Jøtul GF 400 BV Sebago User manual

1
138301_Rev_G 10.4.11
Installation and
Operation Instructions
Jøtul GF 400 BV Sebago
Natural Vent Gas Stove
– Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
– WHAT TO DO IF YOU SMELL GAS
 •Donottrytolightanyappliance.
 •Donottouchanyelectricalswitch;donot
use any phone in your building.
 •Immediatelycallyourgassupplierfroma
neighbor’sphone.Followthegassupplier’s
instructions.
 •Ifyoucannotreachyourgassupplier,call
the fire department.
– Installation and service must be performed
byaqualifiedinstaller,serviceagencyorthe
gas supplier.
– IntheCommonwealthofMassachusetts,
a carbon monoxide (CO) detector shall be
installed in the same room as the appliance.
WARNING: If the information in these
instructionsisnotfollowedexactly,afire
or explosion may result causing property
damage,personalinjuryorlossoflife.
INSTALLER:Leavethismanualwiththeappliance.
CONSUMER: Retain this manual for future reference.
– QUEFAIRESIVOUSSENTEZUNEODEURDEGAZ:
 •Nepastenterd’allumerl’appareil.
 •Netouchezàaucuminterrupteur.Ne
pas vous servir des téléphones se trouvant
danslebâtimentoùvoustrouvez.
 •Appelezimmédiatementvotre
fournisseurdegazdepuisunvoisin.
Suivezlesinstructionsdufournisseur.
 •Sivounepouvezrejoindrele
fournisseurdegaz,appelezleservicedes
incendies.
– L’installatione l’entretien doivent être
assurés par un installateur ou un service
d’entretien qualifié ou par le fournisseur
degaz.
– Ne pas entreposer ni utiliser d’essence ni
d’autres vapeurs ou liquides inflammables
dans le voisinage de cet appareil ou de tout
autre appareil.
AVERTISSEMENT:Assurez-vousdebien
suivreles instructions données dans cette
notice pour réduire auninimum le risque
d’incendie ou d’explosion ou pour éviter
toutdommagematériel,touteblessureoula
mort.
ATTENTION : CES INSTRUCTIONS DOIVENT
DEMUERER AVEC LE PROPRIÉTERE D’UNE
MAISON.
Thisappliancemaybeinstalledinanaftermarket,
permanentlylocated,manufacturedhomeormobile
home,wherenotprohibitedbylocalcodes.
Thisapplianceisonlyforusewiththetypesofgas
indicated on the rating plate. A conversion kit is
suppliedwiththeappliance.

2
138301_Rev_G 10.4.11
We recommend that
our gas products be
installed and serviced by
professionals who are
certified in the U.S. by
the National Fireplace
Institute® (NFI) as NFI Gas
Specialists.
64.20%
Jøtul GF 400 BV
Installation Requirements for the
CommonwealthofMassachusetts
THIS PRODUCT MUST BE INSTALLED BY
A LICENSED MASTER OR JOURNEYMAN
PLUMBER OR GAS-FITTER WHEN
INSTALLED IN THE COMMONWEALTH OF
MASSACHUSETTS.
1. If there is not one already present, on each
floor level where there are bedroom(s),
a carbon monoxide detector and alarm
shall be placed in the living area outside
the bedroom(s). The carbon monoxide
detector shall comply with NFPA 720
(2005 Edition).
2. A carbon monoxide detector shall:
a) Be located in the room that houses the
appliance or equipment;
b) Be either hard-wired or battery
powered or both; and
c) Shall comply with NFPA 720 (2002
Edition).
3. A Product-approved vent terminal must
be used, and if applicable, a Product-
approved air intake must be used.
Installation shall be in strict compliance
with the manufacturer’s instructions. A
copy of the installation instructions must
remain with the appliance or equipment
at the completion of the installation.
THIS OWNER’S MANUAL PROVIDES INFORMATION TO
ENSURESAFEINSTALLATIONANDEFFICIENT,DEPENDABLE
OPERATION OF YOUR FIREPLACE INSERT. PLEASE READ
THESE INSTRUCTIONS IN THEIR ENTIRETY AND MAKE THEM
AVAILABLE TO ANYONE USING OR SERVICING THIS GAS
INSERT.
DO NOT ATTEMPT TO ALTER OR MODIFY THE CONSTRUCTION
OF THIS APPLIANCE OR ITS COMPONENTS. ANY
MODIFICATIONORALTERATIONWILLVOIDTHEWARRANTY,
CERTIFICATION AND LISTING OF THIS APPLIANCE.
THIS HEATER MUST BE INSTALLED AND MAINTAINED BY A
QUALIFIED SERVICE AGENCY.
















