ItsaGoal 16' X 7' YOUTH GOAL User manual

ALUMINIUM
80
mm
FLAT-PACK
CARE & MAINTENANCE - see separate sheet supplied or visit www.itsagoal.net for additional copies.
Our goalpost if used correctly will last many years. We do also offer a full spare part service and if your goals
need refurbishment this can be arranged.
16' X 7' YOUTH GOAL (16' x 7' Multi-Surface) - One section crossbar.
E
E
UC
RC
RC
RC
RC
B
B
P
Q
F
R
O
J
D
G
J
J
J
J
J
K
N
2
2
2
2
1
1
x
x
x
x
x
x
CROSSBAR SECTION
4844mm LONG 80mm Diameter
BACKBAR SECTION
4844mm LONG 80mm Diameter
SIDEBAR SECTION
1726mm LONG 80mm Diameter
UPRIGHT SECTION
2031mm LONG 80mm Diameter
TOP STANCHION TUBE
630mm LONG 40mm Diameter
BACK STANCHION TUBE
2232mm LONG 40mm Diameter
POST SECTIONS
M
M
N
O
P
Q
R
Aluminium Sections and Tubes
COMPONENTS
6
2
x
x
MULTI-SURFACE ANCHOR
GROUND PEG
NYLON STANCHION ELBOW
D
E
F
4
x
NYLON SPIGOT
B
NYLON LOWER BACK STANCHION
CONNECTOR
G2
x
J12
x
12
x
8
x
K
8mm
NYLON
NYLON
1
x
GOAL NET 16' x 7'
NET
1
x
AK
M10 SOCKET DOME SCREW AND
HEX DOME NUT - 75mm LONG
M8 HEX SCREW AND HEX DOME NUT -
50mm LONG
HEX KEY
FOR COMPONENT J
I
M
40
12
x
x
LARGE NET TIES - ground frame
SMALL STANCHION NET TIES
10mm
4
2
x
x
CORNER BRACKET
UPRIGHT CORNER BRACKET with
attached 4 x FLANGED BUSHES
RC
UC
60
x
SLOT NET FIXINGS
FXB
40mm
40mm
80mm
80mm
80mm
80mm
FITTING GOALPOST SLOT NET FIXINGS
Twist 90 degrees to secure.
Position the fixings no more
than 340mm apart.
Fit into groove on goalpost section.
1 2
FXB
RC
B
UC
RC
G
B
K
UPRIGHT CORNER BRACKET
FLANGED
BUSHES
INSERTED X 4
CORNER BRACKET
GOAL POSTS MUST BE ANCHORED AT ALL TIMES
Optional longer pegs are available for use on sandy ground. On grass, a risk
assessment of soil and weather conditions suitability should be carried out
when anchors or optional counter weights are to be used. TEL: [phone]
Visit our YouTube site for assembly videos :
www.youtube.com/user/Footballgoalposts
Goalpost spare parts and replacement nets are available at - www.itsagoal.co.uk
WE RESERVE THE RIGHTS TO AMEND THE SPECIFICATIONS OF OUR SOCCER PRODUCTS IN THE INTEREST OF
CONTINUED DEVELOPMENT. YOUR PRODUCT THEREFORE MAY DIFFER LIGHTLY TO THOSE ILLUSTRATED. E&OE
VISIT THE WEB SITE WWW.ITSAGOAL.NET TO REGISTER UK GOALPOST WARRANTY
WORLDWIDE © COPYRIGHT 2022 ITSA GOAL POSTS LTD, ALL RIGHTS RESERVED A REGISTERED DESIGN
FITTING
INSTRUCTION
TEL: [phone]
SPARE PARTS
N

STEP BY STEP FITTING
STEP 1
Lay out and check all posts shown below
Also check you have all the
components.
STEP 2
Insert spigot B into corner
bracket RC (x 4)
STEP 3
Using two of the corner brackets from step 2,
Insert Lower back stanchion connector G
into the spigot B,
fix with net and
bolt K (x 2)
STEP 4
Insert upright corner bracket UC into side sections O,
fix with nut and bolt J. Insert the corner bracket RC
with the insert spigot B and lower back stanchion
connector into the side section O. Connect the back
bar section, bolt both ends with K.
