ISESAR IS-H80s Series User manual

INTERCOM
H80S is a SIP-based, one-button screenless network door
unit with audio and video intercom, access control and
monitoring functions, which can be used in villas,
residential buildings and other application scenarios.
 One press button to call
 1-mega pixel HD Camera
 Aluminum Alloy Casing
 IP65 dust and water protection
 With Wiegand interface
 Support card/keyfob access
 Support Bluetooth access
 Support PoE
 Easy to integrated with SIP systems and services
 Front panel: Aluminum Alloy
 Camera: 1M pixels
 White light LED: Auto
 Button: 1 call button
 Microphone: -42dBV
 Speaker: 4Ω / 2W
 Ethernet: 1×RJ45, 10/100Mbps self-adaptive
 802.3af Power-over-Ethernet
 DC12V/1A connector (if not using PoE)
 Infrared sensor: Support
 Wiegand: Support
 RS485: Support
 RF card reader: 13.56MHz
 Relay out: 1
 Inputs: 2
 IP Level: IP65
 Installation: Wall-mounted
 Dimension: 170×110×21mm
 Working Humidity: ≤95%RH
 Working Temperature: -30°C ~ +70°C
 Storage Temperature: -40°C ~ +70°C
Multifunctional SIP doorphone
IS-H80sISESAR
Highlights
HIGHLIGHTS
Physical & Power
PHYSICAL&POWER
XI`AN ISESAR TECHNOLOGY CO., LTD. 
ADD:Room2306,LingxianTimesplaza,GaoxinRoad,Xian
Web:www.isesar.com

 Sensor: 1/4", CMOS
 Pixels: CIF, QCIF, VGA
 Video codec: H.264
 Video resolution: up to VGA
 Viewing angle: 110°(FOV)
Networking
Protocols: IPv4, HTTP, HTTPS, FTP, TFTP,
SNMP, DNS, SNTP, RTSP, SRTP, RTP, TCP,
UDP, TLS, ICMP, DHCP, ARP
Deployment & Maintenance
 Auto-Provisioning
 Web management portal
 Web-based packet dump
 Configuration backup / restore
 Entry log export
 Credentials export/import
 Firmware upgrade
 System logs (include door access logs)
Scenarios
 Door of office, floor and authorized areas
 Door of villa or apartment unit
 Entrance and spot in remote site
 Emergency tower
Door Entry Feature
 Unlock methods: IC card/keyfob and Bluetooth LE
 Auto-night mode with LED fill-in light
 White balance: Auto
 Minimum illumination: 0.1LUX
IS-H80sISESAR
 SIP v2 (RFC3261)
 Audio Codec: G.771a, G.711u, G.729 (Narrowband)
G.722 (Broadband)
 DTMF: In-band, RFC2833, SIP Info
 Echo Cancellation
Audio
Video
DEPLOYMENT & MAINTENANCE

21mm110mm
5.5mm
170mm
MAKE PROPERTIES SAFER
AND SMARTER

Before the installation of the device, please check you have the following items on hand.
IS-H80s Series Quick Guide
2
|
Product Overview
PRODUCT OVERVIEW
1
|
Preparation
PREPARATION
DH-H80S Waterproof cover
×1
Wall bracket
Screw
M4×30
Screw
M3×4FMO
×1 ×2
×4 ×1
21mm110mm
5.5mm
170mm
①
②
③
④
⑤
⑥
⑦
① White light LED
② RGB camera
③ Infrared sensor
④ Loudspeaker
⑤ Card Reader
⑥ Call button
⑦ Mic
MAKE PROPERTIES SAFER
AND SMARTER
1