Suggested Tools for
Installation and Service
• Externalregulator(forPropaneonly)
• Pipingwhichcomplieswithlocalcode
• Manualshut-offvalve-
 T-HandlerequiredinMassachusetts
• Sedimenttrap-ifrequiredbycode
• Teejoint
• Pipewrench
• Pipesealant
• 10mmopenendwrench
• 1/2”,7/16”openendwrench
• Phillipsheadscrewdriver
• Flatheadscrewdriver
• 1/4”nutdriver
• Gloves
• Safetyglasses
• TorxT-20screwdriver
•Tinsnips

3
138301_Rev_G 10.4.11
Table of Contents
Service Tools .............................................2
Specifications ............................................4
General Information................................5
Safety Information ..................................6
Installation Requirements
Location ................................................6
Hearth Protection ...............................6
Clearances ............................................. 7
Mantel&Trim ...................................... 7
Alcove ....................................................7
Vent Requirements ................................10
Fuel Conversion........................................ 11
Gas Connection........................................13
Gas Pressure ............................................ 14
Log Set Installation .................................15
FlameAdjustment ................................16
Wall Thermostat..................................... 16
Remote Control.......................................16
Decorative Pipe .......................................17
System Check ...........................................17
Operation ................................................. 18
Maintenance ...........................................19
Glass Replacement.............................19
Optional Blower ................................... 20
Optional Antique Brick Kit ..................22
HighAltitudeAdjustment ...................23
MobileHomeInstallation ...................23
Illustrated Parts Breakdown ................24
Replacement Parts List..........................25
Warranty Statement............................. 26
Lighting Instructions .............................27
Jøtul GF 400 BV
Sebago
Gas Heater
ManufacturedandDistributedby:
Jøtul North America
Gorham,MaineU.S.A.
Your stove has a unique serial number stamped on the
rating plate which is hung on the back. Please record
the serial number in the space below. You may also wish
to attach your purchase receipt to this page for future
reference.
MODELNAME:JøtulGF400BVGasStove
SERIALNUMBER:_______________________________
DATEOFPURCHASE:____________________________
AUTHORIZEDDEALER:__________________________
ADDRESS___________________________________
PHONE:____________________________________
INSTALLER:__________________________________
FUELTYPE:____________________________________
FUELCONVERSION:NO_______YES_____
NOTES:________________________________________
______________________________________________
______________________________________________
______________________________________________
Test Standards
This appliance complies with National Safety
standards and is tested and listed by Intertek
TestingServicesofMiddleton,Wisconsinto
ANSIZ21.88-2009,ANSIZ21.88/CSA2.33-2009,and
CAN/CGA2.17-M91,CSAP.4.01.2forCanada.
DONOTATTEMPTTOALTERORMODIFYTHE
CONSTRUCTION OF THE APPLIANCE OR ITS
COMPONENTS.ANY
MODIFICATIONOR
ALTERATION WILL VOID THE
WARRANTY, CERTIFICATION
AND LISTING OF THIS
APPLIANCE.

