Iris Innovations IRISx460 User manual

Iris Innovations
IRISx460 User Guide v2.3 April 2021
1
IRISx460
QUICK-START GUIDE

Iris Innovations
Regulatory Information
Disposal of Waste Equipment by Users in Private Household in the European Union.
This symbol on the product or its packaging indicates that it must not be disposed of with
your other household waste. Instead, it is your responsibility to dispose of your waste
equipment by handing it over to a designated collection point for the recycling of waste
electrical and electronic equipment. The separate collection and recycling of your waste
equipment at the time of disposal will help to conserve natural resources and ensure that
it is recycled in a manner that protects human health and the environment. For more
information about where you can drop off your waste equipment for recycling please
contact your local city office, your household waste disposal service or the shop where
you purchased the product.
This device has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio or
television reception. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause interference to radio and television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorientate or relocate the receiving antenna; Increase the separation between the
equipment and the receiver, connect the equipment to an outlet on a different circuit from
that to which the receiver is connected; consult the dealer or an experienced radio / TV
technician for help.
We hereby declare that the product is in compliance with the essential requirements
and other relevant provisions of EMC Directive 2014/30/EC, the RoHS Directive
2011/65/EU.
IRISx460 User Guide v2.3 April 2021
2
!
!
!

Iris Innovations
IRIS460 User Guide
(C) 2021 Iris Innovations Limited.
ALL RIGHTS RESERVED
Any and all information, including, among others, wordings, pictures, graphs are the properties of IRIS
INNOVATIONS., Ltd. or its subsidiaries (hereinafter referred to be “IRIS”). This user manual (hereinafter
referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by
any means, without the prior written permission of IRIS. Unless otherwise stipulated, IRIS does not make any
warranties, guarantees or representations, express or implied, regarding to the Manual.
LEGAL DISCLAIMER
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS
HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS,
AND IRIS MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-
INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL IRIS, ITS DIRECTORS, OFFICERS,
EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL,
OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS
PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION
WITH THE USE OF THIS PRODUCT, EVEN IF IRIS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE
WHOLLY AT YOUR OWN RISKS. IRIS SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL
OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER
ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, IRIS WILL
PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE
CONFORMS THE APPLICABLE LAW. IRIS SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT
IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER
PREVAILS.!
IRISx460 User Guide v2.3 April 2021
3

