuit can improve product stability. The product supports one key CCTV mode,
can achieve VLAN, control the Net storm, protect the information security, prevent the viral
transmission and Ethernet attack, fully satisfy the Ethernet video security surveillance system
and Ethernet project needs.
security
Board Diagram
Front board
VerB 1.2
● Major ports: 1pcs 100Mbps up link Ethernet port, 8pcs 100Mbps downlink Ethernet
ports , each port supports MDI/MDIX;
● Special function: One key CCTV mode;1～8 downlink ports can only communicate with
uplink ports;
● Power input: DC12V;
● Transmission Distance: 0～100m; the farthest transmission distance could reach 250m in
CCTV model; Uplink port can reach 100m;
● Standard: Meet IEEE802.3, IEEE802.3u standards;
● Protection: Excellent anti-thunder, anti-static and anti-interference ability;
● Appearance: Delicate design and easy installation, configure the anti-theft lock hole,
guard against theft;
●Operation: Plug and Play, No Setting required.
Back board
Side board
Notice
The transmission distance is related to the connected cable. We suggest standard Cat5e/6
network cable, so the transmission distance can up to furthest distance!
1)
level will reduce; please use above No.20 wire to connect the grounding terminal.
2) Turn the dial switch for left, the equipment can enter surveillance module after power on.
Device must be connected with lightning protection grounding; otherwise protection
Power
indicated light
Surveillance module
indicated light
normally on
Kensington lock
Application
Please follow below the installation steps
Downlink
Ethernet port Uplink
Ethernet port
Ground
Power
input port
5-12VD C
8 Port Switch
Cat5/5e/6
PTZ Camera
Dome Camera
IP Camera
Power
IP Camera
Power
Power Power
Power
Power
LCD
NVR
IP Camera
Notice

连接接 口
Specification 连接接 口
8 Ports Ethernet Switch
3
4
Specification change will not be noticed
8 Ports Ethernet Switch
连接接 口
连接接 口
Trouble Shooting
Please follow the steps if the equipment has trouble.
Make sure the equipment is installed according to the manufactures installation guide.
Confirm RJ45 cable order meets EIA/TIA568A or 568B standard.
Replace the equipment that can not work with a good one to check if the equipment is
damaged.
Please contact your vendor if trouble still exists.
Instruments to be used: wire crimper, network tester. Wire sequence of RJ45 plug should
conform with EIA/TIA568A or 568B.
1) Please remove 2cm long the insulating layer, and bare 4 pairs UTP cable;
2) Separate the 4 pairs UTP cable and straighten them;
3) Line up the 8 pieces of cables per EIA/TIA 568A or 568B;
4) Cut off the cables to leave 1.5cm bare wire;
5) Plug 8 cables into RJ45 plug, make sure each cable is in each pin;
6) Use the wire crimper to crimp it;
7) Repeat above 5 steps to make the another end;
8) Using network tester to test the cable if it works.
Plug Producing Method
Pin Color
White/Green
Green
Blue
White/Orange
White/Blue
White/Brown
Orange
Brown
1
2
3
4
5
6
7
8
Pin Color
1
2
3
4
5
6
7
8
White/Green
Green
Blue
White/Orange
White/Blue
White/Brown
Orange
Brown
EIA /TIA 56 8 A EIA /TIA 56 8 B
When choose RJ45 make sure if one end is EIA/TIA568A,the other end should also be EIA/TIA568A.
When choose RJ45 make sure if one end is EIA/TIA568B,the other end should also be EIA/TIA568B.
Notice
Item
Description
Power
Power Supply
Power Adaptor
Voltage Range
DC5V~12V
Consumption
＜5W
Ethernet
Speed
1～8 port:Default:10/100Mbps;
CCTV:10Mbps;
UPLINK:10/100Mbps
Transmission Distance
1-8 port:Default:0～100m;
CCTV:0~250;
UPLINK:0～100m
Network
Switch
Ethenet Standard
IEEE 802.3/802.3u
Backplane Bandwidth
1.8G
Packet Forwarding Rate
1.34Mbps
Packet Buffer
768K
MAC
2K
Status
Indicator
Power Light
1pcs Red( )
Ethernet Port Light
2pcs(Yellow&Green) on RJ45,yellow off, green indicates
/actLink
Surveillance Module Light
1pcs(Green), On indicates CCTV
Protection
Level
Pluse Group
Level 2
Standard: IEC61000-4-4
ESD
1a Contact Discharge Level 3
1b Air Discharge Level 3
Standard: IEC61000-4-2
Anti-thunder Level
Level
Standard: IEC61000-4-5
3
Working
Environment
Working Temperature
0 ~55℃℃
Storage Temperature
-40 ~85℃℃
Humidity(Non-condesing)
0~95%
Mechanical
Dimension(L*W*H)
200mm×101.8mm×27mm
Out Shell
Galvanized Sheet
Color
Black
Weight
490g
3