4
138301_Rev_G 10.4.11
Jøtul GF 400
This appliance is an atmospherically-vented gas
fireplace heater designed only for vertical venting
directly to the outside of the house, using listed, Type
B-vent pipe.
Input Rates
THIS FIREPLACE IS SHIPPED FROM THE FACTORY
FOR USE WITH NATURAL GAS ONLY. FOR USE
WITHPROPANE,THEAPPLIANCEMUSTFIRSTBE
CONVERTED USING #156005 FUEL CONVERSION KIT
PROVIDED. CONVERSION SHOULD BE MADE BEFORE
THE APPLIANCE IS INSTALLED. SEE PG. 11.
WithShortLegs,reduceheightby21/4”(51mm)
13”
330 mm
Rear Exit
231/2”
597 mm
C
L
63/4”
171 mm
24”
609mm
28”
711 mm
263/4”
679mm
13”
330 mm
41/2”
114mm
131/4”
336mm
C
L
261/2”
673mm
L
C
BV Sebago
Specifications
Manifold Pressure: MIN. MAX.
Natural Gas: 1.2 WC (.30 kPa) 3.8 WC (.95 kPa)
Propane: 2.9WC(.722kPa)11.0WC(2.74kPa)
PiezoIgnitor/StandingPilot
Inlet Pressure: MIN. MAX.
NaturalGas: 5.0WC(1.24kPa)7.0WC(1.74kPa)
Propane: 12.0WC(2.99kPa)14.9WC(3.71kPa)
Propane
 40,000BTU/hr.maximuminput
 20,000BTU/hr.minimuminput
Natural Gas
  40,000BTU/hr.maximuminput
 22,000BTU/hr.minimuminput

5
138301_Rev_G 10.4.11
General Information
THIS HEATER MUST BE INSTALLED AND MAINTAINED
BY A QUALIFIED SERVICE AGENCY.
The installation and repair of this appliance must be
done by a qualified service person. Failure to properly
install and maintain this heater could result in an
unsafe or hazardous installation, which may result in
afire,explosion,propertydamage,personalinjuryor
loss of life.
This appliance may be installed in an aftermarket
permanently located, manufactured (mobile) home,
where not prohibited by local codes.
This appliance is only for use with the type(s) of gas
indicated on the rating plate. This appliance is not
convertible for use with other gases, unless a certified
kit is used.
Cet appareil peut être installé dans un maison
préfabriquée(mobile)déjàinstalléeàdemeuresiles
règlements locaux le permettent.
Cet appareil doit être utilisé uniquement avec les
types de gas indiqués sur la plaque signalétique.
Ne pas l’utiliser ave d’autres gas sauf si un kitde
conversion certifié est installé.
This appliance should be inspected before use and
atleastannually.Morefrequentcleaningmay
be required due to excessive lint from carpeting,
bedding material, etc. It is imperative that control
compartments, burners, and circulating air
passageways of the appliance be kept clean.
THISAPPLIANCEMUSTNOTBECONNECTEDTOA
CHIMNEYORFLUESERVINGANYOTHERAPPLIANCE.
The installation must conform to local codes. Your
local Jøtul dealer can assist you in determining
what is required in your area for a safe and legal
installation. Some areas require a permit to install
a gas burning appliance. Always consult your local
buildinginspector,orauthorityhavingjurisdiction,to
determine what regulations apply in your area.
CODECOMPLIANCE:Yourlocalofficialshavefinal
authority in determining if a proposed installation
is acceptable. Any requirement that is requested by
thelocalauthorityhavingjurisdiction,thatisnot
specifically addressed in this manual, defaults to local
code. In the absence of local codes, the installation
requirements must comply with the current edition
of National codes. In the U.S., these requirements
are established in the National Fuel Code, ANSI
Z223.1.(NFPA54)currentedition.InCanada,the
codeshavebeenestablishedinCAN/CGAB149Fuel
Installation Code, current edition.
Glass Panel
Do not operate this appliance with the glass
front removed, cracked, or broken. Replacement
of the glass should be done by a licensed or
qualified service person. Only remove glass for
routine service. Always handle glass carefully.
Consult the local or national installation code(s) to
assure that adequate combustion and ventilation air is
available.
Installer l’appareil selon les codes ou reglements
locaux, ou, en l’absence de tels reglements, selon les
Codesd’installationCAN/CGA-B149.
DO NOT OPERATE THIS STOVE IF ANY PART HAS BEEN
UNDER WATER. Call a qualified service technician to
inspect the heater and to replace any part of the con-
trol system and any gas control which may have been
under water.
Ne pas se servir de cet appareil s’il a ete’ plonge dans
l’eau, completement ou en partie. Appeler un tech-
nicien qualifie pour inspecter l’appareil et remplacer
toute partie du syste’me de controle et toute com-
mande qui ont ete plonges dans l’eau.
HardwareBagContents
• FuelConversionKit-LP..................................156005
• DecorativePipeMountingBrackets(4) ......129469
• RockWool,.006kg...........................................224136
Unpacking your stove
1. Remove the Top Plate of the stove by simply lifting it
straight off of the stove body.
2. To open the firebox, disengage the two Glass Frame
Latches located on top of the firebox. Pull each handle
forward to clear the latch from the notch in the frame.
Glass Frame
Latch
3. Familiarize yourself with the installation requirements
specified in this manual, before beginning the installa-
tion.

