ISSI IS32FL3738 User manual

6x8 MATRIX LED DRIVER
Integrated Silicon Solution, Inc. – www.issi.com 1
Rev. C, 03/22/2017
DESCRIPTION
The IS32FL3738 is an automotive grade general
purpose 6×8 LEDs matrix driver with 1/12 cycle rate.
The device can be programmed via an I2C compatible
interface. Each LED can be dimmed individually with
8-bit × 4 PWM data which allowing 512 steps of linear
dimming.
IS32FL3738 features 3 Auto Breathing Modes which
are noted as ABM-1, ABM-2 and ABM-3. For each Auto
Breathing Mode, there are 4 timing characters which
include current rising / holding / falling / off time and 3
loop characters which include Loop-Beginning /
Loop-Ending / Loop-Times. Every LED can be
configured to be any Auto Breathing Mode or
No-Breathing Mode individually.
FEATURES
Up to 48 LEDs (6×8) in dot matrix
Programmable 6×8 (16 RGBs) matrix size with
de-ghost function
Selectable 3 Auto Breath Modes for each dot
Auto Breath Loop Features interrupt pin inform
MCU Auto Breath Loop completed
Auto Breath offers 128 steps gamma current,
interrupt and state look up registers
256 steps Global Current Setting
Individual 512 PWM control steps
Individual Auto Breath Mode select
Individual open and short error detect function
QUICK START
Figure 1: Photo of IS32FL3738 Evaluation Board
(V01A board with 12V DC input please refer to Appendix
Ⅰ )
RECOMMENDED EQUIPMENT
5.0V, 2A Micro USB
Arduino IDE, www.arduino.cc/en/Main/Software
Arduino code download from ISSI website
ABSOLUTE MAXIMUM RATINGS
≤5.5V Micro USB DC power supply
Caution: Do not exceed the conditions listed above, otherwise
the board will be damaged.
PROCEDURE
The IS32FL3738 evaluation board is fully assembled,
tested and comes programmed with evaluation
software. Follow the steps listed below to verify board
operation.
Caution: Do not turn on the power supply until all connections
are completed.
1) Connect the 5VDC USB power to the Micro USB.
2) Press K1 to cycle through a display mode.
EVALUATION BOARD OPERATION
The IS32FL3738 evaluation board drives16 RGB
LEDs located underneath the light dispersing filter.
Every press of the K1 switch will cycle through one of
the 8 pre-programmed lighting sequences below:
1) White LED
2) Rainbow bar
3) Red color breath
4) Green color breath
5) Blue color breath
6) Pink color breath
7) Yellow color breath
8) Cyan color breath
Note: IS32FL3738 solely controls the FxLED function on the
evaluation board.
ORDERING INFORMATION
Part No. Temperature Range Package
IS32FL3738-ZLA3-EB -40°C to +125°C (Automotive) eTSSOP-28, Lead-free
Table 1: Ordering Information
For pricing, delivery, and ordering information, please contacts ISSI’s analog marketing team at
[email protected] or [phone].

6x8 MATRIX LED DRIVER
Integrated Silicon Solution, Inc. – www.issi.com 2
Rev. C, 03/22/2017
SOFTWARE CONTROL
The evaluation board comes with an Arduino
compatible microcontroller circuit preloaded with
IS32FL3738 demonstration firmware, called a sketch.
This allows the functionality of the IS32FL3738 to be
verified before starting firmware development.
The Arduino hardware consists of an Atmel
microcontroller with a bootloader allowing quick
firmware updates. First download the latest Arduino
Integrated Development Environment IDE (1.6.12 or
greater) from www.arduino.cc/en/Main/Software.
Then download the latest IS32FL3738 firmware
(sketch) from the ISSI website
www.issi.com/US/product-analog-automotive.shtml.
When using the Arduino environment, please select
Genuino UNO as shown below, then select the serial
port. Follow the standard procedure to upload the
latest IS32FL3738 firmware into the Arduino; then
use the IDE to modify it. There is no additional
software required to run the eval board.
EXT-SOFTWARE CONTROL
The IS32FL3738 can also be driven by an external IIC
source.
