Iqinvision Alliance-mx User manual

1
IQeye Alliance-mx
Vandal-Resistant IP Camera
Installation and Operating Instructions

2
Contents
1 Unpacking 3
2 Service 3
3 Description 4
4 Installation 4
5 Parts List 4
6 Mounting Options 5
7 Removal of Dome Cover 6
8 Mounting the Enclosure, Camera, and Lens Assembly 6
9 Connect Camera 8
10 Camera Positioning, Field-of-View Set-up and Focus 8
11 Factory Reset 9
12 Complete the Dome Camera Installation 9
13 PC Configuration of Alliance-mx 9

3
1 Unpacking
Unpack carefully. This is an electromechanical device and should be
handled carefully. Check to ensure the following items are included:
> Alliance-mx Dome Camera Assembly
> Torx T-20 Security Wrench
> ½” NPT Plug (installed in the side NPT mount of the enclosure)
> Mounting Hardware
> Mounting Template
> IQtools CD-ROM
2 Service
If the unit needs repair service or parts, the customer should contact
IQinVision for authorization to return, as well as shipping instructions.
IQinVision
33122 Valle Road
San Juan Capistrano, CA 92675-4853
Phone: [phone] or 1-877-850-0805 (toll-free in U.S.)
Fax: [phone]

4
3 Description
The Alliance-mx H.264 Standard and High Definition dome cameras
provide exceptional image quality in the most demanding indoor /
outdoor environments. Available in HD1080p, HD720p, and SD480p
resolutions, the Alliance-mx uses Main Profile H.264 to deliver
exceptional high-definition clarity at up to 30 frames-per-second.
Simultaneous H.264 and MJPEG video streaming offers flexibility to
optimize live viewing and recording while providing access to video for
other applications.
Alliance-mx camera automatically senses low light levels and
switches from color to monochrome maintaining coverage in the
most challenging lighting conditions. Made from cast aluminum and
polycarbonate bubble the Alliance-mx is IP66 (NEMA 4) rated. The
included 3-13mm varifocal lens offers flexibility so the Alliance-mx
camera can be installed almost anywhere.
4 Installation
NOTE: This manual describes how to install the IQeye Alliance-mx camera system, and details interior /
exterior wall and ceiling surface mounting options. Installations should be performed by qualified service
personnel only in accordance with local and national code(s).
5 Parts List
The following depicts the parts included (Figure 5.1):
1. Alliance-mx Enclosure, Camera, and Lens Assembly
2. Alliance Dome Cover, and Shroud Assembly
Figure 5.1

5
6 Mounting Options
The Alliance-mx camera is designed to be used in one of the following
configurations.
1. Surface mounted to a plenum or other durable ceiling surface.
2. Surface mounted to any interior / exterior durable wall surface.
3. Mounted to the optional interior / exterior wall mount adapter.
NOTE: This guide covers installation of an Alliance-mx dome camera without the optional wall mount
adapter. For guidance on mounting the Alliance-mx to the wall mount adapter, consult the wall mount
adapter manual.
WARNING: When installing the Alliance-mx dome camera outdoors, the camera should not
be mounted directly to a wall surface. When mounting outdoors to a wall surface, the IQM-
WM2 (Alliance Wall Mount) is required (Figure 6.1).
Alliance-mx cameras provide the following connection options shown in
(Figure 6.2).
1. Ethernet (Power-over-Ethernet) connector.
2. Audio in/out connector (Requires optional audio cable with 3.5 mm audio
connectors).
Ethernet (Power-over-Ethernet) Connector
Audio In/Out Connector
Figure 6.2
Figure 6.1

6
7 Removal of Dome Cover
1. Using the supplied Torx T-20 security wrench, loosen the three tamper-proof
screws holding the dome cover to the enclosure assembly (Figure 7.1).
Note that these screws are captive, and held to the dome cover. These screws
should not be removed from the dome cover trim ring.
2. Lift the dome trim ring with shroud away from the camera assembly.
8 Mounting the Enclosure, Camera, and Lens Assembly
Mounting to masonry or other durable surface wall, ceiling or overhang
with cables routing through the wall or ceiling.
1. Position the supplied mounting template on the surface in the location where
the camera will be installed. Trace and drill the mounting holes and the cable
pass through hole as indicated.
2. Route the network cable through the wall.
3. Gently push the Ethernet cable through the gasket
installed in the enclosure. Pull enough cable through the gasket to attach an
RJ-45 network connector, and to allow the network connector to plug into the
Ethernet socket
(Figure 8.1).
It may be necessary to pierce a hole in the gasket with an Awl tool (not supplied).
NOTE:
• Do not cut the gasket with a knife.
• Do not force the Ethernet cable with connector
through the gasket.
• Only pass one cable through the supplied gasket.
Figure 8.1
Figure7.1
Figure 8.2

