ItsaGoal MINI-RUGBY GOAL Install guide

FITTING
INSTRUCTION
- Two section crossbar
COMPONENTS
POST SECTIONS
68mm
2
2
x
x
CROSSBAR SECTION
UPRIGHT SECTION
865mm LONG - 68mm Diameter
F
G
68mm
MINI-RUGBY GOAL
TEL: [phone]SPARE PARTS
68mm
2
x
UPRIGHT SECTION
2031mm LONG - 68mm Diameter
H
2
x
UPRIGHT SECTION
I68mm
2
x
STEEL GROUND ANCHOR
A
LARGE QUICK RELEASE
E6
x
2
x
BLANKING CAP
B
3
x
STRAIGHT CONNECTOR
D
2
x
‘T’ BRACKET
C
This rugby post can be
assemble to make
different sizes of
cross bar height to
suit different age groups.
I I
H
H
G
G
F
F
1 2
ALUMINIUM
OPTIONAL
If you intend to install your posts and
leave them in-situ throughout the year we
strongly advise to buy the optional
aluminium uprights. The uPVC uprights
supplied with this goal should not be
used in high winds.
NOTE : All plastic extrusions
vary and therefore some tubes
may be looser or tighter to
connector fittings. If you want to
increase the diameter of the
fitting just wrap masking tape
around the part that fits into the
tube, twist as you insert the
fitting and it will grab to the
tube tight ...you can make
tighter fits by adding more tape.
H
G
I
I
H
G
D
C
A
A
D
F
F
C
D
1.72m to under crossbar or 2.59m to crossbar
or for older children 3.75m to under crossbar
Total post height 4.72m
UPRIGHT POSTS
ALWAYS USE A PROTECTIVE PIECE OF WOOD
(NOT INCLUDED) BEFORE HAMMERING THE
TOP OF THE METAL SPIKE.
Protective
Wood
This will protect the metal
anchor spike and prevent the
top becoming miss shapen. If
the metal spike becomes
misshapen this can cause
upright posts to split and this
would not be covered under
the guarantee.
ADD TAPE
Around metal
anchor To
protect posts.
Tape Not
included
SLIDE POST
OVER ANCHOR
STEEL GROUND ANCHORS
HAMMER FULL DOWN INTO THE GROUND
1. Make sure the Steel Ground Anchor is
In line square with the posts and hammer
fully into the ground.
Note : If the ground is hard it is advisable to wet the ground and make a starting hole with
a metal pole before hammering the ground anchor into the ground. Damage cause in this
way will invalidate your warranty.
2. To remove from ground tap lightly and wiggle
left to right and lift up. This should leave
the ground undisturbed.
TAP
LIGHTLY
WITH
HAMMER
LIFT
UP
!
WORLDWIDE © COPYRIGHT 2016 ITSA GOAL POSTS LTD, ALL RIGHTS RESERVED A REGISTERED.
WE RESERVE THE RIGHTS TO AMEND THE SPECIFICATIONS OF OUR SOCCER PRODUCTS IN THE
INTEREST OF CONTINUED DEVELOPMENT. YOUR PRODUCT THEREFORE MAY DIFFER SLIGHTLY
TO THOSE ILLUSTRATED. E&OE

NOTE: Goal must be anchored otherwise breakages may occur. In extreme
conditions it is advised to store away. Do not drop heavy objects on to the plastic
tubes.
The posts can be washed with hot soapy water. Any scuff marks on posts can be
rubbed off with a light abrasive scouring pad.
WARNING: Check the position of any underground services before using the
ground anchors and pegs. We take no responsibility for any damage or injury
caused in this manner.
NEVER use the goals without the ground anchor system. In severe weather or
windy conditions it is advisable to take your goal down as damage is not covered
by the guarantee in such circumstances.
It is advisable in any contact sport to take out the relevant insurance's to cover
against injury both from taking part, equipment and other unforeseeable
circumstances.
Crossbars will not be replaced within the guarantee period if broken by swinging or
climbing or any other misuse.
DO NOT try to glue any damaged fixings, plastic materials in this product vary and
this may cause the plastic to break. Always replace any damaged components.
SPARE PARTS ARE AVAILABLE
We advise adult supervision during assembly and use. Do not use any
component parts if they are damaged or broken. Spare parts and replacement
nets are readily available.