Follow the steps below to configure the eval board for
external control.
1) Open the two pins of J7 on the right side, to
disable the onboard Arduino and enable external
control (the SDA SCL and SDB become high
impedance).
2) Default VIO is 5V, if you use a 3.3V IO, connect
3.3V to VIO pin in J7.
3) Connect SDB to VIO or high level IO
4) Connect external IIC to the IIC pins of J7
5) Start external IIC control.
Please refer to the datasheet to get more information about
IS32FL3738

6x8 MATRIX LED DRIVER
Integrated Silicon Solution, Inc. – www.issi.com 3
Rev. C, 03/22/2017
Figure 2: IS32FL3738 Application Schematic
PE6/INT6/AIN0 1
UVCC
2
D-
3
D+
4
UGND
5
UCAP
6
VBUS 7
PB0/SS/PCINT0
8
PB1/SCLK/PCINT1 9
PB2/PDI/MOSI/PCINT2 10
PB3/PDO/MISO/PCINT3 11
PB7/OC0A/OC1C/RTS 12
RESET
13
VCC
14
GND
15
XTAL2
16
XTAL1
17
PD0/OC0B/SCL/INT0 18
PD1/SDA/INT1 19
PD2/RXD1/INT2 20
PD3/TXD1/INT3 21
PD5/XCK1/CTS
22
GND
23
AVCC
24
PD4/ICP1/ADC8 25
PD6/T1/OC4D/ADC9 26
PD7/T0/OC4D/ADC10 27
PB4/PCINT4/ADC11 28
PB5/PCINT5/OC1A/OC4B/ADC12 29
PB6/PCINT6/OC1B/OC4B/ADC13 30
PC6/OC3A/OC4A 31
PC7/ICP3/CLK0/OC4A
32
PE2/HWB
33
VCC
34
GND
35
PF7/ADC7/TDI 36
PF6/ADC6/TDO 37
PF5/ADC5/TMS 38
PF4/ADC4/TCK 39
PF1/ADC1 40
PF0/ADC0 41
AREF
42
GND
43
AVCC
44
U1
ATMEGA32U4
5V
10K
R1
100n
C11
100n
C10
GND
13
4 2
TS42
SMD-KEY-5P
GND
RD-
RD+
Y1
16M
22pF
C12
22pF
C13
GND
1uF
C5
100nF
C6
GND
OSC_OUT
OSC_IN
1uF
C7
AVCC
1K
R7
1K
R8
RX
L
TX
ON 1K
R6
1K
R5
10K
R4
UCAP
AREF
GND
5V
RX
Blue
Green
RXLED
IO13
TXLED
HWB
VUSB
A5
A4
A0
A1
A2
A3
D1/TX
D0/RX
D2/SDA
D3/SCL
SDB
D5
D6
KEY
IO12
IO11
IO10
IO9
IO8
MOSI
MISO
SCK
VCC
1
USB_DM
2
USB_DP
3
NC
4
GND
5
J3
USB_Micro
MSMF050- 2
F1
VUSB
22RRP3B
22RRP3A
D-
D+
RD+
RD-
CG0603MLC-05E
Z2 Z1
GND
1uF
C14
100nF
C9
10K
R2
USB_VCC
GND
1
1
3
3
5
5
22
44
66
J4
ICSP
MISO
SCK
RESET
5V
MOSI
GND
3 2
1
T1
FDN340P
VUSB VIN 5V
IN
3
GND1
OUT 2
U2
NCP1117-5
10K
R9
100nF
C1
1uF
C3
100nF
C2
5V
GND
VIN
IN
1
GND
2ON/OFF
3OUT 4
NC/FB 5
U4
LP2985-33DBVR
5V
GND
1uF
C4
3.3V
GND
3V3 REG5V REG5V SELECTOR(USB)
23
1
T2
PMV48XP
5V
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
17
17
J5 11
22
33
44
55
66
77
88
99
10 10
11 11
12 12
13 13
14 14
15 15
16 16
17 17
J6
MOSI
