ItsaGoal 16' X 7' MULTI-SURFACE YOUTH GOAL User manual

E
E
O
O
A
A1
B
I
X
P
N
NI
K
PLEASE NOTE :
THE NET TIES
CAN BE USED TO
TIE THE NETS TIGHTLY
INTO THE CORNERS
FOR A BETTER FIT.
GInsert ground frame net
fixings in the sidebar
sections and backbar
sections.
DO NOT THROW
THE LOCKING
PINS AWAY
IF GOALS HAVE INTENSIVE USE ADD
THE ADDITIONAL NET TIES TO THE
GROUND BASE FRAME
NF ALTERNATE
FACE FORWARD
P
O
CARE & MAINTENANCE
- see separate sheet supplied or visit
www.itsagoal.net for additional copies.
Our goalpost if used correctly will last
many years. We do also offer a full spare
part service and if your goals need
refurbishment this can be arranged
J
OPTIONAL TIES
GOAL POSTS MUST BE ANCHORED AT ALL TIMES
Optional longer pegs are available for use on sandy
ground. On grass, a risk assessment of soil and
weather conditions suitability should be carried out when
anchors or counter weights are to be used.
Extra anchors are available TEL: [phone]
TEL: [phone]
SPARE PARTS
16' X 7' MULTI-SURFACE YOUTH GOAL
ALUMINIUM
CROSSBAR
(16' x 7') Two section Aluminium crossbar.
To register for your guarantee visit www.itsagoal.net
scroll to the bottom of the page and click on the link ‘Guarantee’
and follow the instructions. Thank you.
REGISTER YOUR GUARANTEE
Guarantee
68mm
68mm
68mm
40mm
40mm
2
2
2
2
2
x
x
x
x
x
BACKBAR SECTION
2422mm LONG - 68mm Diameter
SIDEBAR SECTION
UPRIGHT SECTION
TOP STANCHION TUBE
BACK STANCHION TUBE
O
P
Q
R
S
70mm
70mm
1
1
x
x
CROSSBAR SECTION
Without insert - Aluminium
CROSSBAR SECTION
With insert - Aluminium
N
NI
Aluminium Crossbar Only
POST SECTIONS
COMPONENTS
M10 NUT AND BOLT
K4
x
10mm
4
x
4
4
2
4
2
8
10
x
x
x
x
x
x
x
CORNER BRACKET
4 HOLES
SPIGOT
BLANKING CAP
MULTI-SURFACE ANCHOR
GROUND PEG
STANCHION ELBOW
SMALL QUICK RELEASE BUTTON
LARGE QUICK RELEASE
A
B
C
D
E
F
H
I
8
x
NET TIE
J12
x
LOWER BACK STANCHION
G2
x
16
14
x
x
BLACK NYLON ARROW HEAD
NET FIXING with LOCKING PIN
WHITE PLASTIC ARROW HEAD
NET FIXING with LOCKING PIN
MB
MW
1
x
STRAIGHT CONNECTOR
L
1
x
GOAL NET 16' x 7'
NET
ALLEN KEY 1
x
AK
NF GROUND FRAME NET FIXING HOOK 28
x
2
x
CORNER BRACKET
UPRIGHT 8 HOLES
X
WE RESERVE THE RIGHTS TO AMEND THE SPECIFICATIONS OF OUR SOCCER PRODUCTS IN THE INTEREST
OF CONTINUED DEVELOPMENT. YOUR PRODUCT THEREFORE MAY DIFFER LIGHTLY TO THOSE ILLUSTRATED. E&OE
WORLDWIDE © COPYRIGHT 2001 ITSA GOAL POSTS LTD, ALL RIGHTS RESERVED A REGISTERED DESIGN
S
MW
Q
F
R
H
C
PLEASE NOTE :
THE NET TIES
CAN BE USED TO
TIE THE NETS TIGHTLY
INTO THE CORNERS
FOR A BETTER FIT. I
G
O
F
B
I
R
Q
A
I
H
BOLTING CROSSBAR TO
CORNER BRACKET
& STANCHION
FITTING
NOTE: Ensure Top
Stanchion holes
are aligned with the
Stanchion Elbow.
Note : Make sure part C, blanking Cap
is inserted in the corner bracket X with
the 8 holes. This part may already be
inserted.
