ITALCOM TWISTx2 User manual

1
User manual

2
Table of Contents
1 General Information .......................................................4
1.1 Brief 4
1.2 Safety Precautions...........................................................................................................................5
1.3 General precautions ........................................................................................................................5
1.4 Precautions for mobile phone use ...................................................................................................5
1.5 Precautions for battery usage ..........................................................................................................6
1.6 Precautions for usage of charger.....................................................................................................7
1.7 Cleaning and Maintenance..............................................................................................................7
1.8 General Precautions........................................................................................................................7
2 Before Use................................................................8
2.1 SIM card .........................................................................................................................................8
2.1.1 Insert and pull out the SIM card...................................................................................................8
2.2 Battery.............................................................................................................................................9
2.2.1 Charge the Battery .......................................................................................................................9
2.3 Power on .......................................................................................................................................10
2.4 The use of USB data route............................................................................................................10
2.5 Install and pull out T-flash card.....................................................................................................10
3 Basic Description........................................................11
3.1 About the Keypads........................................................................................................................ 11
3.1.1 Basic Keys ................................................................................................................................. 11
3.1.2 Music Keys ................................................................................................................................ 11
3.2 Call functions................................................................................................................................ 11
3.2.1 Make a call................................................................................................................................. 12
3.2.2 Answer a call..............................................................................................................................12
3.2.3 Reject a call................................................................................................................................12
3.2.4 Menu available during a call......................................................................................................13
3.3 Hand-free function........................................................................................................................13
4 Menu Introduction........................................................13
4.1 Phone book ...................................................................................................................................13
4.2 Messaging.....................................................................................................................................15
4.2.1 NYX Connect Mail....................................................................................................................15
4.2.2 NYX Messenger ........................................................................................................................15
4.2.3 Write message............................................................................................................................15
4.2.4 Inbox..........................................................................................................................................15
4.2.5 Drafts .........................................................................................................................................16
4.2.6 Outbox .......................................................................................................................................17
4.2.7 MMS..........................................................................................................................................18
4.2.8 Broadcast Message.....................................................................................................................19

3
4.2.9 Templates...................................................................................................................................20
4.2.10 SMS settings ............................................................................................................................20
4.3 Camera..........................................................................................................................................21
4.4 Internet service..............................................................................................................................21
4.4.1 WAP...........................................................................................................................................21
4.4.2 Data account ..............................................................................................................................21
4.7 Music Player .................................................................................................................................22
4.12 Games .........................................................................................................................................22
4.13 Organizer ....................................................................................................................................22
4.13.1 Alarm .......................................................................................................................................22
4.13.2 Calendar...................................................................................................................................22
4.13.3 Calculator.................................................................................................................................23
4.13.4 Clock........................................................................................................................................23
4.13.5 Currency converter...................................................................................................................23
4.13.6 E-book reader...........................................................................................................................23
4.13.7 Privacy lock .............................................................................................................................23
4.13.8 Stopwatch.................................................................................................................................23
4.13.9 Tasks ........................................................................................................................................24
4.13.10 World clock............................................................................................................................24
4.14 Multimedia..................................................................................................................................24
4.14.1 Image Viewer........................................................................................................................... 24
4.14.2 Video Recorder ........................................................................................................................25
4.14.3 Video Player.............................................................................................................................25
4.14.4 Sound recorder.........................................................................................................................25
4.14.5 Radio FM.................................................................................................................................26
4.17 Call history..................................................................................................................................26
4.18 File Manager...............................................................................................................................29
4.19 Services.......................................................................................................................................29
4.20 Settings .......................................................................................................................................29
4.20.1 Dual SIM settings ....................................................................................................................29
4.20.2 User Profiles ............................................................................................................................30
4.20.2.1 General..................................................................................................................................30
4.20.2.2 Meeting.................................................................................................................................30
4.20.2.3 Outdoor.................................................................................................................................30
4.20.2.4 Indoor....................................................................................................................................30
4.20.2.5 Headset..................................................................................................................................30
4.20.2.6 Bluetooth...............................................................................................................................31
4.20.3 Phone Settings..........................................................................................................................31
4.20.4 Call settings..............................................................................................................................31
4.20.5 Network Settings...................................................................................................................... 33
4.20.6 Security Settings ......................................................................................................................33
4.20.7 Bluetooth..................................................................................................................................34
4.20.8 Restore Factory Settings ..........................................................................................................35
5 Operation Instructions on Chinese and English Input......................................................................35