Iris Innovations
Warnings & Important Product
Information
WARNING: Installation and Operation
This product must be installed and operated in accordance with
these instructions. Failure to do so may result in poor product
performance, damage to the product or vessel and or personal
injury. Installation should only be carried out be qualified
personnel or by persons competent in electrical systems.
WARNING: Power Supply and Grounding
Ensure the boats power supply is switched off during installation.
Ensure suitably rated circuit breakers / fuses are used in the
installation of the product in accordance with the electrical
values shown in the technical specifications of the product.
Never switch on power until the power connections are correctly
terminated in accordance with the information provided in this
document. Do not connect or disconnect the product with the
power supply switched on. Never disconnect the DC ground with
the power supply on.
WARNING: Wiring terminations
Where the products video, power and data terminations are
extended, ensure that suitable connectors are used and that the
point of termination for each cable is adequately protected
against moisture ingress. Ensure correct polarity is strictly
observed. Do not cut or remove cable connectors without prior
permission from Iris Innovations Limited.
WARNING: Do Not Open the Unit
There are no user serviceable parts within the product so there s
no need to open the device. The product has been certified to
IP66 standards, however, submersion or the product or
exposure to high pressure washing will invalidate the warranty.
WARNING: Disclaimer
This product is intended to be used only as an aid to navigation
and must never be used as an alternative to correct navigational
practices and judgements made on the basis of approved
navigation methods. It is the users responsibility to observe
correct and proper navigational skill when using this product.
Only officially approved charts and notices to mariners contain
the current information required for safe navigation.
Operating the camera or viewing the video input whilst the
vessel is moving could cause a distraction and result in
accidental collision resulting in property damage, injury or death.
Iris Innovations cannot be held liable for any incidental, special,
indirect or consequential damages whether resulting from the
use, misuse or inability to use this product.
CAUTION: Switch Camera Off When Not in Use.
To prolong the operation life of the the cameras sensor we
strongly advise that power to the camera is routed via a
dedicated switch.
CAUTION: Service and Maintenance
This product contains no user serviceable parts. Please refer all
maintenance and repair issues to your authorised Iris
Innovations dealer. Any unauthorised work to the product may
affect the warranty.
CAUTION: Care and Cleaning
This product is a sensitive piece of electronic, imaging
equipment and must be handled and treated accordingly. Do not
drop or shake the unit during installation. Avoid exposure of the
imager to direct sunlight where possible as this may degrade the
cameras performance over time.
When cleaning the device, ensure power is switched off. Clean
the camera housing with a soft cloth. Moisten the cloth and use
a mild detergent if required. The lens window has a protective
coating which may suffer damage as a result of improper
cleaning. To clean the lens window use a soft cotton cloth.
Moisten with clean water if necessary. For further advise on
cleaning the lens window, contact Iris Innovations.
INFORMATION: Product Disposal and Recycling
Dispose of this product in accordance with the WEEE Directive.
The Waste Electrical and Electronic Equipment (WEEE)
Directive requires the recycling of waste electronic and electrical
equipment. Iris Innovations supports the WEEE policy and
politely request you observe correct disposal methods. For
further information on how to correctly dispose of this product
please contact Iris Innovations.
Please recycle unwanted packaging and documentation. The
cardboard carton, all paper manuals and documents and the
protective plastic bag in which the camera is shipped are widely
recyclable. Please check with your local recycling plant for
confirmation.
EMC Guidelines
This camera is designed to be used as a visual aid and is not
part of the vessels navigational system - even if used in
conjunction with other on board equipment or third party
systems - and is compliant with the EMC directive 2014/30/EC.
The original Declaration of Conformity (DoC) is available from
our website
The camera should not be installed on the ships helm or in close
proximity to radio receiver equipment. We recommend the
camera is installed no closer than 1m from any equipment
transmitting or cables carrying radio signals - particularly VHF
radios and associated equipment.
The camera should be powered from a clean 12VDC supply. If
when powered via a Power over Ethernet (PoE) connection any
interference occurs on either the camera or nearby equipment,
the effected equipment should be separated by a greater
distance.
Water Ingress: Disclaimer
This product has been tested and complies with the
requirements of the standard EN60529 to level IPx6, however,
water intrusion and subsequent equipment failure may occur is
subject to commercial high pressure washing or sustained
exposure to water spray. This product is not designed to be
submerged. Any damage caused as a result of these
circumstances are not covered by the product warranty.
NOTE:
Due to manufacturing techniques there may be minor variations
in the form of the stainless steel cowling. This is expected and
does not detract from the performance and overall aesthetic of
the product.!
IRISx460 User Guide v2.3 April 2021
4

Iris Innovations
Introduction
Thanks for buying the IRISx460 Miniature IP Dome Camera
from Iris Innovations.
The IRISx460 is an IP version of our best selling IRIS06x range
of dome cameras, made successful due to its stylish, miniature
design and quality reliable performance.
The camera is also available with a marine grade 316L Stainless
Steel case. Stainless cameras have the model number IRIS-
S460.
By using IP cameras, installation and cabling costs are reduced,
video and control can be networked easily around your vessel,
and you can even view and control your cameras from your
smart phone, tablet or computer wirelessly. By hooking your new
IRISx460 camera into your onboard network and connecting that
in turn to a WAN using a cellular, satellite, wired or WiFi
connection, you can also view and control the cameras when
you are at home or in the office!
The IRISx460 camera is an extremely versatile device. It is
widely used to monitor decks, companionways, engine rooms,
as a back up camera and as a docking camera.
The IRISx460 is an ONVIF compliant device which means it can
be viewed on any ONVIF hardware, including DVR’s, computers
and compatible MFD’s such as Raymarine’s Axiom, Navico
devices such as Simrad NSS range and other network plotters.
For compatibility information please contact your Iris dealer or
visit www.boat-cameras.com!
Overview of Key Features
Here’s a brief list of some of the IRIS460’s key features:
•Up to 3MP Resolution (2304 x 1296)
•High Performance LED’s - 10 Meter Range
•Mechanical IR Cutout filter for True Day / Night Operation
•Low Power 12VDC Operation <150mA
•IEEE802.3af Power over Ethernet (PoE)
•Various Lens Options (3.6mm / 2.8mm / 1.8mm)
•IP66 Ingress Protection
•Small, Compact Housing
•Marine Grade 316 Stainless Steel Housing (IRIS-S460
models)
•Suitable for Multiple Applications, such as on-board security,
sports fishing, engine room monitoring and vehicle monitoring
•Wide Operating Temperature Range
•Compatible with ONVIF compliant Chart Plotters such as the
Raymarine Axiom and all other Raymarine network MFD’s
running Lighthouse II & III software, Furuno Timezero 4.1
Software (PC version), Navico NEON, NOS operating
systems.
Contents of Package
Please unpack your IRIS460 and check to make sure the
following items are included. If there are any items missing
please contact your Iris dealer:
•1 x IRIS460 Marine Mini Dome Camera
•1 x Fixing Pack
•1 x Instruction Manual
•1 x Water Resistant RJ45 connector kit
•1 x Foam Mounting Pad
•1 x Self Adhesive Fixing Template!
IRISx460 User Guide v2.3 April 2021
5