RXLED/SS
D1/TX
D0/RX
RESET
GND
D2/SDA
D3/SCL
D4
D5
D6
D7
IO8
IO9
IO10
IO11
IO12
SCK
MISO
VIN
GND
RESET
5V
A5
A4
A3
A2
A1
A0
AREF
3.3V
IO13
GND
OUTIN
TX
RESET
D2
CD1206-S01575
Arduino
IS32FL3738
CS8 1
REST
2
AVCC
3
VIO 4
SYNC
5
SDA
6
SCL
7
ADDR
8
INTB
9
SDB
10
GND
11
SW1 12
SW2 13
PGND
14
SW3 15
SW4 16
SW5 17
PGND
18
SW6 19
CS1 20
CS2 21
PVCC
22
CS3 23
CS4 24
CS5 25
CS6 26
PVCC
27
CS7 28
U5
IS3738
0.1uF
C20 5V
5V
5V
R20
4.7K
R21
4.7K
R22
100K
VIO
R24
100K R23 20K
SDA
SCL
INTB
SDB
SYNC
REST
R25
100K
GND
0.1uF
C23
GND
VIO
CS1
CS2
CS3
CS4
CS5
CS6
CS7
CS8
SW1
SW2
SW3
SW4
SW5
SW6
0.1uF
C21
0.1uF
C22
ADDR
R26
1k 5V
K1
MODE
GND
R27
10K
0.1uF
C24
5V
GND
KEY
R28
0R
R29
100K
VCC
GND
A5
JP1
GND
GND
GND
MH2029-300Y
L2
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
J7
GND
GND
INTB
SYNC
ADDR
VIO
SDB
GND
SCL
SDA
5V_J7
D3
DFL240
A5
A5-2
A5-2
1uF
C26
1uF
C25
GND
GND
5V
LED Matrix
LD1 LD2 LD3 LD4 LD5 LD6 LD14 LD15LD7 LD8 LD12 LD13LD9 LD10 LD11 LD16
CS1
CS2
CS3
CS4
CS5
CS6
CS7
CS8
SW1
SW2
SW3
SW4
SW5
SW6

6x8 MATRIX LED DRIVER
Integrated Silicon Solution, Inc. – www.issi.com 4
Rev. C, 03/22/2017
BILL OF MATERIALS - Arduino
Name Symbol Description Qty Supplier Part No.
MCU U1 Microcontroller 1 ATM ATMEGA32U4
LDO U2 Reduced voltage 1 ON NCP1117-5
LDO U4 Reduced voltage 1 TI LP2985-33DBVR
Triode T1 FET 1 FAIRCHILD FDN340P
Triode T2 FET 1 NXP PMV48XP
Crystal Y1 Crystal, 16MHz 1 Risym 3225 16MHz
Button K1 Button SMD 1 MT SMD-KEY-5P
LED ON,TX,RX LED, SMD Blue 3 EVERLIGHT 0603
LED L LED, SMD Green 1 EVERLIGHT 0603
F1 F1 SMD Fuse 1 MF MSMF050-2
Beads L2 Beads 1 BOURNS MH2029-300Y
Diode D2 Diode, SMD 1BOURNS CD1206-S01575
Varistor Z1,Z2 Varistor 2 BOURNS CG0603MLC-05E
Resistor RP3A,PR3B RES,22R,1/16W,±5%,SMD 2 Yageo RC0603JR-0722RL
Resistor R5,R6,R7,R8 RES,1k,1/16W,±5%,SMD 4 Yageo RC0603JR-071KL
Resistor R1,R2,R4,R9 RES,10k,1/16W,±5%,SMD 4 Yageo RC0603JR-0710KL
Capacitor C12,C13 CAP,22pF,16V,±20%,SMD 2 Yageo CC0603KKX7R9BB22
Capacitor C1,C2,C6,
C9,C10,C11 CAP,100nF,16V,±20%,SMD 6 Yageo CC0603KKX7R9BB101
Capacitor C3,C4,C5,C7,C14 CAP,1µF,16V, ±20%,SMD 4 Yageo CC0603KKX7R9BB105
BILL OF MATERIALS – IS32FL3738
Name Symbol Description Qty Supplier Part No.