4
6 Common Problems. .........................................................................................................................35
6.1 When the mobile phone displays “Insert SIM”? ........................................................................... 35
6.2 Checking and precautions of PIN, PIN2, PUK, PUK2 and password: .........................................36
6.3 Network connection fails ..............................................................................................................36
6.4 You can’t be heard.........................................................................................................................36
6.5 Can’t charge the battery ................................................................................................................36
6.6 Weak signal...................................................................................................................................36
6.7 Can’t make a call ..........................................................................................................................36
6.8 Standby time becomes short .........................................................................................................36
1 General Information
1.1 Brief
Thank you for selecting this series colored screen mobile phone.
Before installing and using the product, be sure to carefully read all the materials accompanying the mobile
phone. This will help you to better use the mobile phone, get an overall idea about the use, and understand the
perfect functions and the short-cut operating methods.
This colored screen mobile phone is designed for the GSM /GPRS network environment. In addition to the
basic call function, it also provides you many practical functions for your work and leisure, such as Dual Card
Mode , name card phone book, chord ring, clock/ alarm clock, Bluetooth , FM, calculator, games, Mp3 player,

5
Mp4 player, the mobile phone adopts the personalized human-machine interface and the perfect function
design can satisfy your different requirements.
*Note: Take the mobile phone as standard if the contents in this manual are different from those in your mobile
phone.
Our Company shall reserve all the rights to modify the content of the manual without any notice in advance.
1.2 Safety Precautions
If your mobile phone is lost or has bug, please inform the telecommunication department or the distributor to
prevent use of your mobile phone or SIM Card without authorization. Thus you avoid the economic loses
brought by the false phone call.
When you contact the telecommunication department or the distributors, they need to know the IMEI code of
your mobile phone (the label stickled on the back of your mobile phone. You can get it after pulling down the
battery). Please keep the code with care for future use.
Please adopt the preventive measures to avoid the misuse of the mobile phone, for instance:
-Properly set your mobile phone’s SIM card and the PIN code and change the codes on time before others know
them.
-When you leave your car, DO NOT leave your mobile phone at the place that is easily to be seen. You’d better
take it along with yourself or lock it in the luggage.
-Set up the call barring.
1.3 General precautions
Your mobile phone can only use the battery and charger specified by our Company. Any other products may
cause a battery leakage, overheat, burst or fire.
DO NOT impact, shake or toss your mobile phone violently so as to avoid the malfunction and fire occurring
to the mobile phone.
DO NOT leave your battery, mobile phone or charger in the oven or the high voltage equipment; otherwise,
accidents, such as circuit damage or a fire may take place to your mobile phone.
DO NOT use your mobile phone at the place with inflammable and explosive gases; otherwise, malfunction
and fire may take place to your mobile phone.
DO NOT place your mobile phone in the places with high temperatures or a great deal of dust; otherwise,
your mobile phone failure may happen.
Please leave your mobile phone at place out of the children’s reach, because the children may regard it as a
toy and cause physical injury.
DO NOT leave your mobile phone on uneven or unsteady surfaces so as to prevent it from falling, causing a
failure or a damage.
1.4 Precautions for mobile phone use
Please power off your mobile phone where mobile phone use is forbidden, e.g. on the plane or in the hospital.
The mobile phone may influence the normal working of the electronic equipment or the medical equipment.
In case of using the mobile phone at those places, please follow the relevant rules or regulations. The headset

6
has a time power on/off function and you are required to ensure that the mobile phone will never time power
on automatically during the course of the flight.
DO NOT use your mobile phone near the weak signal equipment or the highly sophisticated electronic
equipment. Radio wave interference may cause malfunction of the electronic equipment or other failures.
Attentions should be paid especially to the following equipment: hearing aid, pacemaker & other medical
electronic equipment, fire detector and other automatic control equipment. Please consult the equipment
manufacturer or the local distributor for the influence of the mobile phone to the pacemaker or other medical
electronic equipment.
DO not press the LCD screen or strike any other objects with it, otherwise, a damage and leakage may take
place to the LCD. If the liquid comes to your eyes, there will be a danger of blindness. In such a case, wash
your eyes with water (Note: DO NOT rub your eyes) and then go to the hospital for medical treatment.
DO NOT dissemble or remount your mobile phone; otherwise, a damage, creepage and circuit failure will be
likely to occur to your mobile phone.
In a few circumstances, when the mobile phone is used in the cars of some models, the electronic equipment
in the auto will affected by it. In such cases, DO NOT use your mobile phone so as to ensure the safety.
Please DO NOT press the keys with sharp things, such as needle or stylus; otherwise damage or mis-operation
may occur to the mobile phone.
If the antenna is damaged, DO NOT use your mobile phone; otherwise, it may cause a physical injury.
Keep the mobile phone far away from the magnetic objects, such as the magcard, for the radiation may clear
the information on the floppy disk, store value card and credit card.
Please keep the tiny things, such as thumb pin away from the handset of the mobile phone. During working
the speaker has magnetism, which may magnetize those tiny metal pieces and therefore causes a physical
injury to human or damage to the mobile phone.
Keep the mobile phone from wetting, for water and other liquids coming to your mobile phone may cause
overheat, leakage or malfunction to the mobile phone.
1.5 Precautions for battery usage
DO NOT throw the battery into the fire; or it may cause a fire and burst.
When installing the battery, DO NOT press the battery forcibly; or it may cause a leakage, overheat, burst or
fire.
DO NOT use the electric wire, needle or other metals to make a short circuit or do not leave the battery with
such metals as necklace; otherwise it may cause a battery leakage, overheat, burst or fire.
DO NOT weld the ends of the battery; or it may cause a leakage, overheat, burst or fire.
If the battery electrolyte enters the eyes, there is a possibility of blindness. In such case, DO NOT rub your
eyes. Please wash the eyes with clear water and then go to the hospital for medical treatment.
DO NOT dissemble or remount the battery or it may cause a leakage, overheat, burst or fire to your mobile
phone.
DO NOT use or place your mobile phone in the high-temperature places, such as by the side of the fire or the
heater; or it may cause a leakage, overheat, burst or a fire to your mobile phone.
If there is a temperature rise, color change or a deformation during the course of the usage, charging or
storage, please stop using the battery and change for a new battery.
If the battery electrolyte comes into contact with skin or clothes, it may cause the skin burnt. In such a case,
wash the skin and clothes immediately and then go to the hospital at once.

