Isotra ARTOSI User manual

1
Validity of the manual: 21.3.2022
MEASUREMENT AND ASSEMBLY MANUAL
ARTOSI PERGOLA
MEASUREMENT
In case of pergolas, the outer structure envelope is measured. The
following is entered: overall width [S], overall length [L], and passing
height [H] of each post.
The pergola’s perimeter frame must be level and rectangular in all
directions after the installation. When taking measurements, be
careful about the heights and evenness of the individual anchoring
points for the posts. The anchoring points for the posts must have
sufficient load-bearing capacity in order to withstand all loads
transferred to them by the post feet. Also pay attention to evenness
and squareness of the individual neighbouring structures to which
the pergola will be attached. If the pergola’s perimeter frame is to be anchored to surrounding structures,
said structures must have sufficient load-bearing capacity to withstand all loads transferred to them by the
perimeter frame. When incorporating the pergola to or close to surrounding structures, it is necessary to
consider the possibility of dimensional changes to the pergola due to the surrounding temperatures (see
Artosi Technical Manual).
LINEAR EXPANSION
When the temperature of aluminium increases, the metal will expand; this phenomenon is called thermal
expansion. The coefficient of thermal expansion of aluminium alloy is 23.5 μm/(m*K).
Example:
At 20 °C, an aluminium profile measures 7000 mm. When heated to 50 °C – during a sunny day –it will
measure 7005 mm due to thermal expansion. The length will increase by +5 mm as a result of the change in
aluminium temperature.
When incorporating the pergola to surrounding structures, it is important to consider change in the pergola
dimensions due to ambient temperature.
When taking measurements of screen roller blinds and installing them in the pergola, it is necessary to
consider thermal expansion of the aluminium profile in relation to ambient temperature. We recommend
that measurements be taken at ambient temperatures of 23 ±5 °C.
ISOTRA a. s.
Bílovecká 2411/1, CZ-74601 Opava
19
EN 13561:2015
ARTOSI
CPR 043/2019
Exterior Sun Shield
Wind resistance: 6
Total solar transmittance factor gtot: 0.03–0.6

2
Validity of the manual: 21.3.2022
MEASUREMENT AND ASSEMBLY MANUAL
ORDERING
The pergola ordered must meet the conditions specified in the ARTOSI Technical Manual. The ARTOSI
Designer, available at Isotra’s e-shop, must be used for ordering. This graphical interface will guide you
through the selection of the individual elements, so that the pergola properly fulfils its function.
LIST OF TOOLS
TOOLS NECESSARY FOR INSTALLATION
•Tape measure
•Spirit lever (Levelling laser)
•Socket spanner 4, 5, 6
•Ratchet spanner + 30 cm lever
•Sockets for ratchet spanner 5.5 mm, 17 mm, 19 mm
•Combination (ratchet) spanner 10, 15, 17
•Torx T15 screwdriver
•Flathead screwdriver
•Utility knife
•Gun applicator for sealants
•Sealant (we recommend Soudal Silirub 2)
•Spray with soap water
TOOLS RECOMMENDED FOR INSTALLATION
•Two ladders adjustable to the pergola
height
•Hammer drill + drill bits
•Step drill bit
•Angle grinder + diamond disc
•Vacuum cleaner
•Garbage bags
•Compression bands
•Bolts with sealing rubbers

3
Validity of the manual: 21.3.2022
MEASUREMENT AND ASSEMBLY MANUAL
LIST OF SYMBOLS USED


x
Measure
Tighten –slightly
Tighten –fully
Level
Cut off
Seal
Smooth sealant
Remove excess sealant
Prepare anchors to vertical
structures. Anchor Ø.
Prepare anchors to horizontal
structures. Anchor Ø.
Fix anchors to vertical
structures
Fix anchors to horizontal
anchor points
Water
Correct
Incorrect
!
Note
Assembly
Disassembly

MEASUREMENT AND ASSEMBLY MANUAL
Validity of the manual: 28.6.2023
4
MEASUREMENTS –Type A, Type B, Type D

MEASUREMENT AND ASSEMBLY MANUAL
Validity of the manual: 28.6.2023
5
1:1 page 27-28

MEASUREMENT AND ASSEMBLY MANUAL
Validity of the manual: 28.6.2023
6
ASSEMBLY –POSTS –Type A, Type B, Type D

MEASUREMENT AND ASSEMBLY MANUAL
Validity of the manual: 28.6.2023
7
ASSEMBLY –WALL PROFILES –Type A, Type B, Type D

MEASUREMENT AND ASSEMBLY MANUAL
Validity of the manual: 28.6.2023
8
ASSEMBLY –FRAME –Type A

MEASUREMENT AND ASSEMBLY MANUAL
Validity of the manual: 28.6.2023
9

MEASUREMENT AND ASSEMBLY MANUAL
Validity of the manual: 28.6.2023
10
ASSEMBLY –FRAME –Type B

MEASUREMENT AND ASSEMBLY MANUAL
Validity of the manual: 28.6.2023
11

MEASUREMENT AND ASSEMBLY MANUAL
Validity of the manual: 28.6.2023
12

MEASUREMENT AND ASSEMBLY MANUAL
Validity of the manual: 28.6.2023
13
ASSEMBLY –FRAME –Type D

MEASUREMENT AND ASSEMBLY MANUAL
Validity of the manual: 28.6.2023
14

MEASUREMENT AND ASSEMBLY MANUAL
Validity of the manual: 28.6.2023
15
ASSEMBLY –STRUCTURE LEVELLING –Type A, Type B, Type D

MEASUREMENT AND ASSEMBLY MANUAL
Validity of the manual: 28.6.2023
16
ASSEMBLY –CONNECTING EAVES –Type A, Type B, Type D

MEASUREMENT AND ASSEMBLY MANUAL
Validity of the manual: 28.6.2023
17

MEASUREMENT AND ASSEMBLY MANUAL
Validity of the manual: 28.6.2023
18
ASSEMBLY –SLATS WITH COTTERS –Type A, Type B, Type D

MEASUREMENT AND ASSEMBLY MANUAL
Validity of the manual: 28.6.2023
19
ASSEMBLY –SLATS –Type A, Type B, Type D

MEASUREMENT AND ASSEMBLY MANUAL
Validity of the manual: 28.6.2023
20
ASSEMBLY –COVERS –Type A, Type B, Type D