6
138301_Rev_G 10.4.11
Location
In selecting a location for the stove, consider the
following points:
1) Heat distribution
2) Vent termination requirements
3) Gas supply line routing
4)Trafficareas,furniture,draperies,etc.
This appliance may be located on or near conven-
tional construction materials, however, proper clearance
to combustibles must be maintained in order to provide
adequate air circulation around the appliance. Also, it is
important to provide adequate access around the stove
for servicing and proper operation.
The clearance and hearth specifications listed in this
manual are the minimum requirements for combustible
material. A combustible material is anything that can
burn (i.e. sheet rock, wall paper, wood, fabrics etc.). These
surfaces are not limited to those that are visible and also
include materials that may be located behind non-com-
bustibles.
If you are not sure of the combustible nature of a
material,consultyourlocalfireofficials.“FireResistant”
materials are considered combustible: they are difficult to
ignite,butwillburn.Also,“fire-rated”sheetrockisconsid-
ered combustible.
Hearth Requirements
TheGF400BVgasstoveCANNOTbeinstalleddirectlyon
carpeting, vinyl, linoleum or Pergo®.
If this appliance will be installed on any combus-
tible material OTHER THAN WOOD, a floor pad must be
installed that is either metal or wood, or a listed hearth
pad. This floor protection must extend the full width
and depth of the appliance. It is not necessary to remove
carpeting, vinyl or linoleum from underneath the floor
protection. See fig. 1.
Figure 1. Minimum Hearth Protection.
14”
(356mm)
27”
(686mm)
Safety Information
Due to the high operating temperatures this appliance
shouldbelocatedoutoftrafficandawayfrom
furniture,draperies,etc.Maintainproperclearanceto
combustible mantels and fireplace trim.
Childrenandadultsshouldbealertedtothehazards
ofhighsurfacetemperaturesandshouldstayawayto
avoid burns or clothing ignition.
Enfants et adultes doivent être avertis des dangers des
températuresdesurfaceélevéesetdevraientresterà
l’écart pour éviter les brûlures ou l’inflammation des
vêtements.
Youngchildrenshouldbesupervisedwhiletheyare
inthesameroomastheappliance.Toddlers,young
children and others may be susceptible to accidental
contactburns.Aphysicalbarrier,suchasachild
guard,isrecommendedtobeusedifthereareat-risk
individuals in the house. To restrict access to a fireplace
orstove,installanadjustablesafetygatetokeep
toddlers,youngchildrenandotherat-riskindividuals
outoftheroomandawayfromhotsurfaces.
Lesjeunesenfantsdoiventêtresurveilléspendant
qu’ils sont dans la même pièce que l’appareil. Les
tout-petits,lesjeunesenfantsetd’autrespeuventêtre
sensibles aux brûlures par contact accidentel. Une bar-
rièrephysique,commeungardedel’enfant,estrecom-
mandépourêtreutilisésiilyadespersonnesàrisque
danslamaison.Pourrestreindrel’accèsàunecheminée
ouunpoêle,installerunebarrièredesécuritéréglable
pourgarderlestout-petits,lesjeunesenfantsetautres
personnesàrisqueàsesortirdelasalleetàl’écartdes
surfaces chaudes.
Any safety screen or guard removed for servicing an
appliance must be replaced prior to operating the
appliance.
Tout écran ou grille de protection pour l’entretien d’un
appareil doit être remplacé avant de faire fonctionner
l’appareil.
Clothing or other flammable materials should not be
placed on or near the fireplace.
Surveillerlesenfants.Garderlesvêtements,les
meubles,l’essenceouautresliquidesàvapeur
inflammables lin de l’appareil.
Neverallowanyonetousethefireplaceiftheyare
unfamiliarwithitsoperation.
NEVER store or use gasoline or any other flammable
vapors or liquids in the vicinity of this appliance.
Neverburnanysolidmaterials(wood,cardboard,paper,
coal,etc.)inthisappliance.Usewithnaturalgasor
propane fuel ONLY.
Do not slam or strike the glass panel.
ThisapplianceisNOTforusewithaftermarketglassdoors.
Cet appareil ne sert pas avec des portes en verre de
marché des accessoires.
Wear gloves and safety glasses while installing or
performing maintenance procedures on this appliance.