7
If the battery electrolyte leaks or sends off an odd smell, please take it away from the flammable fire so as to
avoid fire or burst.
Keep the battery from wetting; or it may cause overheat, smoke or erosion to the battery.
DO NOT use or keep the battery where the sunlight shoots from a right angle or near the car; or it may cause
overheat or leakage to the battery, which may lower the performances and shorten the service life of the
mobile phone.
DO NOT continuously charge the battery for more than 24 hours.
1.6 Precautions for usage of charger
Short circuit of the charger is forbidden; or it may cause an electric shock, smoke or damage to the charger.
DO NOT use the charger when the power supply wire is damaged; or it may cause a fire or an electric shock.
Please clean the accumulated dust covering the power socket.
DO NOT leave the water container near the charger so as to avoid water from spilling to cause overheat,
leakage or failure to the charger.
If the charger contacts water or any other liquids, pull out the power plug from the socket immediately so as
to avoid overheat, fire or failure to the charger.
DO NOT dissemble or remount the charger or it may cause a physical injury, an electric shock, a fire or
damage to the charger.
DO NOT use the charger in the bathroom or it may cause an electric shock, fire or charger to the charger.
DO NOT touch the charger, wire or power supply socket with a wet hand; or it may cause an electric shock.
DO NOT place the heavy object on the power supply wire or refit the wire; or it may cause an electric shock
or fire.
Before cleaning and maintenance, pull out the plug from the power supply socket.
Hold the charger when pulling out the plug from the socket, for pulling the cable may cause damage to the
wire, an electric shock or fir
1.7 Cleaning and Maintenance
The mobile phone, battery and charger have no waterproof performance, so please DO NOT use them in the
environment with a high temperature, such as bathroom, and avoid being damped by rain as well.
Please use the soft and dry cloth to clean the mobile phone, battery and charger.
DO NOT use solvents, such as alcohol, thinner or benzene to clean the mobile phone.
The plug with dirt is most likely to cause contact failure and power down so that the mobile phone can not be
recharged. Hence please clean the mobile phone regularly.
1.8 General Precautions
Mobile phone
Please use the mobile phone under the temperature ranging from 5°C to 40°C with a humidity ranging from
35% to 85%.
When using the mobile phone, keep as far as possible away from the general phone, TV，radio and office
automatic equipment so as to avoid affecting the normal performance of the equipment and the mobile phone.

8
Battery
The battery should be left in place where the sunlight shoots from indirect angles and the ventilation is good.
The service life of the battery is limited. The service time of the battery is shortened with the frequent
charging. When it is of no effect to charge for several times, it only means that the battery is exhausted and
the mobile phone should be replaced with a new battery of the specified mode.
DO NOT throw the old battery into the domestic rubbish. Dispose the exhausted battery according to
provisions specified by relevant authorities.
Charger
DO NOT charge the battery in the places where the sunlight shoots from right angles; the ambient
temperature is lower than 50C or higher than 400C; the place is damp or dusty or of too much vibration
(failure may occur); the location is near the electronic appliances, such as TV, radio etc.(image or sound may
be probably affected)
2 Before Use
2.1 SIM card
Before using the mobile phone, you should insert the valid SIM card, which is the key for you to enter the
GSM network.
All the information related to the creation of the connection to the network and initial call records will be recorded
in the metal plane area of the SIM card as well as the names, telephone numbers and SMS stored in the phone
book on the SIM card. The SIM card can be taken out from your mobile phone and can be placed in any one of the
GSM mobile phones for use (the new mobile phone will read the SIM card automatically).
To prevent losing and damaging of the information in the SIM card, please DO NOT touch the metal plane area
and the SIM card should be kept far away from electromagnetism. Once the SIM card is damaged, you can not
enter into the GSM network.
*Note: Please do power off your mobile phone before pulling out the SIM card. It is forbidden to insert or pull
out the SIM card with the mobile phone connected to the external power supply; otherwise, the SIM card is
most likely to be damaged.
2.1.1 Insert and pull out the SIM card
The SIM card is generally placed in a card. Before installation, take cautions to take out the SIM card.
Power off your mobile phone and then remove the battery and other external power supply.
Insert the SIM card into the SIM card slot.
When you need to pull out your SIM card, please power off your mobile phone firstly, remove the battery,
pull out your SIM card