X
C
H
DO NOT THROW THE
LOCKING PINS AWAY
MB
Insert net hooks in holes on
crossbar/uprights and insert pins to lock
Locking Pin
Arrowhead net fixing
DO NOT THROW
THE LOCKING
PINS AWAY
Insert ground frame net
fixings in the sidebar
sections and backbar
sections.
!

STEP BY STEP ASSEMBLY
WORLDWIDE © COPYRIGHT 2016 ITSA GOAL POSTS LTD, ALL RIGHTS RESERVED A REGISTERED DESIGN
STEP 2
Insert Blanking Cap part C and
insert Large Quick Release Button H (x2)
into Corner Bracket X.(NOTE: CornerBracket X
is different from Corner Bracket A. Corner
Bracket X is to be fitted into the upright posts
and has 8 holes.
STEP 3
Insert Small Quick Release Black Button I
into the Spigot B. Insert Spigot B and
insert H (x2) into Corner Bracket A.
(NOTE: Corner Bracket A has 4 holes)
STEP 4
Insert Arrow Head Net Fixings MW
into Upright Posts and insert black
MB fixings into crossbar.DO NOT
THROW AWAY LOCKING PINS
STEP 5
Insert Ground Frame net Fixings NF
into Back bar and Side bar. see details
about removing burrs overleaf.
DO NOT THROW AWAY LOCKING PINS
X
C
H
C O R N E R
BRACKET
H
A
C O R N E R
BRACKET
SPIGOT B
I
FOR EASIER ASSEMBLY Use a rubber mallet and also spray furniture polish inside posts. Do not use a metal hammer. Do not apply grease or vaseline.
STEP 6
Insert Corner Brackets X into the
upright posts Q (uprights have logos on the side)
STEP 7
Insert Corner Brackets A into
each end of the crossbar N
STEP 8
Insert Corner Brackets A into
each end of the Backbar O
STEP 9
Attach Side bars P to the ground
back,connect both back bars
together with the straight
connector L
STEP 10
Attach Upright Q to
the Side bars P
STEP 11
Fit the crossbar together
NI (crossbar with insert) with
K nuts and bolts to Crossbar L . Then fit crossbar.
L
XAA
G
ANCHORING YOUR GOAL ON GRASS - POSITION YOUR GOAL ON A LEVEL PLAYING SURFACE.
PLACE THE MULTI-SURFACE ANCHOR OVER EACH SIDE OF THE GROUND FRAME (POSITIONS
SHOWN) HAMMER THE PEGS DOWN UNDER THE FRAME INTO THE GRASS. ADDITIONAL
ANCHORS OR LARGER PEGS CAN BE PURCHASED FOR USE ON SOFT GROUND OR SAND. THESE
ANCHORS CAN BE USED FOR HARD SURFACES, SUCH AS TARMAC BY USING BOLTS THROUGH
THE MULTI SURFACE ANCHORS INTO CONCRETE PADS. COUNTER BALANCE WEIGHTS CAN ALSO
BE USED (SUPPLIED SEPARATELY). CHAINS ARE AVAILABLE SEPARATELY THAT CAN BE USED TO
SECURE GOALS TO SEPARATE ANCHOR POINTS.
PEG
REMOVAL
a
b
a
b
G
OPTIONAL TIES
WORLDWIDE © COPYRIGHT 2001 ITSA GOAL POSTS LTS, ALL RIGHTS RESERVED A REGISTERED DESIGN
STEP 1
Lay out all Posts & components
UPRIGHT
SECTION
R
S
Q
P
SIDEBAR
SECTION TOP
STANCHION
TUBE
BACK STANCHION TUBE
CROSSBAR
SECTION
With insert
NI
CROSSBAR SECTION
Without insert
NBACKBAR SECTIONS
O
STEP 12
Join top tubes
R to elbows F
and back
tubes S and
connect to the goalpost.
STEP 13
Attach two of the Ground
Anchors. see details over.
ASSEMBLY & DISASSEMBLY
FASTER
MATCH DAY
STEP 14
Fit the net - attach the net to each corner first where the crossbar meets the uprights.
On the back ground bar at the back of the goal extra netting can be rolled and tied
to the back ground bar for a neat finish. Finally add the two
remaining anchors on the ground back bar with the
netting underneath as shown. The goal net can be left
attached to the
pre-assembled
goal post
side frames. After
games detach crossbar
and back bar for storage.
We advise fitting the optional net ties
to the side frames and stanchions.