7
138301_Rev_G 10.4.11
Stove and Vent
Clearance Requirements
Minimum Clearances from the Stove
to Combustibles See figs. 2-3.
Rear: 3”(76mm)-measuredfromDraftHood
Ceiling: 321/4”(819mm)-measuredfromstovetop
Corner: 3”(76mm)-measuredfromstovetop
Sides: 3”(76mm-measuredfromstovetop)
Venting
Allsides:1”(25mm)
All vent components must be installed in accordance with
the manufacturer’s instructions and within the terms of
their listing. Refer to the manufacturer’s instructions for
approved clearances from the vent pipe to combustible
materials.
Minimum Alcove Dimensions
Maintain clearances to combustibles as noted above.
Width: 32”(81cm)
Depth: 24”(61cm)
Height: 61”(155cm)
ApprovedWallPass-Through
Useonly4”SimpsonDura-VentWallThimble#3143to
passtheventpipethroughcombustiblewalls.Seefig.2.
Figure 3.Vent adaptor centerline at minimum clearance
to corner walls.
Figure 4. Mantel and Trim specifications -
Stove installed with Top Plate flush with fireplace face.
Stove shown with standard legs. With Short Legs, subtract
2 1/4” (51 mm) from the clearances indicated below.
MantelClearances-
3”
(76mm)
3”
(51 mm)
To Rear Wall
Figure 2. Parallel Installation Clearances.
3”
(76mm)

























13 “
33 cm
13 “
33 cm
37/8“to8”
9.8 cm to 20.3 cm
Figure 2. Approved Wall Pass-Through, Simpson Dura-Vent
Wall thimble #3134.
43/4”
12 cm
3”
(76mm)
3”
(76mm)
91/2”
(251 mm)
91/2”
(251 mm)