9
2.2 Battery
The initial battery is of 50% charge, so it can be used right after being unpacked. The new battery should
be charged at least for 14 hours. Only when the initial battery is exhausted thoroughly (the electricity quantity
runs out and the mobile phone can not power on) can the battery be fully recharged for use, so does the
second time charging. Only when recycled for three times in this way can the battery works in the best
condition easily.
2.2.1 Charge the Battery
Connect the batter charger to a power supply;
Insert the plug of the battery charger into the right side of the mobile phone (note: with arrow face upwards).
Then the power quantity indicator in the upper right corner of the mobile phone screen will flicker. If the
phone has been powered off, the screen will display “charging” and this indicates that the battery is being
charged. If the phone is still in use despite of lack of power, the power indicator may take some time to appear
on the screen.
If the power indicator is full and stops to flicker, this means that the charge has been finished. This process
often takes 3 to 4 hours. It is normal that, during charge, the battery, mobile phone and battery charger
become hot.
After the charge is completed, please disconnect the AC power supply socket and the mobile phone with the
battery charger.
*Note:
--During the charge, the handset should be placed where the ventilation is good and the temperature is between
+50C to +400C. In addition, you should use the charger provided by the manufacturer, for the unauthenticated
chargers may cause danger and disobey the recognition and maintenance clauses of this mobile phone.
--When your mobile phone automatically powers off or displays the warning of “Low Power”, you should
charge the battery in time. In case the battery has not run out before charge, the mobile phone will shorten the
charge time automatically.
--The standby time and call time provided by the manufacturer is based on the ideal working environment.
During the practical use, the battery’s service time changes with the network condition, working environment
and use mode used.
--Before charging the battery, please make sure that the battery is properly inserted and it is forbidden to take it
down during charging. .
--When charge is over, please disconnect the charger with the mobile phone and the battery.
If you do not disconnect the charger with the power supply and the mobile phone, after a long time (about 5 to 8
hours), the power of the battery will drop to a certain level and the mobile phone will resume charge once again.
We do not recommend you to do so, for this will affect the performance and service life of the battery.
--This mobile phone does support USB port, so you can connect your mobile phone with PC through USB, it
just use to charging the battery.

10
2.3 Power on
Long press Hang Up key to power on the mobile phone and also long press the Hang Up key to power off
your mobile phone.
If you power on the mobile phone without inserting the SIM card, the mobile phone will prompt you to insert
the SIM card. After the SIM card is inserted, the mobile phone will automatically check whether the SIM card
is ready for use or not.
Then the screen will give the following prompts:
-Input PIN (If you have set password for SIM card) (Please refer to the section 4.20.6. “security settings”
for detail operations)
-Input the mobile phone’s password (if you have set the lock-code) (Please refer to the section 4.20.6.
“security settings” for detail operations)
When the SIM card is successfully decoded, the mobile phone will automatically search the available network
(the screen displays “search network”)
Once established connection, the name of the network supplier will appear on the top of the screen. This
means that the mobile phone is in “standby” mode and it is available for used.
*Note: If the screen prompts “Emergency”, this means that you are out of the normal network scope (service
scope), but you can still make the emergency call according to the signal intensity.
2.4 The use of USB data route
The method of using USB data route: Input one of the port into the computer, and then input the other port to the
phone, after that you can transfer the data between the computer and the phone. When you are charging, the icon
for the charge is moving. If the charging is finished, the icon will stop moving. You can use the phone as a U disk
after the phone power off.
The phone supports the USB, you can copy and move the file between the phone and the computer after you link
the USB with the computer. You can view the information in the T-Flash card.
*Note ：
--Please power off the phone before you connect the phone with the computer, after the phone connecting up,
you will find information of the USB on the computer, and then you can read the file into my computer. If there
is not information, you must check your phone’s USB port and insert it again.
--If you connect the phone with computer when the phone is powering on, there are three items displaying on
the phone, you should select the “mass storage”, and then you can copy or move the file between the phone and
the computer.
--After that, you need double click the USB icon in the right corner of the computer, and then select “stop”, now
you can withdraw the USB from the computer and the phone. DO not withdraw the USB from the computer
directly, or the date in the T-flash card will be lost, and it can also damage the phone.
You must do it on the computer which is the Windows2000 or SP2.
2.5 Install and pull out T-flash card
This mobile phone supports T-flash card, which is a kind of multimedia memory card used to increase memory of
the mobile phone. It is so small that you should take cautions to install or pull it out in order to avoid damage. The