Iris Innovations
Camera Overview
The diagram below details the various parts of your
camera:
Warning!
Camera Installation Sequence
The diagram below shows the sequence in which the
camera parts are fit into place during installation...
Warning!
It is strongly advised that the camera is powered up
and connected to a monitor / computer to check the
desired field of view prior to fixing the camera in
place.
Iris do not accept any liability if the camera is
installed and does not cover desired field of view.
1. Fit Base
2. Slide camera cable through base
3. Set desired camera field of view
4. Slide Cowling over inner dome onto base
5. Tighten Grub Screws!
IRISx460 User Guide v2.3 April 2021
6
Inner Dome
Lens
Photo-Diode
(Light Sensor)
Infra Red LEDs
Cowling
Lock Screw
(in 2 positions)
Base
TO AVOID DAMAGE TO THE CAMERAS PAINTWORK
WHICH COULD RESULT IN EROSION TO THE
HOUSING, ENSURE THE GRUB SCREWS ARE FULLY
LOOSENED BEFORE MAKING ANY POSITIONAL
ADJUSTMENTS TO THE INNER DOME.
FAILURE TO DO SO WILL INVALIDATE ANY
WARRANTY CLAIM IF THE PAINTWORK IS
SCRATCHED OR DAMAGED.
FULLY LOOSEN PRIOR TO
ADJUSTING INNER DOME POSITION
(BOTH SIDES OF CAMERA)

Iris Innovations
Installation
WARNING!
Only trained electrical installers or competent persons
should install this product. Incorrect installation could lead
to personal injury or death and/or damage to property.
Ensure the electrical regulations specific to your region are
observed, and observed wiring colour conventions.
Ensure the cameras power supply is connected via a
suitably rated fuse or circuit breaker.
Switch off the power supply you are working on whilst
installing the camera, until the product is correctly installed.
Step 1:
Offer base into desired mounting position and mark off
screw hole positions and cable entry position through the
mounting surface. Alternatively, you can use the self
adhesive fixing template supplied to mark off the desired
fixing holes and cable entry hole.
TIP!
Power up camera and check to ensure you have the
desired field of view prior to drilling any holes and mounting
the camera in place.
Step 2:
Fit the camera base into position. Drill pilot holes
appropriate for the fixings you are using, and then screw
base into place, observing caution not to splinter or
damage the surface if fitting onto a GRP surface.
Step 3:
Present your cables to the camera through the cable entry
hole you’ve just drilled. If you have a PoE version of the
camera, this will just be a single CAT5 cable. If you have a
non PoE version, you will need a CAT5 cable and 2 cores
18AWG for the DC power. Ensure terminations are
sufficiently protected from any moisture ingress. Details on
how to fit the waterproof plug are on the next page.!
Step 4:
Fit the field installable water resistant RJ45 back-shell over
the CAT5 cable and terminate the RJ45 connector in
accordance with T568B wiring specifications. Refer to
Page 8 for further details.
Step 5:
Plug your RJ45 jack into the cameras RJ45 socket. Make
sure the fit is good and you hear the connects ‘click’ into
place. Now ensure the water resistant back shell is
tightened into place.
Step 6:
Slide the ‘slack’ cable from the camera back through the
hole in your panel, ensuring connectors are still in tact and
sit the inner dome onto the protective foam / rubber ring
on the base.
Step 7:
Place the cowling over the inner dome and move into
position. The cowling will fit over the inner dome and push
up to the base. Once in position, carefully tighten the grub
screws until they lightly hold the inner dome in position.
Now power up the camera and check you have achieved
the desired field of view. If any adjustments are required,
loosen the grub screws to make the necessary
adjustments, lightly tighten and then check again. Repeat
until you have the desired field of view. Once you are
happy with the cameras position, tighten the grub screws.!
IRISx460 User Guide v2.3 April 2021
7

