ItsaGoal 16' X 7' ELLIPTICAL FOLDAWAY GOAL Install guide

ELIPTICAL
FOLDAWAY
16' X 7' ELLIPTICAL FOLDAWAY GOAL - FITTING INSTRUCTION
TWIST AND LOCK NET FIXINGS
GROUND FRAME
NET FIXING
A
A
AP
A
B
BARREL
LOCK
BARREL
LOCK
KEY
KEY
Ensure locking
pin is inserted
fully
DO NOT THROW THE
LOCKING PINS AWAY
3
Push locking
pin down
centre
2
Insert ground frame
net fixings into holes
on ground frame
On back frame fix all the same way with opening facing
inwards. On side frames along the ground fit alternate
1
Fit into groove on elliptical posts, Twist 90 degrees to
secure. Position the fixings no more than 340mm apart.
FF
CONNECTOR BALANCE
SNAP ON LOOPS
& WIRE
FOOTBALL GOAL POST
COUNTER BALANCE
WEIGHTS 17Kg STEEL COUNTER
BALANCE WEIGHTS
For use indoors or on
artificial surfaces are
available.
Option 1
Used externally with an
additional connecting
strap
1.
2.
Back ground
frame
Option 2
Used internally. Place
inside the back frame.
MULTI-SURFACE ANCHOR
NET TIE 12
STANDARD GROUND PEG 12
6
COMPONENTS
A
E
B
34
2
4
2
1
QTY
QTY
TWIST AND LOCK NET
FIXING
CORNER BRACKETS
M10 SOCKET DOME SCREW &
HEX DOME NUT - 80mm LONG
BLANKING CAP
GOAL NET
F
I
J
K
L
2
4
BRASS BARREL LOCK
KEY
C
D1
1
LEFT SIDE FRAME
RIGHT SIDE FRAME
BACK GROUND FRAME
70mm Diameter
POST SECTIONS
M
M
CROSSBAR SECTION
115mm x 100mm Diameter 1
1
O
P
WE RESERVE THE RIGHT TO AMEND THE SPECIFICATIONS OF OUR PRODUCTS IN THE INTEREST OF CONTINUED DEVELOPMENT. YOUR PRODUCT THEREFORE MAY DIFFER LIGHTLY TO THOSE ILLUSTRATED. E&OE WORLDWIDE © COPYRIGHT 2013 ITSA GOAL POSTS LTD, ALL RIGHTS RESERVED A REGISTERED DESIGN
Fit tie into bottom horizontal
slot pull tight onto perimeter
net cord not more than 340mm
apart. Wrap tie around posts
and pull through top horizintal
slot to secure. Use in corners
on ground fame and along net
support tubes.
IF USING COUNTER BALANCE WEIGHTS
TOTAL WEIGHT REQUIRED TO CONFORM
TO BS8462:2012 is 107 Kg
6 external weights (pairs) with one single
weight inside the back ground frame
COUNTER BALANCE WEIGHT
OPTIONAL EXTRA
CONFORMS TO BS8462:2012
SPARE PARTS TEL: [phone]
SIDE FRAMES CAN BE FOLDED
INWARDS AND LOCKED IN
POSITION FOR COMPACT STORAGE.
ENSURE THE GOAL IS SAFELY
SECURED WHEN NOT IN USE
IDEALLY LAID ON THE GROUND.
RECOMMENDED
OPTIONAL
REMOVABLE
TRANSPORTER
WHEELS
AVAILABLE
OPTIONAL
REMOVABLE
LIFTING
HANDLES
FOR USE WITH
WHEELS
REMOVE BACK GROUND FRAME
FOLD INWARDS
AND LOCK.
Lugs
If lugs prevent the rod being
inserted fully, nip the plastic
lugs off so the fixing sits flush
Insert rod
slightly lower
than level
Push the rod slightly inside.