11
method to install/ pull out T-flash card:
1. Power off the mobile phone, set memory card with the metal face downward to the memory card slot.
To pull out the memory card, power off the mobile phone, take out the T-flash.
*Note: The mobile phone does not support hot-plug function of T-FLASH in “power on” mode. Only when the
mobile phone is powered off can T-FLASH be pulled out. Restart up and T-FLASH will come into effect.
When using or editing files stored in the memory card, DO NOT pull out the memory card.
3 Basic Description
3.1 About the Keypads
3.1.1 Basic Keys
Left soft key: Dial and receive incoming call by using card 1; draw out dialed record in standby state.
Right soft key: Execute the function indicated on the bottom right screen.
Left function key: Enter main menu
Right function key: Open NYX Connect mail
Dial Key: Dial and receive incoming call
End key: End or reject a call; long press this key for Power on/off; under other circumstances: return to
standby mode.
Number key: Press number 0 to 9, sign *and # key to use make a call, input password.
3.1.2 Music Keys
Up music key: Volume up
Down music key: Volume down
Left music key: Pervious song
Right music key: Next song
Center music key: Play / Pause song
3.2 Call functions
When the logo of the network service provider appears on the screen, you then may make or answer a call.
The info bar implicates the signal intensity on the top left screen (the 4-scale info bar means the signal is the
strongest).
Call quality performs variedly under the influence of the obstacles. Therefore the movement in a small scope
may improve the signal intensity effectively.

12
3.2.1 Make a call
Domestic call:
You can input the telephone number via numeric keys to input the telephone number you want. Press the dial
key. If you need to change the telephone number, press the right soft key to delete the inputted characters.
During the dialing, the screen will display a “dialing” cartoon. The screen will display the call status
information. If the answering tone is switched on, there will be a warning tone.
When then call ends, please press Hand-up key to end the call.
Dial the extension to a fixed phone:
Because some of the extensions to the fixed phones can not be got through directly, you need to dial the
switchboard and then the extension to the fixed phone. When you input the telephone number, if insert
character “P” between the switchboard number and the extension number, the mobile phone will complete all
the dialing for you, i.e. automatically dial the extension and get through. Zone code+ switchboard number+ P
+ extension number + dial key
International call:
To make an international call, press “+”key until the international long distance call prefix symbol “+”appears
on the screen. This allows you dial in any country even if you do not know the local international call prefix.
After the prefix is input, enter the zone code of the country you want and the complete dial number. The zone
code is usually subject to conventions, 49 for Germany, 44 for U.K. and 46 for Sweden, etc.
Like dialing a long distance call, “0” in the city code should be dropped when dialing. E.g. To dial the service
hot line of other countries, you should dial: +86 21 114 +country code+ the complete dial number+ dial key
Emergency call
If your mobile phone is within the network coverage (you can check the network signal intensity bar on the
top left corner of the screen), you will be able to make an emergency call (the emergency call can be made
without the SIM card). If the network supplier provides no roaming service in the region, “Emergency Call”
will appear on the screen to tell you that you can only make this kind of calls.
3.2.2Answer a call
In a normal condition, when there is an incoming call, press the dial key to answer the call.
If the “any key for answer” is set on, then you can press any key to answer the call.
If the headset is inserted, you can also press the keys on the headset to answer a call. If it is not convenient,
you can activate “auto answer” and make sure that the handset is inserted. The call will be automatically got
through after two seconds’ ringing or vibration.
3.2.3 Reject a call
When there is an incoming call, press End key to reject the call.

13
3.2.4 Menu available during a call
During a call, you can press Option key to enter call menu. The call menu can only be seen during a call.
Besides, functions, such as call waiting, holding on a call, and multiparty meeting, need to be supported by
the network. Please contact with your network provider.
In the call menu, you can do the operations as follows:
Hold call: hold on the current call or restore the held call.
End call: end the current call.
New call: make a new call.
Phonebook: enter the phone book menu.
Messages:enter the Message menu.
Mute: do not send/ restore sending of local voice.
DTMF: Enable or disable DTMF (dual-tone multi-frequency).
Swap: switch the holder with activator
Conference: start a telephone meeting.
Transfer: transfer current call to another mobile phone.
Sound recorder: record the call voice.
*Note. Some of the menus only appear in the specific circumstances, e.g. “Swap” only appears “during a call”
and “hang up” call.
3.3 Hand-free function
When you make a call, press the Right Soft Key to have a Hand-Free function.
4 Menu Introduction
4.1 Phone book
You may make full use of phone book to store some name, mobile phone number, family number, company
number and so on. Please choose “phone book” from main menu, and then enter it.
------Quick search: choose this option to enter into the phone book browse interface. On the lower part of the
screen there is a search box, and you can input relevant information to filter the telephone record. You can press
“#” to switch the search method.
* Note: You can save up to 500 telephone numbers in mobile phone and 200 numbers in SIM1 and SIM2
(depends on the capacity of SIM card).
You can see the following options in phone book detailed:
View: view the details of the contact.
Send text message: edit text message and send it to this number.
Send multimedia message: edit multimedia message and send it to this number.