Iris Innovations
How to fit Field Installable
Waterproof RJ45 Jacket
When installing in an external location, or any position that
will be prone to moisture ingress or harsh weather, it is
important the the waterproof RJ45 connector (supplied) is
used to protect the cameras connections.
!
Method
Step.1:
Feed the plug-less network cable (7) through the lock nut
(6), waterproof rubber gasket (5) (ensuring the rubber
gasket inset ridge faces the end-cap (4).
Step.2:
Crimp an RJ45 Network plug (3) onto the end of the cable
in accordance with the diagram below, taking care to
ensure the wires are terminated in the correct order and
are not crossed.
Step.3:
Place the O Seal (2) onto the end of the cameras network
interface socket (1).
Step.4:
Insert the network plug (3) into the cameras network
interface socket (1).
Step.5:
Insert the waterproof rubber gasket (5) into the waterproof
end-cap (4) and secure lock nut (6) with the waterproof
end cap (4).
Step.6:
Align the snap on waterproof end-cap (4) with the notch on
the cameras network interface socket (1) and then secure
the waterproof end-cap (4) to the cameras network
interface socket (1).!
Part No
Description
1
Cameras Network Interface Socket
2
O Seal
3
RJ45 Network Connector
4
Waterproof Endcap
5
Rubber Gasket
6
Lock Nut
7
Network cable to Router / Switch / Hub / etc..
IRISx460 User Guide v2.3 April 2021
8
Pin No
Wire Colour
1
White / Orange
2
Orange
3
White / Green
4
Blue
5
White / Blue
6
Green
7
White / Brown
8
Brown

Iris Innovations
Configuring the Camera over the
LAN
WARNING: Stay Secure!
When connecting any device to a network with access
over the internet brings risks to the security of your
network and your data. Your IRIS460 features built in User
Name and Password authentication but it is also your
responsibility to strengthen your network security where
ever possible. Please contact your IT expert for further
advise. Iris cannot provide support with any aspect of your
network security, other than the cameras built in security
settings.
Basic Setup: Single Camera / Computer
The diagram below shows a very basic setup, with a single
camera being viewed on a PC (or laptop).
Use a standard 568B ethernet CAT5 cable to hook your
computer up to the PoE injector, and then another 568B
cable to hook the camera up to the injector.
With this type of installation, you must ensure the IP
address of the camera is in the same range as the network
adapter in your computer used to communicate with the
camera. Consult documentation for your computer for
information on how to view (and edit) your network adapter
IP address.
The camera is set as default to DHCP, which means it has
no IP address set, and awaits for a router on your network
to assign the address.
To find your camera on the network, use an IP camera
discovery tool, or an ONVIF Device Manager.
A great Onvif Device Manager can be found here:https://
sourceforge.net/projects/onvifdm/!
Once you’ve downloaded and installed the Device
Manager software, open the program and then click the
REFRESH button at the bottom of the device list on the left
hand side. If everything is hooked up correctly, the details
of your camera, including its IP address, will be displayed
in the list.
If the cameras IP address falls outside the range of the IP
address of your computers network adapter, you’ll have to
change the address on your adapter so it corresponds
with the address of the camera. Once this is done (and
you’ll usually need to reboot your computer) you should
simply be able to open your web browser, type the IP
address of the camera into the address bar and access the
camera. From here, if required, you can change the IP
address of the camera as desired - back to the original
address range of your computer for example. If you do
this, then you will also have to change the address of your
network adapter back to its previous range.
Basic Setup: Single Camera / Computer via Router
using DHCP (default)
The diagram below shows a simple one camera / one
computer device, but this time a router is used to manage
your network devices and address allocation.
As mentioned previously, the camera as default is set to
obtain its IP address automatically via DHCP. This means
that once connected, your router will detect the device and
assign it an IP address within its designated range (refer to
the documentation for your router for further details). You
must also ensure the network adapter for your computer is
set to obtain its address via DHCP.!
IRISx460 User Guide v2.3 April 2021
9
PoE
Injector
Network
Cable
Network
Cable
IRISPoE1
6~36VDC
PoE
Injector
Network
Cable
Network
Cable
IRISPoE1
6~36VDC
Router
Network
Cable