Make sure the rod does not go fully
through and fall out or the fixing
will not lock

10mm
30
GROUND FRAME NET
FIXING
L
WARNING
ALL GOALS MUST BE SECURELY ANCHORED
AND OR CORRECTLY COUNTER BALANCED IN
ACCORDANCE WITH CURRENT GOALPOST
SAFETY STANDARDS AT ALL TIMES. CONTACT
THE FOOTBALL ASSOCIATION FOR THE
LATEST SAFETY INFORMATION & READ OUR
CARE AND MAINTENANCE DETAILS.
THE GOAL MUST BE HANDLED CAREFULLY - DO NOT
DRAG GOALS. DO NOT USE GOAL FRAMES WITHOUT
LOCKS. GOALS MUST ALWAYS BE FULLY DISMANTLED
AFTER USE. THE STANCHIONS ARE FOR SUPPORTING
NET ONLY; DO NOT LIFT GOAL WITH THE STANCHIONS.
LONGER PEGS ARE AVAILABLE FOR USE ON SANDY
GROUND. ON GRASS, A RISK ASSESSMENT OF SOIL
CONDITIONS SUITABILITY SHOULD BE CARRIED OUT
WHEN ANCHORS ARE TO BE USED. ANY DAMAGE
CAUSED BY MIS-USE IS NOT COVERED UNDER THE
GUARANTEE
R
Registered Design 5000197 5000198 5000199
European & USA Patent GB 2423260

Folding Goal posts – Elliptical
Football Goalposts must at all times be used in accordance with the fitting instructions provided. When
freestanding moveable goalposts are being positioned prior to a game children should not be allowed to use the
goalposts until they are secure and anchored safely. Never position the goalpost and then go for the second
goal before first making sure the first goal is securely anchored down.
Goalpost should be checked regularly and must be stored away safely as per instructions when not in use. This
care and Maintenance information follows our own risk assessments and those of the Football Association
Guidance Notes of ‘best practice’ to help ensure goals are safe. Sufficient counter balance weights or anchors
must be attached to the goal at all times if it is left in its play position. When stored against a wall the goal
frames MUST be secured on suitable brackets. If brackets are not available they should be stored flat face
down on the ground. They should never at any time be lent against a wall unsecured. All Heavier free standing
goal frames above 45 kilos in weight require additional care and attention when used around children.
The elliptical Foldaway goal was designed specifically with transportation and storage in mind. The goal is
designed to be used on a grass with multi-surface anchors or on artificial grass with counter balance weights.
Permanent anchor points can also be used to secure the goal in a fixed and permanent match position.
Note:- LARGER GOALPOSTS MUST BE MOVED WITH REAR GROUND FRAME ATTACHED
Goal post assembly
To avoid damage when assembling the goal follow these guidelines:
1. A competent adult should assemble the FOLDING GOAL and follow the fitting instructions provided.
Individuals taking over future use of the goal posts should be instructed on the safe usage of the goal posts,
how they are used in play, whilst being moved around and when in storage. Copies of goalpost fitting
instructions can be attained on the website (www.itsagoal.net) for any new users of the goal posts.
2. Always observe and Follow the warning labels attached to the goal. During the life of any goalposts warning
labels may become worn and these should be replaced. Goalpost spares including warning labels are readily
available from ITSA Goal.
3. Always fold out the side frames on a flat section of ground and return back to a flat area when folding sides
under crossbar after use. (Ideally a boarded area by your container or store )
4. Assemble the goals on a flat surface, if it is not flat the bolt holes my not line up correctly.
Goal post frame
If the folding goals are to moved frequently any distance we recommend using wheels or dollies and adding the
optional a back bar. Never allow one person to drag the goals along the ground as this will damage the corners
and may twist the connectors and jam the locks in place making them difficult to remove after use. Prolonged
misuse like this will permanently damage the goal frame.(see Fig 2)
1. NEVER use net stanchion supports to lift or drag the goal. This may cause the stanchions to bend and
deform. Net supports are designed to support goal nets not people swinging on them.
2. Ensure you have an adequate number of physically fit and capable adults available when moving goalposts.
Never allow children to move goalposts or play with the goalposts whilst they are being positioned for a game.