LED Driver U5 Matrix LED Driver 1 ISSI IS32FL3738
RGB LED LD1~LD16 RGB LED, SMD 16 ROHM SMLV56RGB1W1
Diode D3 Diode, SMD 1 DIODES DFLS240
Resistor R20,R21 RES,4.7k,1/16W,±5%,SMD 2 Yageo RC0603JR-074K7L
Resistor R22,R24,R25,R29 RES,100k,1/16W,±5%,SMD 4 Yageo RC0603JR-07100KL
Resistor R23 RES,20k,1/16W,±5%,SMD 1 Yageo RC0603JR-0720KL
Resistor R26 RES,1k,1/16W,±5%,SMD 1 Yageo RC0603JR-071KL
Resistor R27 RES,10k,1/16W,±5%,SMD 1 Yageo RC0603JR-0710KL
Resistor R28 RES,0k,1/16W,±5%,SMD 1 Yageo RC0603JR-070KL
Capacitor C20,C21,C22,C23,C24 CAP,0.1µF,16V,±20%,SMD 5 Yageo CC0603KKX7R9BB104
Capacitor C25,C26 CAP,1µF,16V,±20%,SMD 2 Yageo CC0603KKX7R9BB105
Button K1(Bottom) Button 1
Bill of Materials, refer to Figure 1 above.

6x8 MATRIX LED DRIVER
Integrated Silicon Solution, Inc. – www.issi.com 5
Rev. C, 03/22/2017
2
23
3
2
22
2
12345678910111214 13
97654321 8 10 11 12 13
222
221
1234567891011121314151617
1234567891011121314151617
1
1
0
0
0
0
2 3
1 0
Figure 3: Board Component Placement Guide - Top Layer
0
0
0
0
0
0
0
0
0
0
0 0
0
0
0
0
0
0
0
0
0
0
0
0 0
00
0 00 0 000 0 000 0 000 0 000 0 000 0 000 0 000 0 000 0 000 0 000 0 000 0 000 0 000 0 000 0 000 0
00 0 000 0 000 0 000 0 000 0 000 0 000 0 000 0 000 0 000 0 000 0 000 0 000 0 000 0 000 0 000 00
2
23
3
2
22
2
12345678910111214 13
1 2
97654321 8 10 11 12 13
12
1 2
1 2
1 2
1 2
1 2
1
2
1
2
1 2
1 2
29
12
222
221
1
2
5
4
3
1234567891011121314151617
1234567891011121314151617
1
2
4
3
1
1
0
0
0
0
1
2
1 2
3
1 2
3
1
2
1
2
1
2
1
2
1212
1
2
1
2
12
0
2
12
1
2
1
12
1
2
12
2 3
1 0
Figure 4: Board PCB Layout - Top Layer

6x8 MATRIX LED DRIVER
Integrated Silicon Solution, Inc. – www.issi.com 6
Rev. C, 03/22/2017
2
23
3
2
22
2
12345678910111214 13
97654321 8 10 11 12 13
222
221
1234567891011121314151617
1234567891011121314151617
1
1
0
0
0
0
2 3
1 0
Figure 5: Board Component Placement Guide - Bottom Layer
2
23
3
2
22
2
12345678910111214 13
12
1 2
97654321 8 10 11 12 13
1 2
1 2
222
221
1234567891011121314151617
1234567891011121314151617
121 2
1
1
0
0
0
0
4
5
1
2
3
12 1 2
1 2
2
1
1 2
1
2
12
2
1
12
4
3 2 1
1 2
1
2
12
1 2
1
2
12
2 3
1 0
12
Figure 6: Board PCB Layout - Bottom Layer
Copyright©2017IntegratedSiliconSolution,Inc.Allrightsreserved.ISSIreservestherighttomakechangestothisspecificationanditsproductsatany
timewithoutnotice.ISSIassumesnoliabilityarisingoutoftheapplicationoruseofanyinformation,productsorservicesdescribedherein.Customersare
advisedtoobtainthelatestversionofthisdevicespecificationbeforerelyingonanypublishedinformationandbeforeplacingordersforproducts.