14
Call: call this number.
Edit: edit this number and then save it to phone book.
Delete: choose this function to delete the contact.
Copy: Copy the contact.
Move: Move the contact.
Send contact: Send contact as text message; Send contact as multimedia message; Send contact via Bluetooth.
Add to Blacklist: Add this contact to Blacklist.
Mark several: Select one or more numbers , and Mark.
Mark
Unmark: Unmark of numbers.
Send text message: Edit text message and send it to the mark numbers.
Delete marked: Delete marked of numbers.
Mark all: Mark all of numbers.
Umark all: Unmark all of numbers.
Mark all
Unmark: Unmark of numbers.
Send text message: Edit text message and send it to this number.
Delete marked: Delete marked of numbers.
Umark all: Unmark all of numbers.
Caller groups: The mobile phone provides you with five incoming groups. You can change the group name,
call ring, incoming picture to every group; or add or delete the group member.
Phonebook settings:
------Preferred storage: choose the priority for the storage location- the mobile phone or SIM1 / SIM 2 orAll.
------Speed dial: set quick dial. In standby interface, press and hold corresponding number key and you can call the
specified number.
------My number: Choose this option to edit or transfer detailed data of the record user.
------vCard version: Select vCard version.
------Extra numbers: the numbers stored in the SIM 1 or SIM 2, e.g. the number of this mobile phone, service
number, which you can check and modify.
------Memory status: Choose this option to check the phonebook information in the SIM card and in the mobile
phone
------Copy contacts: copy all the records in the mobile phone or the SIM card (SIM1 or SIM 2): both SIM card to
mobile phone and phone to SIM card are workable.
------Move contacts: move all the records in the mobile phone or the SIM card (SIM1 or SIM 2): both SIM card to
mobile phone and phone to SIM card are workable
------Delete all contacts: choose this function to delete phone record all from SIM card (SIM1 or SIM 2) or mobile
phone. One by one delete available too( note: must enter password to delete all when deleting phone number
in SIM card and this mobile phone, default password is 1122)
------Phone Book Backup: choose this function to Backup of phonebook.

15
4.2 Messaging
The message services can only be used if they are supported by your network or your service provider and
you have subscribed to them. Also appropriate settings need to be in place.
*Note: When sending messages, your phone may display the words Message sent. This is an indication that the
message has been sent by your device to the message centre number programmed into your device. This is not
an indication that the message has been received at the intended destination. For more details about messaging
services, check with your service provider.
4.2.1 NYX Connect Mail
User can use push mail service on their email accounts via NYX Connect Mail. It is strongly recommend user to
insert memory card before using push mail service. User can add their email account(s) with push mail service.
4.2.2 NYX Messenger
User can use the NYX PIN messenger to communicate with other NYX messenger friends; and also user can
connect to their Facebook chat service to chat with Facebook friends.
4.2.3 Write message
Write Message: access submenu “Write Message” to input short message.
------Send to: send the message with SIM1 or SIM2. Choose this option to access recipient edit box, and you can
press number keys to input telephone number or press Search to bring out Contacts and choose a number
and then press OK to send.
------Input method: Change the input method when editing message.
------Insert: insert preset message, Idiograph, Business card, template, object and bookmark into the message.
------Schedule send: Edit message and number, send this message in appoint time and date(By SIM1 or SIM2).
------Save to Drafts: Not send this message, just store it. (By SIM1 or SIM2).
* Note: Short message centers in some cities and areas don’t support long short messages of more than 160
English characters.
4.2.4 Inbox
View received messages of SIM1 or SIM2. When the messages list of Inbox appears, you can press OK to
read the message. You can press Option to perform the following operations.
------Reply: reply the sender with SIM1 or SIM2.
------ Call sender: call the number of the sender.
------Forward: forward this message with SIM1 or SIM2.
------Delete: delete this message.

16
------ Use number: pick up the numbers with 3 or more digits in the messages. You can call these numbers,
send message to them, or save them in Contacts.
------Advanced
Use URL: pick up the web address in the message and connect to it.
Use USSD: pick up the numbers with 1 or 2 digits in the messages.
Copy to phone/SIM: copy this message to phone or SIM card.
Move to phone/SIM: move this message to phone or SIM card.
Press Option to perform the following operations.
------View: View the details of the message.
------Reply: reply the sender with SIM1 or SIM2.
------ Call sender: call the number of the sender.
------Forward: forward this message with SIM1 or SIM2.
------Delete: delete this message.
------Delete all: delete all the messages in Inbox.
------Save to Phonebook: Choose the number of the message to Phonebook.
------Mark several: Select one or more messages to be labeled
Mark: Press OK to mark the message. You can press Option to perform the following operations.
Delete: delete the message marked.
Copy to phone/SIM: copy the message marked to mobile phone or SIM card.
Move to phone/SIM: move the message marked to mobile phone or SIM card.
Unmark: cancel the message marked.
Mark all: Select all messages to be labeled.
Unmark all: cancel all messages to be labeled.
Mark all: select all messages to be labeled.
Delete: delete the message marked.
Unmark: cancel the message to be labeled.
Unmark all: cancel all messages to be labeled.
------Advanced:
Copy to phone/SIM: copy this message to mobile phone or SIM card.
Move to phone/SIM: move this message to mobile phone or SIM card.
Copy all: copy all the messages saved in SIM card or mobile phone.
Move all: move all the messages saved in SIM card or mobile phone.
------Delete same number message: Delete all message with same number.
------Add to sms black list: Add the number to message black list.
4.2.5 Drafts
Save messages which will be sent later. When the messages list of Drafts appears, you can press OK to read
the message. You can press Option to perform the following operations:
------ Send: send the message with SIM1 or SIM2.
------ Edit: pick up and edit the contents of the message.
------ Delete: delete the message.
------Advanced:
Use number: pick up the numbers with 3 or more digits in the messages. You can call these numbers,