3. It is advisable not to drag the goal across the ground as this may damage the goal and playing surface. Lift
the goal and carry with upright in one hand and side ground frame in the other (two people) or lift from the rear
and pull when wheels are attached at the front (one person can then move the goal frame)
4. Do not place fingers at the top of the upright ( inside the void created by the upright being oval in shape)
when side frames are rotating.
5. ALWAYS lock the side frames in position when in play.
6 We would recommend Pneumatic wheels to move you goal on wet muddy surfaces and smaller hard wheels
be used on artificial grass.
Goal with sides folded out for Use
Goal posts must NEVER be left up if unsupervised. Side frames must be locked during use to prevent the sides
from swinging about which will make the goalpost unstable.
The folding Goal frame must be anchored immediately the side frames have been locked in the play position.
NEVER walk away from the assembled goal frame until it is securely anchored.
NEVER allow anyone under any circumstance to climb or swing on the crossbar prior to the goal being
anchored. Discourage this activity of swinging on crossbars at all times at your football club. It is a very
common practice with young children but highly dangerous (see goalpost safety section on our web site)
DO NOT use any components, nets or parts if they are damaged or broken. Goal post Repairs & spare parts
are readily available from our web site. Do not tamper with Goalposts.
The folding goalpost is not designed to be dragged as this can weaken and damage the corners of the goal
frame. Always move the goalposts with sides folded out in the play position as shown on the fitting instructions.
The folding goal can be moved easily by one person with wheels. (See moving the goalposts on
www.soccertackle.com web site) We recommend Goals transporter dollies for moving larger folding goalposts.
Goal with sides folded under crossbar for storage
Do not move goalposts with sides locked underneath the crossbar, for play fold out into the play position
before moving if at all possible. The goalpost can however be moved in the none play position (side frames
under crossbar) in certain tight access locations however it is important that individuals walk on the side the
wind is blowing to prevent the frame blowing over onto them if a sudden gust happens ; however, it is not
adviseable to move the goals in extreme windy conditions.
When removing the goal post from the playing surface ensure that all fittings are packed away and that non
are left on the pitch.
NEVER leave the goal post frame with sides folded under the crossbar and lent against a building or wall
without first securing the goal post from toppling forward.
When folding the side frames back under the crossbar do it on a flat area.
Locks & Keys Do not force the key. A gentle movement of the side frame outwards past the ninety degree
position) as you turn the key helps push the lock out after use. We suggest that furniture polish be applied to
the lock housing and the corners to make movement of the parts easier.
If the key breaks in the lock and you do not have enough of the key exposed to pull it out then we advise to
turn the upright around and tap the outside of the post with a rubber mallet and gravity should see the key
drop out or sufficiently down from the lock to pull out with pliers.
Replacement and spare keys are readily available.
As these are the only locking secure side frames on any folding goal it is important to tell everyone using the
folding goals that they are locked and do not just push in and out like other less stable folding goalposts. We
have had volunteers actually push the side frames with the locks secured until they broke them as they had
never seen locking frames only loose ones that swung about. Explain to all users how the goals work and the
safety benefits they offer.
Moving the heavier elliptical goal
In order to move the Elliptical Foldaway goal ideally wheel attachments should be attached. If moved manually
it should be lifted and carried fully assembled Carried with rear ground frame attached with left hand on
upright and right hand on side frame (and vice-verse at the other side of the goalpost) as set out above. Goals
must be fully assembled ideally when moving the goals.
please take note that additional measures need to be taken into account when moving this goal.
1. When moving the goal ensure that you NEVER have anyone walking directly behind in the path of the
goalpost frame or underneath the frame.
2. Freestanding goalposts should NEVER be moved without an adequate number of physically fit and capable
people who have been fully trained to use proper lifting techniques. A full size goal should never be manually
moved using fewer than four adults or two adults with wheels or dollies.
3. Goalpost Wheels should be of a type suitable for the surface in which it will aid the goal to move across.
Hard wheels are designed for firm or indoor surfaces while pneumatic wheels are for soft ground.