IntegratedSiliconSolution,Inc.doesnotrecommendtheuseofanyofitsproductsinlifesupportapplicationswherethefailureormalfunctionofthe
productcanreasonablybeexpectedtocausefailureofthelifesupportsystemortosignificantlyaffectitssafetyoreffectiveness.Productsarenot
authorizedforuseinsuchapplicationsunlessIntegratedSiliconSolution,Inc.receiveswrittenassurancetoitssatisfaction,that:
a.)theriskofinjuryordamagehasbeenminimized;
b.)theuserassumeallsuchrisks;and
c.)potentialliabilityofIntegratedSiliconSolution,Incisadequatelyprotectedunderthecircumstances

6x8 MATRIX LED DRIVER
Integrated Silicon Solution, Inc. – www.issi.com 7
Rev. C, 03/22/2017
REVISION HISTORY
Revision Detail Information Date
A Initial release 2016.09.18
B
1. Deleted 12V, 1A power supply.
2. Update schematic and PCB.
3. Update bill of materials
2016.11.04
C Correct the PWM level to 512 levels, please check datasheet for more information. 2017.03.22

6x8 MATRIX LED DRIVER
Integrated Silicon Solution, Inc. – www.issi.com 8
Rev. C, 03/22/2017
APPENDIX Ⅰ: V01A GUIDE
QUICK START
Figure 7: Photo of IS32FL3738 Evaluation Board
RECOMMENDED EQUIPMENT V01A
5.0V, 2A Micro USB or 12V, 1A power supply
ABSOLUTE MAXIMUM RATINGS V01A
≤17V DC power supply
≤5.5V Micro USB DC power supply
Caution: Do not exceed the conditions listed above, otherwise
the board will be damaged.
PROCEDURE V01A
The IS32FL3738 evaluation board is fully assembled
and tested. Follow the steps listed below to verify
board operation.
Caution: Do not turn on the power supply until all connections
are completed.
1) Connect the 12VDC power to the connector or
5VDC USB power to the Micro USB.
2) Turn on the power supply, pay attention to the
supply current. If the current exceeds 1A, please
check for circuit fault.
EVALUATION BOARD OPERATION V01A
The IS32FL3738 evaluation board has three
animation display modes. Press K1 to switch
configurations.
1) White LED
2) Rainbow bar
3) Red LED breath
4) Green LED breath
5) Blue LED breath
6) Red and blue LED breath
7) Red and green LED breath
8) Blue and green LED breath
Note: IS32FL3738 solely controls the FxLED function on the
evaluation board.
SOFTWARE CONTROL
The IS32FL3738 use Arduino as is master controller,
if using Arduino environment, please select Genuino
UNO. No driver is need when initial the hardware.
EXT-SOFTWARE CONTROL V01A
The IS32FL3738 can set its I2C bus interface logic
threshold based on the voltage on the VIO pin.
Follow the steps listed below for external control.
1) Open JP1 to disconnect the I2C communication,
and connect an external MCU VCC to VIO.
2) Pull-up the SDB to VIO.
3) Connect the 12VDC power to the connector or
5VDC power to the Micro USB.
4) Turn on the power supply pay attention to the
supply current. If the current exceeds 1A, please
check for circuit fault.
5) Start external IIC control.