7
4. To ensure the gasket is sealed gently pull back on the Ethernet cable as shown
in Figure 8.3 before mounting the enclosure to the wall or ceiling.
5. Attach the enclosure to the wall or ceiling by tightening the four screws with
sealing washers (Figure 8.4).
NOTE: Be sure to use the supplied screws and sealing washers. Alternative washers will not seal the
enclosure from moisture. Extra sealing washers are supplied.
Mounting to masonry or other durable surface wall, ceiling or overhang with
cables routing along the wall or ceiling for side conduit installation.
1. Position the supplied mounting template on the surface in the location where
the camera will be installed. Trace and drill the mounting holes and the cable
pass through hole as indicated.
2. Remove the conduit plug from the enclosure. Install a ½” (12.7mm) threaded
conduit connector (not supplied) into the conduit hole on the enclosure.
NOTE: To ensure proper weatherization on the conduit entry, properly seal the conduit threads with silicon.
3. Pull the Ethernet cable through the conduit and then through the enclosure.
Pull enough cable through the conduit to attach an RJ-45 network connector,
and to allow the network connector to plug into the Ethernet socket.
4. Attach the enclosure to the wall or ceiling by tightening the four screws with
sealing washers.
NOTE: Be sure to use the supplied screws and sealing washers. Alternative washers will not seal the
enclosure from moisture. Extra sealing washers are supplied.
NOTE: When installing the Alliance-mx onto a ceiling tile, use hardware designed to secure the camera
assembly to this surface, and ensure the ceiling tile material is secure.
In addition, follow local regulations and laws that may have specific requirements
governing the installation of security equipment on a ceiling tile surface.
IQinVision also strongly recommends the use of a ceiling tile brace and other
mounting hardware designed to secure the Alliance-mx to the ceiling frame
infrastructure.
Figure 8.3 Figure 8.4

8
9 Connect Camera
1. For the Alliance-mx IQM30 & IQM31 series cameras,
route and connect the Power-over-Ethernet cable to
the Ethernet connector port in the camera as shown
in Figure 9.1.
For the Alliance-mx IQM32 series cameras attach
the supplied ferrite clamp to the Ethernet cable, and
connect the cable to the Ethernet connector port in
the camera as shown in Figure 9.2.
2. Route and connect the optional (not supplied) audio
cable when using an external microphone and
powered loudspeaker (not supplied) to the Alliance-mx
dome camera as shown in Figure 9.3.
The external microphone and powered loud-
speaker (not supplied) will connect to 3.5 mm
audio connectors.
10 Camera Positioning, Field-of-View Set-up and Focus
1. Set the field-of-view using the 3-axis gimbal. Determine camera pan direction
by gripping the camera assembly, and carefully pivot the camera to the viewing
direction.
2. Adjust the tilt of the camera by loosening the tilt angle lock screws as shown in
Figure 10.1, and tilt the camera to the viewing direction. When finished, tighten
the tilt locking screws.
3. Adjust the field-of-view and focus rings to achieve the desired focus as shown
in Figure 10.2.
NOTE: The lens on the Alliance-mx dome camera is fixed iris and therefore no iris adjustment
is needed.
When finished, tighten the thumbscrews on the lens.
Figure 9.1
Figure 10.1 Figure 10.2
Figure 9.2
Optional Audio
In/Out Cable
Assembly
Audio cable can
Only Pass Through
the Conduit Entry
Focus Control
Zoom Control
Figure 9.3

9
11 Factory Reset
1. Press and hold the “Reset” button for 10 seconds as illustrated in Figure 11.1.
12 Complete the Dome Camera Installation
1. Attach the tether from the dome trim ring to the tether mounting point in the
enclosure as shown in Figure 12.1.
2. Rotate the black shroud inside the dome trim ring cover so it aligns with the
camera position.
3. Place the supplied desiccant pack inside the dome as shown in Figure 12.2 to
prevent fogging due to moisture that is present when installing the camera.
Use the supplied cable tie to keep the desiccant from falling down into the
dome bubble.
4. Attach the dome trim ring cover with shroud to the enclosure by tightening the
three tamper-proof screws with the supplied Torx T-20 security wrench.
13 PC Configuration of Alliance-mx
NOTE: The default user name for all IQeye devices is “root” and the default password is “system”.
IQeye cameras are configured for DHCP and will have an IP address assigned if
a DHCP server is on the network. If a DHCP server is not available, the camera
IP address will need to be configured using either IQfinder or IQmanager
depending on the number of cameras being installed.
Figure 11.1
Figure 12.1 Figure 12.2

10
1. Insert the IQtools CD into the CD drive of the PC. Once the CD starts, run
IQfinder either from the CD by clicking “Scan for IQeye cameras on my
network” or by installing IQfinder on the local machine by selecting “Install
IQfinder”.
2. Click “Scan for IQeye cameras on my network” to find IQeye cameras (Figure
13.1). The detected cameras will be displayed in
the IQfinder window. Select a camera from the list
and click “Assign IP” to edit the selected camera’s
network settings.
3. The “Assign IP” window allows the IP address,
Subnet, and Gateway of the camera to be changed
and alternatively the camera to be configured for
DHCP operation. Click the ”Apply” button after
making the desired changes (Figure 13.2).
NOTE: Changing between a static IP address and DHCP will cause the
camera to reboot.
4. To view a camera, double click a camera entry or
highlight a camera in the list and click the “Web Page”
button (Figure 13.3). The “Live” page will be displayed
through the default browser (IE recommended). It is
also possible to open Internet Explorer and enter the IP
address of the IQeye camera
in the address field of the browser. If prompted, install
the Active X control (Figure 13.4).
5. To perform further configuration of the camera
click on the “Setup” tab.
NOTE: The default username is “root” and the default password is
“system”.
6. To prepare the camera to serve the H.264 stream
(Alliance-mx), select H.264 from the video format
drop-down (Figure 13.5). To view the H.264 stream full
screen (without “Live” page controls), double
click on the video area. Double click on the video
image again to return back to the “Live” page.
7. For additional information and technical
documents, please visit www.IQeye.com.
Figure 13.1
Figure 13.2
Figure 13.3
Figure 13.4
Figure 13.4

11
For product warranty, additional documentation and technical information,
please visit www.iqeye.com/support

12
33122 Valle Road San Juan Capistrano, CA 92675-4853 USA |phone [phone] |fax [phone] |www.iqeye.com
901-0243 Rev F