ELLIPTICAL FOLDAWAY CARE MAINTENANCE 2014.CDR
CARRY GOALS
FULLY ASSEMBLED
ALWAYS
WITH BACKBARS ATTACHED
Fig 1. Fig 2. Fig 3.
Fig 4.
Fig 5.
Fig 6.
NEVER SWING ON
CROSSBARS
CONTAINER STORAGE
1Lay goal flat
down on ground.
Insert Wheels on
both uprights
Lift goals upright - two adults
Steer/move goal into position
with lock in place at the rear.
Add ground back bar as
per fitting instructions
RAMP
made of earth,
gravel, or concrete
CHECK HEIGHT
of your container -
see the height (B)
of the goal on the
transporter
photograph
(btm left)
If goals are stored in containers it is recommended
to build a small ramp up to the container
entrance. This will improve handling
of the goals and speed up the
time taken setting up goals.
Insert sufficient anchors,
counter weights or
chain to fixing points
456
23
WORLDWIDE © COPYRIGHT 2001 ITSA GOAL POSTS LTD, ALL RIGHTS RESERVED A REGISTERED DESIGN
R
Registered Design 5000197 5000198 5000199

Recessed Net Fixings
Fit the recessed goal net fixings into the rear slots on the goal post sections and twist 90 degrees to secure.
Position the fixings not more than 400mm apart. The Recessed net fixings are Designed to fit ITSA goal rear
slotted aluminum goal posts. When goal nets are left attached they can also be secured with a 4mm rod that
can slide down through the net fixings to prevent unauthorized removal of the net fixings or goal net
Multi-surface anchors
Multi-surface anchors are designed to secure the
freestanding goalposts to normal grass surface pitches
( to1100Newtons forward pull test). On a grass surface
use the ground pegs provided in conjunction with the
multi-surface anchors. If ground is softer then more
ground anchors can be used to spread the load or longer
pegs can be inserted. The safety ground pegs can also
be used to retain your net if rear ground frames are not
used with the folding goal. Always angle the pegs as shown
on the fitting instructions to give maximum affect.
To remove stubborn pegs use another peg to lift out do
not pull out with the anchor itself or it may damage the
securing cross holding the peg in place. This is strong
system designed to twist under stress and will not easily
be damaged.
If you are planning to anchor your goal post on tarmac the fixing positions for the multi- surface anchors need to
be secure. We advise :-
1. Dig holes in your tarmac (to sizes specified in fitting instructions ).
2. Fill holes with concrete, and drill two 14mm holes 12cm apart and 70mm depth.
3. Position goal and multi-surface anchors and use a suiable10mm concrete bolt instead of the safety grass
pegs.
For other surfaces such as wooden sports hall floors wood screws in our multi-surface anchor or counter
balance weights can be used. The total weight to conform to the current standards for the goal post topple test
can be worked out from the equation worked out in conjunction with Sheffield University.
Goalpost Nets
All our square mesh nets are made to the shape of
the net. If you are putting nets up each week we
recommend that you locate the top corners first and
mark them using tape so that you can easily identify
them each time. Folding goal posts however are
designed to enable the net to be left on the goal
frame in the non- play position to allow swift match
day installation. Place the net over the frame and fit
each end onto top stanchion by securing on each
corner of the crossbar and uprights using twist and
lock net fixings.
Folding goalpost net fixing instructions
we recommend only nets with 100mm x 100mm mesh be used With children, to cover head entrapment
regulations, Nets with 120mm x 120mm mesh are acceptable for use by adults.
Nets can be tied into a bundle and placed into a pillow case (not to damage washing machine) and washed at
40 degrees Celsius with normal washing powder to keep them in tip top condition.
Be aware rabbits and rodents have been know to nibble at the base of nets. If nets are left outside we advise
lifting off from ground level. If you have this problem sprinkle pepper along the bottom of the net and this
should help deter most wild animals.
Counter balance weight system
The ITSA GOAL posts counter balance weight system consists of two counter balance weights each weighing
11kgs fastened together to offer 22 kilos of counterweight spread over 500mm.