Hard surfaces: to prevent damage to goal or it's components, loosen soil with a
steel pole and moisten with some water before inserting the ground anchors. Do
not use the goal in sub zero temperatures. Damaged components requested
under guarantee must be returned for inspection. Failure to follow the warnings,
fitting instructions contained in this document, may invalidate your guarantee.
The company , its agents and representatives do not accept any product liability
if used outside the EU. Use of the product in other countries outside the EU
including the USA is not covered and appropriate insurance should be taken out
by the user to cover for any eventuality.
We reserve the rights to amend the specifications of our soccer products in the
interest of continued development. Your product therefore may differ slightly to
those illustrated. Not suitable for children under 36 months until assembled due
to small parts.
CROSSBARS WILL NOT BE REPLACED
WITHIN THE GUARANTEE PERIOD IF
BROKEN BY SWINGING OR
CLIMBING OR ANY OTHER MISUSE.
DO NOT TOUCH OVERHEAD SERVICES
WITH GOALPOST SECTIONS. CHECK
THE POSITION OF ANY OVERHEAD
SERVICES WHEN SETTING UP OR
DISMANTLING THE GOALS, EG. POWER
LINES, TELEPHONE CABELS ETC.
BEFORE YOU START TO ASSEMBLE YOUR GOAL PREPARE THESE FIRST.
‘T’ BRACKETS
!
BPush and Lock the
Blanking Caps in the
‘T’ Brackets.
2
Push and Lock the
Large Quick Release
Buttons into the ends
of the ‘T’ Brackets.
1
E
TEL [phone]
GOAL LINE
1
Lay the Crossbar
Section along the goal
line to give you the
correct position to insert
the Steel Ground
Anchors and the
distance between them
(steps 1-2).
FRONT GROUND ANCHOR POSITIONS
2
C
The Steel Ground
Anchors need to be
sunk into the ground.
You will need to
hammer the Steel
Ground Anchor.
Using either a mallet
or hammer (step 3).
When the Ground
Anchor is in position
you can now slide the
Uprights onto the
anchors (step 4).
4
I
GAS
WATER
CHECK THE POSITION OF ANY
UNDERGROUND SERVICES
CHECK THE POSITION OF ANY UNDERGROUND
SERVICES BEFORE USING THE GROUND SPIKES
AND PEGS. WE TAKE NO RESPONSIBILITY FOR
ANY DAMAGE OR INJURY CAUSED IN THIS
MANNER. OUR GROUND ANCHOR SYSTEM IS
DESIGNED TO GIVE SLIGHTLY UNDER HEAVY
IMPACT TO HELP PREVENT SERIOUS INJURY. TO
LOOSEN TAP SIDES OF SPIKE WITH HAMMER
BEFORE EXTRACTING.
Protective
Wood
3
MALLET
12
3
Radius 100mm
45
40mm min.
500mm
o
45 max.
1 Ground Anchor 2 Sport Surface 3 Concrete Block
4 Ground Socket 5 Drainage Hole
OPTIONAL EXTRA GROUND SOCKET
N O T E : A sp a c e r c a n b e p u t i n s i d e so c k e t s t o
l i f t t h e g o a l i f it i s too low or lopsided.
When the posts are anchored in the same position
regularly the ground may become worn. It is possible
to concrete ground sockets in position. Concrete the
sockets in position following separate ground socket
instructions. Pour sand and clay inside the socket.
The front ground anchor can be inserted into the
clay/sand within the ground socket.
PLASTIC
FRONT
GROUND
SOCKET (2)
METAL FRONT
GROUND
CONCRTE
SAND &
CLAY
INSIDE
SOCKET
FRONT
GROUND
SOCKET
CAPS (2)
SOCKET WITH FRONT
GROUND SOCKET CAP
WORLDWIDE © COPYRIGHT 2016 ITSA GOAL POSTS LTD, ALL RIGHTS RESERVED A REGISTERED DESIGN.
WE RESERVE THE RIGHTS TO AMEND THE SPECIFICATIONS OF OUR SOCCER PRODUCTS IN THE INTEREST OF CONTINUED DEVELOPMENT. YOUR PRODUCT THEREFORE MAY DIFFER SLIGHTLY TO THOSE ILLUSTRATED. E&OE