8
138301_Rev_G 10.4.11
Vent Requirements
The Jøtul GF 400 BV Sebago is specifically designed to
operateusing4”TypeBventpipecomponentsoraListed
Flexible gas liner.
• Allventingcomponentsmustbeinstalledin
accordance with the terms of their listing and
manufacturer’s instructions.
• Theminimumheightofaverticallyterminatedsystem
shall be no less than 7 feet, and the maximum height
shall be no more than 35 feet. See diagrams page 9.
• Withsteeproofs,nearbytrees,andinpredominant
windy conditions, poor draft or down draft conditions
can occur. In these cases, increasing the height of the
vent or high wind termination caps may improve the
situation.
• ELBOWS:Ifanoffsetorelbowisnecessaryinthe
vertical rise, it is important to support the vent pipe
every three feet, to avoid excessive stress on the
offsets.
• Wheneverpossibleuse45°elbowsopposedto90°
elbows. This offers less restrictions for the flow of flue
gases.
 Maximumnumberof90°elbows:three
Maximumnumberof45°elbows:four
• TOTALMAXIMUMHORIZONTALRUNANYWHEREIN
THEVENTINGCONFIGURATIONIS4FEET.Thedistance
betweenany45°elbowsisconsideredahorizontalrun.
See diagrams, page 10.
• AnyTypeBventpassingthrougharoofmust have
a flashing, storm collar, thimble and a Type B cap is
required. See diagrams, page 10.
• VentingontheSebagoCANNOTbelessthan4”in
diameterorgreaterthan4”indiameter.
• Anyunusedflueormasonryenclosurecanbeusedasa
passage way for venting, but the flue must be relined
usingTypeB4”ventorListedFlexibleGasLiner.
• Theremainingspacearoundthelinerinamasonryor
zero-clearance flue CANNOT be used to vent any other
appliance.
• WhenterminatingthroughtheroofrefertotheGas
Vent Rule for proper vent termination height.
See fig. 5.
• NOventingmayterminatehorizontallyorbelow
roof eaves.
• Passagethroughcombustibles(walls,ceilings)
must be with Type B venting and must maintain
listed clearances. The Jøtul GF 400 BV Sebago stove
isapprovedforuseonlywith4”SimpsonDura-
VentWallThimble#3143tomaintainpropervent
clearances.
• Anyhorizontalrunshouldhaveanupwardslopeof
1/4”perfoottowardtheterminationcap.
• Whenventingthroughathimbleintoamasonry
flue, any venting exposed in the room must be Type
Bventing,oraflexiblelinersleevewithin24ga.6”
stove pipe.
• ListedFlexibleGasLinersmaynotbeexposedinany
living space.
Figure 5. Termination Height Requirements.
Roof Pitch in Ft.
Flatto6/12........................ 1.0
Over6/12to7/12 ............. 1.25
Over7/12to8/12.............. 1.5
Over8/12to9/12............. 2.0
Over9/12to10/12 ........... 2.5
Over10/12to11/12........... 3.25
Over11/12to12/12 ........... 4.0
Over12/12to13/12........... 5.0
Over14/12to16/12.......... 6.0
Over16/12to18/12.......... 7.0
Over18/12to20/12 ......... 7.5
Over20/12to21/12.......... 8.0

 














 




9
138301_Rev_G 10.4.11
• When6”diameterdecorativepipeisinstalledto
cover the venting any Listed Flexible Gas liner must
be connected directly to the stove’s draft hood.
• Useofsinglewallconnectorpipeasaventisprohib-
itedforusewiththeGF400SebagoB-Ventstove.
• Afirestopisrequiredateveryfloor.
• Anyventingthatisexposedabovethefirstfloor,
regardless of attic space or living space, must be
enclosed. Always maintain the required clearance
from all sides of the vertical vent system according
to manufacture.
• Installationofanycomponentsnotmanufacturedor
approved by Jøtul or failure to meet all clearance re-
quirements will void all warranties and could result
inpropertydamage,bodilyinjury,orseriousfire.
• Nevermodifyanyventingcomponent,oruseany
damaged venting product.
• THEGASAPPLIANCEANDVENTSYSTEMMUSTBE
VENTED DIRECTLY TO THE OUTSIDE OF THE BUILD-
ING,ANDNEVERATTACHEDTOACHIMNEYSERVING
A SOLID FUEL OR GAS BURNING APPLIANCES.
• BESURETOMAINTAINTHEPROPERCLEARANCESTO
COMBUSTIBLESASDEFINEDINTHISMANUALAND
IN THE INSTRUCTIONS PROVIDED WITH EACH VENT-
INGCOMPONENT.
• Wheninstallingatanaltitudeabove2000’themini-
mumverticalrisebecomes12’fromthedrafthood.
Figure 6.Venting through a masonry chimney.
Listed termi-
nation cap
required
Storm collar
required
Recommended
damper sealing plate
to seal flue chamber
to prevent heat loss
Always
maintain
the proper
clearance to
mantel and
trim
Maximum
offsetis4ft.
Type B vent or
Listed Flexible Gas
Liner.
Use of Type B
vent liner within
outside chimneys
is recommended to
help keep the gases
warm and stabilize
draft.
Max.Height35ft.
Min.Height7ft.
Top sealing
achor plate
WARNING: FAILURE TO POSITION THE PARTS IN ACCOR-
DANCE WITH THIS DIAGRAM OR FAILURE TO USE ONLY
PARTS SPECIFICALLY APPROVED WITH THIS APPLIANCE
MAY RESULT IN PROPERTY DAMAGE OR PERSONAL
INJURY.
Venting through a Masonry or
Prefabricated Manufactured
Chimney
NOTE:
A chimney system located outside the building
envelopemaybesubjecttodowndrafting
and/orflowreversal.Atmospherically-ventedap-
pliances,suchasB-Vents,maynotbecompatible
withthesechimneysystems.
Allatmospherically-ventedappliances(B-Vents)
are affected by atmospheric conditions and house
pressurization.Forexample,aB-Ventappliance
vented to an outside chimney system in a base-
mentwilllikelybesubjecttonegativepressure.
This type of installation is not recommended.