The counter balance weight system is used on flat level playing surfaces or where multi- surface anchors can
not be used. ie. Sports halls, artificial grass pitches, etc. The two connected weights together can be lifted on
the frame and used externally.
If anchoring your freestanding goalpost is not possible, the guidance and technical notes set out by The
Football Association give clear instructions for the use of counter balance weights. If you are unsure what
weight you are required to use on your freestanding goal posts, you can work out the weight needed by using
the following procedure.
1 Measure the height of the crossbar.
2 Measure the length of the goal’s side bars.
3 Divide the height by the length. Multiply the result by 112Kg and make a note of the answer.
This is the total weight in kilograms that should stabilizes the goal to safety standards.
Example: A Regulation Goal, 2.44m high with a 2.025m ground side frame the calculation would be: 2.44
divided by 2.025= 1.205 therefore 1.205 x 112Kg = the total weight required for this goal would be 135Kg (less
the weight of the back ground bar).
Test each goal post before use to satisfy yourself that you have enough counter balance weights
attached to the goal to prevent topping.
Chain and cable attachments
Whatever method is used to stabilize a goal, any attachment chain or a wire cable between the goal and the
weight, anchor, eye bolt or other fixing point should be as short as possible and not allow the back bar to lift
more than 50 mm.
Care and Maintenance
1. NEVER use our goalposts without securing locks or
correct fittings or in non conforming ground sockets.
2. DAMAGED COMPONENTS requested under
guarantee must be returned for inspection.
Failure to follow the warnings, assembly and fitting
instructions contained in this document,
may invalidate your guarantee.
IT IS ADVISABLE IN ANY CONTACT SPORT TO
TAKE OUT THE RELEVANT INSURANCE’S TO
COVER ALL UNFORESEEABLE CIRCUMSTANCES.
IT IS ADVISEABLE TO CHECK YOUR GOALS WEEKLY AND UNDERTAKE ANY MAINTENANCE, CHECK
PAINTWORK, CHECK NETTING, MAKES SURE ANY LOCKS OR BOLTS ARE IN PLACE , ENSURE THE
FRAME IS ASSEMBLED IN ACCORDANCE WITH THE FITTING INSTRUCTIONS BEFORE EACH GAME.
ANY NEW PEOPLE USING THE GOALS SHOULD BE PROVIDED WITH THIS LEAFLET AND THE
FITTING INSTRUCTIONS AVAILABLE FROM www.itsagoal.net .
MULTI-SURFACE
ANCHOR
SAFETY
GROUND
PEG
ANCHOR POSITION LABEL
250mm in from end of
upright and base of
stanchion support.
GROUND FRAME
WASHER
DRILL HOLE
2 x MULTI SURFACE
ANCHORS
M10 SLEEVE ANCHOR
RAWBOLT
CONCRETE BLOCK
(FOR USE ON TARMAC)
12cm(min)
30cm
12.3cm
18cm
CONCRETE BLOCK
(FOR USE ON TARMAC)
12cm(min)
30cm
12.3cm
18cm
THIS METHOD SECURELY
ANCHORS YOUR GOAL DOWN
ON TARMAC. DO NOT OVER TIGHTEN BOLT.
REMOVABLE COUNTER BALANCE OPTION
LOCKING COUNTER BALANCE OPTION
We offer locking counter balance using the‘gripple system’.
This is ideal in public areas to prevent unauthorised
removal of counter weights.
Contact our office for further information
TEL [phone]
ELLIPTICAL FOLDAWAY CARE MAINTENANCE 2014.CDR
For video demonstrations visit :
www.youtube.com/Footballgoalposts
NEVER leave the goals
unattended with the wheel
transporters still attached
as shown to the left .
Always move the goals into
the position required and
then anchor the goals to
the playing surface using
ground anchors or weights
as recommended on the
fitting instructions supplied
with your goalposts. Never
move the goals in extreme
weather and gales.
DO NOT remove anchors
using goal frame, use the
back of the ground peg.
NEVER stand or apply any weight
on the side frame marked ‘A’ as
this can damage your equipment.