NET
CORD
R
F
S
OPTIONAL - Net ties are ideal to fit nets tightly to the
side ground frames and stanchions. This is ideally
when nets are left attached to the fully assembled side
To define the roof of the net Tie
the cord to one side and pull the
net cord tight and wrap neatly
down and around the stanchion
tube If you are regularly
attaching or detaching the net
then apply coloured tape to the
roof corners to help identify.
!

We advise adult supervision during assembly and use. Observe and follow
warning labels attached to goal. Do not use any components, nets or parts
if they are damaged or broken. Spare parts and replacement nets are
readily available. If others are to install your goal you should show them
how to erect and dismantle the goal and hand them a copy of the fitting
instruction. If you lose your instructions copies can be attained from our
company website. To avoid damage when dismantling the goal follow
these guidelines: it is advisable in extreme windy conditions to dismantle
the goal and store away. Do not drop any heavy objects on ends of tubes.
When dismantling the goal ensure that all fittings are packed away and
that non are left on the playing surface. Warning goals must never be left
up or used unless they are properly fitted with ground anchors with net
attached and securely pegged down.
Hard surfaces: to prevent damage to goal or it's components, loosen soil
with a steel pole and moisten with some water before inserting the ground
anchors. Do not use the goal in sub zero temperatures. warning labels
should be replaced when worn and we recommend replacing them every
two years -spare labels available. damaged components requested under
guarantee must be returned for inspection. Failure to follow the warnings,
fitting instructions contained in this document, may invalidate your
guarantee. The company , its agents and representatives do not accept any
product liability if used outside the EU. Use of the product in other
countries outside the EU including the USA is not covered and appropriate
insurance should be taken out by the user to cover for any eventuality. We
reserve the rights to amend the specifications of our soccer products in
the interest of continued development. Your product therefore may differ
slightly to those illustrated. Not suitable for children under 36 months until
assembled due to small parts.
TEL: [phone]
SPARE PARTS
NET TIES
!
1
TEETH
3
2
NET CORD
4
6
7
8
Ensure the teeth of the
Net tie are facing you
(see step 1).
Loop the Net Tie around
the Net Cord and slide
the end into the
horizontal slot and pull
tight onto Net Cord (see
step 1- 2).
The vertical slot of the
Net Tie is used to
secure the net to the
post. Loop the Net Tie
around the post and
insert through
vertical slot and twist to
lock. (steps 3 - 5).
Any excess Net Tie can
looped back into the
vertical slot. This will
also secure the net tie in
a fixed position (steps 6
- 8). If Net Ties are to be
removed after use then
do not loop back into
vertical slot.
5
POST SECTION
PULL
TIGHT
WORLDWIDE © COPYRIGHT 2001 ITSA GOAL, ALL RIGHTS RESERVED A REGISTERED DESIGN
WE RESERVE THE RIGHTS TO AMEND THE SPECIFICATIONS OF OUR SOCCER PRODUCTS IN THE INTEREST OF CONTINUED DEVELOPMENT. YOUR PRODUCT THEREFORE MAY DIFFER LIGHTLY TO THOSE ILLUSTRATED. E&OE
Ensure locking pin
Is inserted Fully in
the posts
DO NOT THROW THE PINS AWAY
3
Push locking pin
Down centre of
Arrow Head
2
Insert Arrow Head
into Holes on
posts
1
GROUND FRAME
NET FIXING
Ensure locking
pin is inserted
fully
DO NOT THROW THE
LOCKING PINS AWAY
3
Push locking
pin down
centre
2
Insert ground frame
net fixings into holes
on ground frame
On back frame fix all the same way with opening facing
inwards. On side frames along the ground fit alternate
1
Lugs
If lugs prevent the rod being
inserted fully, nip the plastic
lugs off so the fixing sits flush
Insert rod
slightly lower
than level
Push the rod slightly inside.
Make sure the rod does not go fully
through and fall out or the fixing
will not lock


NOTE : All plastic extrusions vary and therefore some tubes may be looser
or tighter to connector fittings. If you want to increase the diameter of the
fitting just wrap masking tape around the part that fits into the tube, twist
as you insert the fitting and it will grab to the tube tight ...you can make
tighter fits by adding more tape.
To register for your guarantee visit www.itsagoal.net
scroll to the bottom of the page and click on the link ‘Guarantee’
and follow the instructions. Thank you.