Iris Innovations
Operation
IP Addressing & DHCP (Dynamic Host Control
Protocol).
Devices on your network require their own, unique IP
address. Your camera is factory set as DHCP (Dynamic
Host Control Protocol).
DHCP Addressing
DHCP allows devices on the network to receive their IP
address automatically from a server (or a device on the
network that acts as a server - such as a Raymarine MFD).
Nowadays, pretty much all routers have a DHCP server
feature, which usually just needs enabling and configuring.
Care should be taken on larger networks to ensure there
are no conflicts if multiple routers or devices are configured
as DHCP servers. Please refer to your IT specialist for
further details if you are unsure.
Raymarine MFD’s
For Raymarine MFD’s, including Axiom models, running
Lighthouse 2 or higher, all you need to do is connect the
camera to your Raymarine network and wait! Your
Raymarine device will take a few minutes to assign the
camera address at first, but once assigned, your camera
should appear within a short while after the MFD boots up
and initializes.
NOTE: The first time you hook your camera up to the
Raymarine it may take some time for the MFD to discover
the camera. This is normal.
Static (or Fixed) IP Addressing
If you are not using a DHCP server, you will need to log
onto the camera and assign an address to fit in with your
network address range. This sounds obvious, and like it
should be a basic step, but can actually be a major
challenge, as you can only log into the camera if its
address is in the same range as your network. If you do
not have experience in this field we recommend you
consult your IT specialist, as making undesirable changes
to your settings could result in major network problems.
For further details, please contact your Iris dealer.!
Discovering your Camera
To discover your camera on your network you can check
your router for attached devices (if using DHCP) or use a
software discovery tool, or an ONVIF device manager.
A great Onvif Device Manager can be downloaded from
here:https://sourceforge.net/projects/onvifdm/
Remember, you’ll only be able to find a device on your
network if it’s in the same IP address range. If you are
unsure how to do this, consult your IT specialist.
Once you have found, or set your cameras address, you
can log on to set up and view your camera.
Logging Into your Camera
From your browser, type in your cameras IP address. The
login page from the camera will be loaded up (see above).
The default log in details are as follows:
USER NAME: admin
PASSWORD:
No password is set as default.
Once you’ve entered the correct user-name and password
the main window will be displayed. You can change the
default user name and password from the cameras Set Up
window.!
IRISx460 User Guide v2.3 April 2021
10

Iris Innovations
Main Window
IRISx460 User Guide v2.3 April 2021
11
Live View
Displays the live view from the camera
Playback
Used to search for stored snap-shots and
videos as defined in Local Settings.
Remote Settings
Accesses Camera, Network and
System Setting pages.
Local Settings
Defines path on local PC for storing
snap-shots and video
Logout
Logs out of the cameras interface.
Video Definition
Toggle between Standard Definition (1280x720)
or High Definition (1920 x 1080)
Volume
Not Enabled on IRIS460
Full Screen
Scales Live Video Panel to
Full Screen
Microphone
Not Enabled on IRIS460
Snapshot
Stores snap shot to path
defined in Local Settings
Video
Stores video to path
defined in Local Settings
Camera Title
Can be toggled ON/OFF or re-labelled
in Settings Menu
Time & Date
Can be toggled ON/OFF or adjusted
in Settings Menu
Zoom
Once enabled, allows user to
draw ‘Region of Interest’
which will fill the screen
Aspect Ratio

Iris Innovations
Playback Window
Snap-Shots and Videos from the IRIS460 can be stored on
a local network device, such as a PC. To define the
storage path, format and duration, use the LOCAL
SETTINGS panel (see below).
To search for files, set your desired start time (STime) and
end time (ETime) and hit QUERY.
The list of available events will be displayed in the playback
table.
To view and event, double click on the desired entry in the
playback table.
Local Settings Window
Defines paths for storing Snap-Shots and Videos as
detailed above.
IRISx460 User Guide v2.3 April 2021
12
Playback Controls
Playback Time Line
Playback Window
Playback Table
Search Criteris
Query Button