STEP 5
With the ground base assembled now insert
the upright posts P into the upright corner
brackets UC and Bolt with J, support the
uprights from falling with a second person
until you have the remaining crossbar and
back supports fitted in step 6 & 7.
STEP 6
Connect the corner brackets RC into the
crossbar M with the nuts and bolt J.
Insert the crossbar with fitted corner
brackets RC into the upright posts.
STEP 7
Fit the nylon stanchion elbow F into
the top stanchion tube Q
and also the back tube stanchion R,
connect with nuts and bolts K.
With the full back stanchion assembled
insert it into the corner bracket with fitted
spigot at the top of the upright.
and the lower back stanchion
connector G
STEP 8
Insert all net fixings
& fit the net - see over page
QR
RCRC
BB
RC
G
K
O
O
UC
UC
UC
RC
RC
UC
N
O
O
P
P
M
RC
RC
J
J
Q
R
F
G
R
Twist 90 degrees to secure.
Position the fixings no more
than 340mm apart.
Fit into groove on goalpost section.
1
2
FXB
FITTING GOALPOST SLOT NET FIXINGS
Visit our YouTube site for assembly videos :
www.youtube.com/user/Footballgoalposts WE RESERVE THE RIGHTS TO AMEND THE SPECIFICATIONS OF OUR SOCCER PRODUCTS IN THE INTEREST OF
CONTINUED DEVELOPMENT. YOUR PRODUCT THEREFORE MAY DIFFER LIGHTLY TO THOSE ILLUSTRATED. E&OE
Support
uprights
Support
uprights
Support
uprights
Support
uprights
2
2
2
1
1
x
x
x
x
x
CROSSBAR SECTION
4844mm LONG 80mm Diameter
BACKBAR SECTION
4844mm LONG 80mm Diameter
SIDEBAR SECTION
1726mm LONG 80mm Diameter
UPRIGHT SECTION
2031mm LONG 80mm Diameter
M
N
O
P
TOP STANCHION TUBE
630mm LONG 40mm Diameter
2
x
BACK STANCHION TUBE
2232mm LONG 40mm Diameter
N

STEP BY STEP NET FITTING
STEP 1
Open net and check the lengths of a and b
correspond with the diagram below.
STEP 4
Using the small net ties attach the net
down the back of the sloping
back net supports (optional)
as shown to the posts
as shown.
a
b
a
b
NET
CHORD
OPTIONAL - STANCHION TIES
A net fixing that works on most aluminum goalposts that have
a slot on the rear of the posts. This net fixing can be left in
place in the slot on the goal extrusion or can be twisted out
and left attached in position on the net.
To attached the net turn the net fixing upside down and lay it
into the slot with the opening facing up. Do this with goal post
extrusion laid on the ground. The two lugs on the top of the
fixing will hold the fixing clip firmly in the goalpost slot upside
down to enable the net to be pushed through the opening on
the back of the fixing.
This is a unique design feature that makes it easier to insert
the net inside the fixing compared to other similar types of net
fittings. Much easier to fit than other similar net fixings.
Goalpost Slot Net Fixing
Fitting Instructions
MADE IN ENGLAND www.itsagoal.co.uk
3
Twist 90 degrees to secure.
Position the fixings no more
than 340mm apart.
78
Fit into groove on goalpost section.
6Once net fixings have net cord
inside twist round to insert into
the slot on the goalpost extrusion
4
1
Lugs hold
the fixings
in the channel
whilst you push
the net cord inside
5
2
STEP 2
With the net the correct way round lift the net onto the
goalpost frame.This is easier with two people.