Please refer to the datasheet to get more information about
IS32FL3738

6x8 MATRIX LED DRIVER
Integrated Silicon Solution, Inc. – www.issi.com 9
Rev. C, 03/22/2017
Figure 8: IS32FL3738 Application Schematic: V01A
PE6/INT6/AIN0 1
UVCC
2
D-
3
D+
4
UGND
5
UCAP
6
VBUS 7
PB0/SS/PCINT0
8
PB1/SCLK/PCINT1 9
PB2/PDI/ MOSI/PCINT2 10
PB3/PDO/MISO/PCINT3 11
PB7/OC0A/OC1C/RTS 12
RESET
13
VCC
14
GND
15
XTAL2
16
XTAL1
17
PD0/OC0B/SCL/INT0 18
PD1/SDA/INT1 19
PD2/RXD1/INT2 20
PD3/TXD1/ INT3 21
PD5/XCK1/CTS
22
GND
23
AVCC
24
PD4/ICP1/ADC8 25
PD6/T1/OC4D/ADC9 26
PD7/T0/OC4D/ADC10 27
PB4/PCINT4/ ADC11 28
PB5/PCINT5/OC1A/OC4B/ADC12 29
PB6/PCINT6/OC1B/OC4B/ADC13 30
PC6/OC3A/OC4A 31
PC7/ICP3/CLK0/OC4A
32
PE2/HWB
33
VCC
34
GND
35
PF7/ADC7/TDI 36
PF6/ADC6/TDO 37
PF5/ADC5/TMS 38
PF4/ADC4/TCK 39
PF1/ADC1 40
PF0/ADC0 41
ARE F
42
GND
43
AVCC
44
U1
ATMEGA32U4
5V
MH2029-300Y
L2
10K
R1
100n
C11
100n
C10
GND
13
4 2
K1
SMD-KEY-5P
GND
RD-
RD+
Y1
16M
22pF
C12
22pF
C13
GND
1uF
C5
100nF
C6
GND
OSC_OUT
OSC_IN
1uF
C7
AVCC
1K
R7
1K
R8
RX
L
TX
ON 1K
R6
1K
R5
10K
R4
UCAP
ARE F
GND
5V
RX
Blue
Green
RXLED
IO13
TXLED
HWB
VUSB
A5
A4
A0
A1
A2
A3
D1/ TX
D0/ RX
D2/ SDA
D3/ SCL
SDB
D5
D6
KEY
IO12
IO11
IO10
IO9
IO8
MOSI
MISO
SCK
VCC
1
USB_DM
2
USB_DP
3
NC
4
GND
5
USB_Micro
MSMF050-2
F1
VUSB
22R
R3
22R
R10
D-
D+
RD+
RD-
CG0603MLC-05E
Z2 Z1
GND
22uF
C14
100nF
C9
10K
R2
USB_VCC
GND
1
1
3
3
5
5
22
44
66
ICSP
MISO
SCK
RESET
5V
MOSI
GND
3 2
1
T1
FDN340P
VUSB VIN 5V
IN
3
GND1
OUT 2
U2
NCP1117-5
10K
R9
100nF
C1
22uF
C3
100nF
C2
5V
GND
VIN
IN
1
GND
2ON/OFF
3OUT 4
NC/ FB 5
U4
LP2985-33DBVR
5V
GND
1uF
C4
3.3V
GND
3V3 REG5V REG5V SELECTOR(USB)
23
1
T2
PMV48XP
5V
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
17
17
J5 11
22
33
44
55
66
77
88
99
10 10
11 11
12 12
13 13
14 14
15 15
16 16
17 17
J6
MOSI
RXLED/SS
D1/ TX
D0/ RX
RESET
GND
D2/ SDA
D3/ SCL
D4
D5
D6
D7
IO8
IO9
IO10
IO11
IO12
SCK
MISO
VIN
GND
RESET
5V
A5
A4
A3
A2
A1
A0
AREF
3.3V
IO13
GND
OUTIN
TX
RESET
D2
CD1206-S01575
Arduino
IS32FL3738
CS8 1
REST
2
AVCC
3
VIO 4
SYNC
5
SDA
6
SCL
7
ADDR
8
INTB
9
SDB
10
GND
11
SW1 12
SW2 13
PGND
14
SW3 15
SW4 16
SW5 17
PGND
18
SW6 19
CS1 20
CS2 21
PVCC
22
CS3 23
CS4 24
CS5 25
CS6 26
PVCC
27
CS7 28
U2
IS3738
0.1uF
C14