WARNING STEERING GOALPOSTS
A
B
Total height B from ground level
Full size goals - 271cm , Youth goals - 240cm
Mini soccer goals -210cm
CROSSBAR
SIDE
FRAME
WORLDWIDE © COPYRIGHT 2001 ITSA GOAL POSTS LTD, ALL RIGHTS RESERVED A REGISTERED DESIGN
WORLDWIDE © COPYRIGHT 2001 ITSA GOAL POSTS LTD, ALL RIGHTS RESERVED A REGISTERED DESIGN
Insert lock here
when moving goals
R
Registered Design 5000197 5000198 5000199

GOAL POST TRANSPORTER
Freestanding Elliptical Aluminium Goalposts
800mm Width
How to use the Goal Post Transporters
Ideal for larger Adult & Youth size goals
Ideal for smaller mini soccer goals.
300mm Width
For video demonstrations visit : www.youtube.com/Footballgoalposts
The only steerable system - Exclusive to ITSA Goal
To add the wheel transporters to the base of your goals it is recommended to carefully, with
at least two adults lay the goals flat on the floor. Hold the ground side frame vertical and
slide the wheel transporter inside the bottom of the upright. Once both wheel transporters
are connected carefully lift the goals up so the uprights are vertical. It is important to be very
careful that the crossbar does not come away from the side frames when the goals are
being moved. Always assemble on flat level ground. Make sure children are not in the
vicinity when moving and anchoring goalposts.
The side frames can rotate whilst the crossbar is not locked. This allows the goals to be
moved in all directions, ideal when you have to store goals in awkward storage areas.
However extra care must be taken whilst the crossbar is not locked to the side frames to
prevent the crossbar coming apart from the side frames and falling. We recommend When
the goal posts are in position for play the barrel locks must be inserted to lock the goals as
shown on the goalpost fitting instructions. Likewise when the goals are in storage the goals
should have the locks in place for extra stability and to prevent the side frames swinging
inward. It is also advised when the goals are in storage to make sure the goals are stored to
prevent toppling and secured against a wall and not left freestanding. Always take great care
with heavy freestanding football goals.
Set includes
Two aluminium weather proof ‘T’ frames, Four Puncture proof Pneumatic Wheels
Set of two are required to move one goal. The wheels can be used on any number of
115mmx100mm elliptical aluminium goal posts
NEVER leave the goals
unattended with the wheel
transporters still attached as
shown to the left . Always
move the goals into the
position required and then
anchor the goals to the
playing surface using ground
anchors or weights as
recommended on the fitting
instructions supplied with
your goalposts. Never move
the goals in extreme
weather and gales.
DO NOT remove anchors
using goal frame, use the
back of the ground peg.
NEVER stand or apply any weight
on the side frame marked ‘A’ as
this can damage your equipment.
WARNING STEERING GOALPOSTS
CONTAINER STORAGE
A
B
Total height B from ground level
Full size goals - 271cm , Youth goals - 240cm
Mini soccer goals -210cm
CROSSBAR
SIDE
FRAME
WE RESERVE THE RIGHTS TO AMEND THE SPECIFICATIONS OF OUR SOCCER PRODUCTS IN THE INTEREST OF CONTINUED DEVELOPMENT. YOUR PRODUCT THEREFORE MAY DIFFER LIGHTLY TO THOSE ILLUSTRATED. E&OE
WORLDWIDE © COPYRIGHT 2001 ITSA GOAL POSTS LTD, ALL RIGHTS RESERVED A REGISTERED DESIGN
1Lay goal flat
down on ground.
Insert Wheels on both uprights
Lift goals upright - two adults
Steer/move goal into position with lock in place at the rear.
Insert lock here
when moving goals
Add ground back bar as per fitting instructions
RAMP made of earth, gravel, or concrete
CHECK HEIGHT
of your container - see the height (B) of the goal on the transporter photograph (btm left)
If goals are stored in containers it is recommended to build a small ramp up to the container entrance. This will improve handling of the goals and speed up the time taken setting up goals.
Insert sufficient anchors,
counter weights or
chain to fixing points
456
23
R
Registered Design 5000197 5000198 5000199