 NOTE: If your net does not fit the first
time, you may be fitting it to the goal
frame upside down i.e. that is to say the
net from the crossbar to the floor (a) is
longer than the length of the net to the
bottom of the upright.(b)
STEP 3
Attach the corners first, where the
upright posts meets the crossbar as
shown. Then attach the net to the
post using the net fixings
STEP 5
To help define the roof of the net Tie the cord to one
side and pull the net chord tight and wrap neatly down
and around the stanchion section. If you are regularly
attaching or detaching the net then apply coloured tape
to the roof corners of net to help identify the roof area.
ANCHORING YOUR GOAL
WARNING: Check the position of any underground services before using the ground anchors and pegs. We take no responsibility for any damage or injury caused in this manner.
HARD SURFACES: to prevent damage to goal or it's components, loosen soil with a steel pole and moisten with some water before inserting the ground anchors. Do not use the goal in
sub zero temperatures. ANCHORING YOUR GOAL ON GRASS - POSITION YOUR GOAL ON A LEVEL PLAYING SURFACE. PLACE THE MULTI-SURFACE ANCHOR OVER EACH SIDE OF THE
GROUND FRAME (POSITIONS SHOWN) HAMMER THE PEGS THROUGH THE HOLES (DO NOT USE METAL HAMMERS USE RUBBER MALLETS) ON THE ANCHOR DOWN UNDER THE
FRAME INTO THE GRASS ADDITIONAL ANCHORS OR LARGER PEGS CAN BE PURCHASED FOR USE ON SOFT GROUND OR SAND. THESE ANCHORS CAN BE USED FOR HARD
SURFACES SUCH AS TARMAC WITH OPTIONAL BOLTS. ON HOT/SUNNY DAYS TARMACADAM SOFTENS AND THEREFORE TO ANCHOR
YOUR GOAL PROPERLY YOU MUST:- 1 DIG HOLES IN YOUR TARMAC FILL HOLES WITH CONCRETE , 2 DRILL TWO 14MM HOLES 12CM APART AND 70MM DEPTH.
3 POSITION GOAL AND ANCHOR, INSERT AND TIGHTEN BOLT. FOR OTHER SURFACES SUCH AS WOODEN SPORTS HALL FLOORS WOOD SCREWS (INSTEAD OF BOLTS) OR
COUNTER BALANCE WEIGHTS CAN ALSO BE USED (SUPPLIED SEPARATELY).
9
10
GROUND
PEG REMOVAL
D
E
USE THE HOOK ON THE END
OF THE RED GROUND PEG
TO REMOVE PEGS FROM THE GROUND OR USE
A CLAW HAMMER FOR PEGS THAT ARE
DIFFICULT TO REMOVE.
INSERT MULTI-SURFACE
ANCHOR PEGS FULLY
GROUND
FRAME
WASHER
DRILL HOLES
2 x MULTI SURFACE
ANCHORS
M10 SLEEVE
ANCHOR
RAWBOLT
12cm(min)
30cm
12.3cm
18cm
12cm
(minimum)
30cm
12.3cm
18cm
THIS METHOD SECURELY ANCHORS
YOUR GOAL DOWN ON TARMAC
DO NOT OVER TIGHTEN BOLT.
CONCRETE BLOCK
(FOR USE ON
TARMAC)
GROUND
FRAME
WASHER
DRILL HOLES
2 x MULTI SURFACE
ANCHORS
M10 SLEEVE
ANCHOR
RAWBOLT
12cm(min)
30cm
12.3cm
18cm
12cm
(minimum)
30cm
12.3cm
18cm
THIS METHOD SECURELY ANCHORS
YOUR GOAL DOWN ON TARMAC
DO NOT OVER TIGHTEN BOLT.
CONCRETE BLOCK
(FOR USE ON
TARMAC)
LONGER GROUND PEGS ARE AVAILABLE SEPARATELY.
200mm
STANDARD
300mm
SOFTER GROUND
Longer pegs are to be used on sandy or
Soft ground earth. A risk assessment of
soil conditions suitability should be
carried out when anchors are to be used.
WORLDWIDE © COPYRIGHT 2016 ITSA GOAL POSTS LTD,
ALL RIGHTS RESERVED A REGISTERED DESIGN
SPARE PARTS
TEL: [phone]