5V
5V
5V
R6
4.7K
R7
4.7K
R9
100K
GND
GND
GND
VIO
R10
100K R14 20K
SDA
SCL
INTB
SDB
SYNC
REST
R8
100K
GND
0.1uF
C11
GND
VIO
CS1
CS2
CS3
CS4
CS5
CS6
CS7
CS8
SW1
SW2
SW3
SW4
SW5
SW6
0.1uF
C13
0.1uF
C12
ADDR
GND 5
RT 6
VIN 7
BS 8
SW
1
COMP
3
FB
4
EN
2
Thermal Pad 9
U1
IS32PM3415
R5
200K
R3
100K
R4
51K
C7
330pF
C6
NC
C3
0.1uF
C2
4.7uF
C4
0.1uF
C9
10uF
EN
EN
D2
SS36
L1
22uH
C5
NC
VOUT
SW
GND
1GND
2VCC
3VCC
4*
*
D1
SS36
C1
100uF/25V
C16
100uF/25V
R1
62K
R2
12K
GND
C15
1uF
VIN
3Vout 2
ADJ1
U3
LM317
R15
390R
R16
120R
C8
100uF/25V
VOUT 5V
GND
GND
K1
MODE
GND
R11
10K
0.1uF
C9
5V
GND
KEY
R12
0R
R13
NC
5V
3V
R18
51K
R17
51K
VCC
GND
A5
JP1
GND
LED Matrix
LD1 LD2 LD3 LD4 LD5 LD6 LD14 LD15LD7 LD8 LD12 LD13LD9 LD10 LD11 LD16
CS1
CS2
CS3
CS4
CS5
CS6
CS7
CS8
SW1
SW2
SW3
SW4
SW5
SW6

6x8 MATRIX LED DRIVER
Integrated Silicon Solution, Inc. – www.issi.com 10
Rev. C, 03/22/2017
BILL OF MATERIALS (EVB Part)
Name Symbol Description Qty Supplier Part No.
Buck Chip U1 Buck Chip 1 ISSI IS32PM3415
LED Driver U2 Matrix LED Driver 1 ISSI IS32FL3738
LDO U3 Reduced voltage 1 ST LM317D2T
Diode LD1~LD16 RGB LED, SMD 16 ROHM SMLV56RGB1W1
Diode D1,D2 Diode, SMD 2 DIODES SS36
Resistor R5 RES,200k,1/16W,±5%,SMD 1 Yageo RC0603JR-07200KL
Resistor R3,R8,R9,R10 RES,100k,1/16W,±5%,SMD 4 Yageo RC0603JR-07100KL
Resistor R1 RES,62k,1/16W,±5%,SMD 1 Yageo RC0603JR-0762KL
Resistor R4,R17,R18 RES,51k,1/16W,±5%,SMD 3 Yageo RC0603JR-0751KL
Resistor R14 RES,20k,1/16W,±5%,SMD 1 Yageo RC0603JR-0720KL
Resistor R2 RES,12k,1/16W,±5%,SMD 1 Yageo RC0603JR-0712KL
Resistor R11 RES,10k,1/16W,±5%,SMD 1 Yageo RC0603JR-0710KL
Resistor R6,R7 RES,4.7k,1/16W,±5%,SMD 2 Yageo RC0603JR-074K7L
Resistor R15 RES,390R,1/16W,±5%,SMD 1 Yageo RC0603JR-07390RL
Resistor R16 RES,120R,1/16W,±5%,SMD 1 Yageo RC0603JR-07120RL
Resistor R12 RES,0R,1/16W,±5%,SMD 1 Yageo RC0603JR-070RL
Resistor R13 NC 1
Capacitor C15 CAP,1µF,16V,±20%,SMD 1 Yageo CC0603KKX7R9BB105
Capacitor C7 CAP,330pF,16V,±20%,SMD 1 Yageo CC0603KKX7R9BB331
Capacitor C4,12 CAP,4.7µF,16V, ±20%,SMD 2 Yageo CC0603KKX7R9BB476
Capacitor C6,C7 CAP,33pF,16V,±20%,SMD 2 Yageo CC0603KKX7R9BB330
Capacitor C8,C9,C10 CAP,0.1µF,16V,±20%,SMD 3 Yageo CC0603KKX7R9BB104
Button K1 Button SMD 1