The device can be installed in both indoor and outdoor environment.
Outdoor installation: Avoid to exposing the device to direct sunlight, which will cause damage
to device and components due to high temperature.
Indoor installation: The device should be installed on somewhere 2 meters (6 feet) away from
light or 3 meters (9 feet) away from window/door.
3
|
Installation Environment
INSTALLATION ENVIRONMENT
4
|
Installation
INSTALLATION
IS-H80s Series Quick Guide
Backlight Direct sunlight Close to light
① Lock the wall bracket on the bottom box inside the wall with four M4×30 screws.
② Let all cables go through the wall bracket and then the waterproof cover, connect them to
corresponding interfaces of device.
③ Attach the waterproof cover onto the device back panel by snap-fit.
① ② ③
MAKE PROPERTIES SAFER
AND SMARTER
2

5
|
Interfaces
INTERFACES
 Ethernet (PoE): Ethernet (PoE) connector which can provide both power and network connection.
 RS485+/RS458-/GND: Terminals for automation system control (e.g.Elevator control).
 OPEN/COM: Terminals for connecting to the cathode lock.
 CLOSE/COM: Terminals for connecting to anode lock or magnetic lock.
 D_IN1/GND: Terminals for pressing indoor button to open relay.
 D_IN2/GND: Terminals for Connecting to the door sensor.
 NC1: Default output high level, output low level when the indoor alarm is triggered.
 NC2/NC3: Reserved terminal,default output high level.
 WG_D0/WG_D1/GND: Terminals for wiegand access control.
 VCC_WG: Terminal for wiegand device power supply.
 +12V/GND: External power supply terminal if PoE is not available.
IS-H80s Series Quick Guide
④ Attach the device with waterproof cover
on the wall bracket.
⑤ Lock the device with wall bracket from
the bottom by two M3×4FMO screws.
+584
-584
DNG
Ethernet(PoE)
485+
485-
OPEN
COM
CLOSE
D_IN1
GND
D_IN2
GND
NC1
NC2
NC3
GND
WG_D0
WG_D1
VCC_WG
GND
+12V
NEPO
MOC
ESOLC
1NI_D
DNG
2NI_D
DNG
DNG
0D_GW
1D_GW
GW_CCV
1CN
2CN
3CN
Press to exit
RF CARD
④⑤
MAKE PROPERTIES SAFER
AND SMARTER
3

IS-H80s Series Quick Guide
7
|
Configurations
CONFIGURATIONS
Log into Web configuration portal of device, set up and register SIP accounts in INTERCOM-ACCOUNT
page. (You can refer to device user manual for more details)
Press on the device call button and hold for 5 secs, the device will broadcast the IP address digits by voice.
 Check IP Address
 Set SIP Account
Select DTMF mode and configure the code in SYSTEM-RELAY page of Web configuration portal. (You can
refer to device user manual for more details)
 Set DTMF Code
6
|
Specifications
SPECIFICATIONS
 OS: Linux
 Ethernet: 10M/100M adaptive
 Input power: DC12V / 1A
 PoE: 802.3af PoE
 IP level: IP65
 Front panel: Aluminum
 Working Temperature: -30℃ ~70℃
 Working Humidity: 10%~95%RH
 Equipment size: 170×110×21mm
 Installation size: Wall-mounting
8
|
Functions
FUNCTIONS
Attach the saved access card or keyfob on the card reader area of H80S to unlock the door.
 Card/Keyfob Unlock
Incoming calls to H80S will be answered automatically by default.
 Auto answer
Press the configured DTMF code on keypad of device answering the call, the lock connected on H80S
will be unlocked remotely.
 DTMF Unlock
MAKE PROPERTIES SAFER
AND SMARTER
4

 Violent vibration, collision and shock will cause damages to device.
 Intense direct sunlight will seriously affect the device performance and life span.
 Keep the access card/keyfob away from magnet and water. DO NOT fold or bend the card/keyfob.
 The height between camera and ground should be 1.5m (around 4ft 11in) to guarantee the ideal
visual angle.
IS-H80s Series Quick Guide
9
|
Precautions
PRECAUTIONS

Visual Angle
MAKE PROPERTIES SAFER
AND SMARTER
5
XI`AN ISESAR TECHNOLOGY CO., LTD.
ADD.: Room 2306, Lingxian Times plaza, Gaoxin Road, Xi`an
Web: www.isesar.com