17
send message to them, or save them in Contacts.
Use URL: pick up the web address in the message and connect to it.
Use USSD: pick up the numbers with 1 or 2 digits in the messages.
Copy to SIM / phone: copy this message to mobile phone or SIM card.
Move to SIM / phone: move this message to mobile phone or SIM card.
Press Option to perform the following operations.
------View: View the details of the message.
------Send: add contact send this message.
------Edit: pick up and edit the contents of the message.
------Delete: delete the message.
------Delete all: delete all the messages in Drafts.
------Mark several: Select one or more messages, and mark.
Mark: Press OK to mark the message. You can press Option to perform the following operations
Delete: delete the message marked.
Copy to phone/SIM: copy the message marked to mobile phone or SIM card.
Move to phone/SIM: move the message marked to mobile phone or SIM card.
Unmark: cancel the message marked.
Mark all: Select all messages to be labeled.
Unmark all: cancel all messages to be labeled.
Mark all: select all messages to be labeled.
Delete: delete the mark message.
Unmark: cancel the message marked.
Unmark all: cancel all messages to be labeled.
------Advanced:
Copy to phone/SIM: copy this message to mobile phone or SIM card.
Move to phone/SIM: move this message to mobile phone or SIM card.
Copy all: copy all the messages saved in SIM card or mobile phone.
Move all: move all the messages saved in SIM card or mobile phone.
4.2.6 Outbox
View sent messages of SIM1 or SIM2. When the messages list in Outbox appears.
You can press OK to read the messages. You can press Option to perform the following operations:
------Forward: forward this message with SIM1 or SIM2.
------Delete: delete the message.
------Delete all: delete all the messages in Outbox.
------ Advanced:
Use number: pick up the numbers with 3 or more digits in the messages. You can call these numbers,
send message to them, or save them in Contacts.
Use URL: pick up the web address in the message and connect to it.
Use USSD: pick up the numbers with 1 or 2 digits in the messages.
Copy to SIM / phone: copy this message to mobile phone or SIM card.
Move to SIM / phone: move this message to mobile phone or SIM card.

18
Press Option to perform the following operations.
------View: View the details of the message.
------Forward: forward this message with SIM1 or SIM2.
------Delete: delete the message.
------Delete all: delete all the messages in Drafts.
------Mark several: Select one or more messages to be labeled.
Mark: Press OK to mark the message. You can press Option to perform the following operations
Delete: delete the mark message.
Copy to phone/SIM: copy the mark message to mobile phone or SIM card.
Move to phone/SIM: move the mark message to mobile phone or SIM card.
Unmark: cancel the message marked.
Mark all: Select all messages to be labeled.
Unmark all: cancel all messages to be labeled.
Mark all: select all messages to be labeled.
Delete: delete the message marked.
Unmark: cancel the message marked.
Unmark all: cancel all messages to be labeled.
------Advanced:
Copy to phone/SIM: copy this message to mobile phone or SIM card.
Move to phone/SIM: move this message to mobile phone or SIM card.
Copy all: copy all the messages saved in SIM card or mobile phone.
Move all: move all the messages saved in SIM card or mobile phone.
4.2.7 MMS
MMS includes text, picture and audio. With Multimedia Messaging Service (MMS), you can not only send or
receive pictures and text, but also receive the audio files attached in the message and enjoy its abundant contents.
With color screen, MMS brings you bright color and vivid A/V experience.
This mobile phone supports receiving and sending MMS up to 97KB and can’t receive those beyond this
limitation.
It supports MMS of multiple pages, i.e. each page contains a picture, a piece of music and text, and the MMS
is made up of several pages of this type. If the MMS contains picture, the mobile phone will adjust the picture
automatically to make it displayed on the screen.
* Note: This function needs to be supported by network operator.
Write Message: Create a new multimedia message. You need to input the Recipient, Cc, Bcc, Subject and
Content.
Inbox: view received multimedia messages. (The operation is same as Inbox of SMS)
------ View: view the multimedia message.
------ Reply: reply to sender in MMS.
------ Reply by SMS: reply to sender in MMS.
------ Reply all: reply all the senders in MMS.
------ Forward: forward the multimedia message to other recipients.
------ Delete: delete this multimedia message.