REGISTER YOUR GUARANTEE
Guarantee
ANCHORING YOUR GOAL
NET FITTING
WARNING: Check the position of any underground services before using the ground anchors and pegs.
We take no responsibility for any damage or injury caused in this manner.
HARD SURFACES: to prevent damage to goal or it's components, loosen soil with a steel pole and
moisten with some water before inserting the ground anchors. Do not use the goal in sub zero
temperatures.
ANCHORING YOUR GOAL ON GRASS - POSITION YOUR GOAL ON A LEVEL PLAYING SURFACE.
PLACE THE MULTI-SURFACE ANCHOR OVER EACH SIDE OF THE GROUND FRAME (POSITIONS
SHOWN) HAMMER THE PEGS THROUGH THE HOLES (DO NOT USE METAL HAMMERS USE RUBBER
MALLETS) ON THE ANCHOR DOWN UNDER THE FRAME INTO THE GRASS ADDITIONAL ANCHORS
OR LARGER PEGS CAN BE PURCHASED FOR USE ON SOFT GROUND OR SAND. THESE ANCHORS
CAN BE USED FOR HARD SURFACES SUCH AS TARMAC WITH OPTIONAL BOLTS. ON HOT/SUNNY
DAYS TARMACADAM SOFTENS AND THEREFORE TO ANCHOR YOUR GOAL PROPERLY YOU MUST:-
1 DIG HOLES IN YOUR TARMAC FILL HOLES WITH CONCRETE , 2 DRILL TWO 14MM HOLES 12CM
APART AND 70MM DEPTH. 3 POSITION GOAL AND ANCHOR, INSERT AND TIGHTEN BOLT.
FOR OTHER SURFACES SUCH AS WOODEN SPORTS HALL FLOORS WOOD SCREWS (INSTEAD OF
BOLTS) OR COUNTER BALANCE WEIGHTS CAN ALSO BE USED (SUPPLIED SEPARATELY).
INSERT MULTI-SURFACE
ANCHOR PEGS FULLY
GROUND
FRAME
WASHER
DRILL HOLES
2 x MULTI SURFACE
ANCHORS
M10 SLEEVE
ANCHOR
RAWBOLT
12cm(min)
30cm
12.3cm
18cm
12cm
(minimum)
30cm
12.3cm
18cm
THIS METHOD SECURELY ANCHORS
YOUR GOAL DOWN ON TARMAC
DO NOT OVER TIGHTEN BOLT.
CONCRETE BLOCK
(FOR USE ON
TARMAC)
GROUND
FRAME
WASHER
DRILL HOLES
2 x MULTI SURFACE
ANCHORS
M10 SLEEVE
ANCHOR
RAWBOLT
12cm(min)
30cm
12.3cm
18cm
12cm
(minimum)
30cm
12.3cm
18cm
THIS METHOD SECURELY ANCHORS
YOUR GOAL DOWN ON TARMAC
DO NOT OVER TIGHTEN BOLT.
CONCRETE BLOCK
(FOR USE ON
TARMAC)
SQUARE MESH Net is cut to shape. Simply
throw over the frame and fit each end onto top
stanchion by securing on each corner of
crossbar. NOTE: If your net does not fit the first
time, you may be fitting it to the goal frame
upside down i.e. that is to say the net from the
crossbar to the floor (a) is longer than the
length of the net to the bottom of the upright.(b)
CHECK THE NET
Open net and check the lengths of a
and bcorrespond with the diagram below.
a
b
a
b
At the end of the season nets can be tied into a bundle and placed into a pillow case (not to damage washing
machine) and washed at 40 C0 with normal washing powder. The ground frame can be washed with hot
soapy water. Any scuff marks on posts can be rubbed off with a light abrasive scouring pad.
WARNING: Check the position of any underground services before using the ground anchors and pegs. We
take no responsibility for any damage or injury caused in this manner.
NEVER use the goals without the ground anchor system. In severe weather or windy conditions it is advisable
to take your goal down as damage is not covered by the guarantee in such circumstances. If you find the nets
are worn along the floor it may be rodents, by spreading pepper along the base frame rodents will be
deterred.
It is advisable in any contact sport to take out the relevant insurance's to cover against injury both from taking
part, equipment and other unforeseeable circumstances.
Crossbars will not be replaced within the guarantee period if broken by swinging or climbing or any other
misuse.
DO NOT try to glue any damaged fixings. Plastic materials in this product vary and this may cause the plastic
to break. Always replace any damaged components. !