Iris Innovations
Remote Setting Window
The Remote Settings window contains the following sub-
menus:
Camera Config
OSD Config: Sets camera name and Time / Data display " "
(shown in image below).
Image Ctrl: Sets image values (Brightness, Colour, ""
Contrast etc, as well as IR settings (see below).
Privacy Zone:Configure multiple ‘Privacy Zones’ to black " "
out areas that may either infringe privacy or "you don’t want
other people with access to the camera to see.
Use mouse (or touch-screen) to ‘draw’ privacy zones.
Network Config
The Network Config tab contains the following sub menus:
Network Config: Set IP address details, including DHCP/
Static (shown above).
Port Config: Define network port settings (shown " " "
below)."
PPPoE Config:"Enable / Disable PPPoE (default = " "
"disabled).
Email Config:" " Define email address snap-shots are "
""sent to when an alarm (motion) is " " "
triggered. This requires an email " " "
account and the SMTP server details " " "
to configure.
FTP Config:" " Configure FTP server details for " "
"remote storage.
DDnS Config:" " Configure settings if you are " " "
using a Dynamic Domain Name """Server.
RTSP Config:" " Configure RTSP port details. RTSP " "
"stream details are as follows:
MAIN Stream:"" rtsp://IP:Port/live/0/MAIN
SUB Stream:" " rtsp://IP:Port/live/0/SUB!
IRISx460 User Guide v2.3 April 2021
13

Iris Innovations
Network Config (continued...)
UPnP Config:"Configure UPnP protocol settings.
P2P Config:"Configures Peer to Peer connections. Also
displays QR Codes to download a generic F.O.C IP
camera viewer App and the uniques configuration to
enable the camera to connect to a third party VPN host for
remote viewing, which can be accessed from the App (see
below).
Code Config
The code config window is where camera resolution,
refresh rate, bit rate control etc are set. Both streams can
be configured independently.!
Alarm Config
The IRIS460 supports motion recording and scheduled
recording.
For Motion Detection, you define the areas of the screen
you wish to become ‘alarmed’ by drawing boxes as
desired in the Alarm/Motion window. Subsequently, when
motion is detected within these boxes, the camera enters
alarm state and begins recording to the path defined in
LOCAL SETTINGS.
Use mouse (or touch-screen) to ‘draw’ motion alarm
zones.
Scheduled Recording lets you define at which time and on
which days the camera records, as shown below.!
IRISx460 User Guide v2.3 April 2021
14

Iris Innovations
System Config:
The System Config window contains the following sub
menus:
TIME SETTINGS:
Configure time zone settings and set Daylight Saving
parameters
USER MANAGEMENT
Sets user accounts and privileges
DEVICE INFO
Displays camera serial number / software versions etc
LOG QUERY
Query camera error and activity log by time and date.
AUTO REBOOT
Specify a time you wish the camera to automatically reset
PTZ SETTINGS
Not Applicable
System Maintenance:
The System Maintenance menu has two sub menus:
FIRMWARE UPDATE:
Define the path new firmware is located lo perform a
firmware upgrade
RESTORE DEFAULT:
Restores the camera to its default settings.!
IRISx460 User Guide v2.3 April 2021
15

Iris Innovations
Appendix:
Connectivity Issues: The IRIS460 camera is usually
viewed via an MFD using the RTSP feed and as the
camera is set to DHCP as default, usually (and depending
on the model of MFD used) connection should be plug and
play.
There will however be certain situations where you may
want to view on a PC (computer based navigation system
for example, during manual configuration or when viewing
the camera remotely).
In this scenario, please ensure you use a compatible
browser. Please check the up to date specifications on our
website (www.boat-cameras.com) to check compatible
browsers.
Please also ensure your PC’s firewalls and Active X settings
are configured correctly.
For Active X settings, navigate to the appropriate point in
your browser security settings and allow all Active X
connections. Failure to do so may result in the camera
video not displaying correctly, even though the interface
may load correctly.
The camera acts as a ‘web server’ and certain files may
need to be automatically installed by your computer from
the camera. Ensure your security settings allow files to be
downloaded and installed from the camera.!
IRISx460 User Guide v2.3 April 2021
16

Iris Innovations
IRISx460 User Guide v2.3 April 2021
17

Iris Innovations
IRISx460 User Guide v2.3 April 2021
18

Iris Innovations
IRISx460 User Guide v2.3 April 2021
19

Iris Innovations
IRISx460 User Guide v2.3 April 2021
20
Iris Innovations Limited
Unit 240 Ordnance Business Park
Aerodrome Road
Gosport
Hampshire PO13 0FG
United Kingdom
Tel: [phone] / email: [email protected]
www.boat-cameras.com