19
------ Delete all: delete all messages in Inbox.
------ Properties: view details of the multimedia message, including Sender, Subject, Date, Time and Size.
------ Use details: pick up numbers with 3 or more digits and the web address in the multimedia message.
You can call the numbers or save them in Contacts, and access the web address.
Outbox: Save multimedia messages that haven’t been sent. (The operation is same as Outbox of SMS)
------ View: view the multimedia message.
------ Forward: forward the multimedia message to other recipients.
------ Edit: edit the multimedia message.
------ Delete: delete this multimedia message.
------ Delete all: delete all multimedia messages in Outbox.
------ Properties: view details of the multimedia message, including Recipient, Date, Time and Size.
------ Use details: pick up numbers with 3 or more digits and the web address in the multimedia message.
You can call the numbers or save them in Contacts, and access the web address.
Drafts: Save multimedia messages which will be sent later. The messages are saved in Outbox after sending.
------ View: view the multimedia message.
------ Send: send the multimedia message.
------ Edit: edit the multimedia message.
------ Delete: delete this multimedia message.
------ Delete all: delete all multimedia messages in Drafts.
------ Properties: view details of the multimedia message, including Recipient, Date, Time and Size.
------ Use details: pick up numbers with 3 or more digits and the web address in the multimedia message.
You can call the numbers or save them in Contacts, and access the web address.
Templates: default multimedia messages. access Template and view or send the multimedia message.
MMS Settings: set the parameters of sending and receiving multimedia message.
------ Profiles: select or edit MMS server according to network operator.
------ Common settings:
Compose: enable this function and only the pictures and ring tone that accord with MMS specification
can be sent.
Send: set the parameters of sending multimedia message. For example: Validity, Sending Report,
Reading Report, Priority, Interval, Sending Time, etc.
Retrieve: set the parameters of receiving multimedia message. For example: home network, roaming
network, send reading report, allow sending report, etc.
Filter: filtrate multimedia message.
Memory Status: check the status of mobile phone memory.
4.2.8 Broadcast Message
SIM1 broadcast message
Receive and read the messages from SIM1 Cell Broadcast. The functions are as follows:
------ Receive mode: enable/disable receiving cell broadcast.
------ Read message: read the messages you have received from Cell Broadcast.
------ Languages: select language.
------Channel settings: Set the channel of cell broadcast, including Select, New, Edit and Delete.
SIM2 broadcast message

20
Receive and read the messages from SIM2 Cell Broadcast. The functions are as follows:
------ Receive mode: enable/disable receiving cell broadcast.
------ Read message: read the messages you have received from Cell Broadcast.
------ Languages: select language.
------ Channel setting: Set the channel of cell broadcast, including Select, New, Edit and Delete.
* Note: In Messaging, if you select “SIM1 only”, only items that relate to SIM1 are displayed, e.g. Voicemail,
Cell Broadcast; if you select “SIM2 only”, only items that relate to SIM2 are displayed, e.g. SIM2 Voicemail,
SIM2 Cell Broadcast., This function needs to be supported by network operator.
4.2.9 Templates
Templates: Common phrases can be applied in the frequently used information to avoid repeated input
when the message is to be sent. They can be edited or deleted.
4.2.10 SMS settings
SIM1 message settings: perform the following settings to SIM1:
------Idiograph: edit name and set the auto ideograph is on/off.
------Schedule send: Edit message and number, send this message in appoint time and date(By SIM1 or
SIM2).
------Profile Setting: select a suitable mode for mobile phone short message. Access the mode and you can set
the name, SMS center number, validity and sending format.
------voicemail server
The functions of Voicemail are as follows:
Edit: set the name and telephone number of SIM2 voicemail.
Call voice mail: dial and connect to Voicemail.
------Common Settings: set whether enable message report or reply path.
------ Memory status: view the status of SIM1 or mobile phone memory.
------Preferred Storage: save messages in mobile phone or SIM1.
SIM2 message settings: perform the following settings to SIM2:
------Idiograph: edit name and set the auto ideograph is on/off.
------Schedule send: Edit message and number, send this message in appoint time and date(By SIM1 or
SIM2).
------Profile Setting: select a suitable mode for mobile phone short message. Access the mode and you can set
the name, SMS center number, validity and sending format.
------voicemail server
The functions of Voicemail are as follows:
Edit: set the name and telephone number of SIM2 voicemail.
Call voice mail: dial and connect to Voicemail.
------Common Settings: set whether enable message report or reply path.
------ Memory status: view the status of SIM1 or mobile phone memory.
------Preferred Storage: save messages in mobile phone or SIM2.
Black List: switch on/off blacklist mode and edit some blacklist numbers.