10
138301_Rev_G 10.4.11
ApprovedB-VentConfigurations
Listed B-Vent Termi-
nation Cap required.
Maximum
total horizontal
anywhere
in venting
configuration
is4feet.
Listed B-Vent
Termination
Cap required.
Max.Four,45°
orThree,90°
Elbows
Figure 10.
Figure 9.
Figure 8.
Figure 7.
Listed B-Vent
termination cap
required.
Minimum
chimney height
from Draft Hood
is 7 feet.
Maximum
horizontal off-
set anywhere
in venting
configuration
is4feet.
Listed B-Vent
termination cap
required.
Max.Four,45°
orThree,90°
Elbows
Minimum
chimney height
from Draft Hood
is 7 feet.
Minimum
chimney height
from Draft Hood
is 7 feet.
Maximum
chimney
height off
Draft Hood is
35 feet.
Minimum
chimney
height off
Draft Hood is
7 feet.
NOTE:
Installation at
altitude greater
than 2000’ re-
quires minimum
12ft.vertical rise
from Draft Hood.
Maximum
total horizontal
offset anywhere
in venting
configuration is
4feet.
NOTE:
Installation at
altitude greater
than 2000’ re-
quires minimum
12ft.vertical rise
from Draft Hood.
NOTE:
Installation at
altitude greater
than 2000’ re-
quires minimum
12ft.vertical rise
from Draft Hood.
NOTE:
Installation at
altitude greater
than 2000’ re-
quires minimum
12ft.vertical rise
from Draft Hood.

11
138301_Rev_G 10.4.11
Fuel Conversion Procedure
1. Turn off gas supply to stove.
2. Remove the stove Top Plate.
3. Disengage the two Glass Frame Latches at the top of
the firebox. See illustration on page 5. Carefully lift
the glass panel up and out of the stove.
4. Ifinstalled,removetheEmbersandLogSetusingcare
not to damage the fragile log parts.
5. Lift out the Burner Skirt shown in fig. 11.
6. ReachunderthestoveandremovetheAirShutter
wingnut from its stud. See fig. 12.
Conversion Kit Contents:
• 1,regulatortowerlabeledforpropane
• 3,regulatortowerscrews
• 1,burnerorifice(3.20mmforNG,#49forLPG)
• 1,pilotorifice(#51forNG,#30forLPG)
• LabelA-tobecompletedandappliedto  
the back of the stove
• LabelB-applytothestove’sRatingPlate
• Smallvalvelabel-applytovalvebody
Conversion instructions are also shipped in the stove with the
conversion kit.
Fuel Conversion
The Jøtul GF 400 BV gas stove is shipped from the factory
equipped to burn NATURAL GAS only. If PROPANE gas is
to be used as fuel, the appliance must first be converted
forusewithpropane.UsePropaneConversionKit156005,
supplied with the appliance.
OrderandinstallNGConversionKit156006tochange
back to use with natural gas.
WARNING:
THE CONVERSION KIT IS TO BE INSTALLED BY
AN AUTHORIZED JØTUL SERVICE TECHNICIAN
IN ACCORDANCE WITH THE MANUFACTURER’S
INSTRUCTION AND ALL CODES AND REQUIRE-
MENTS OF THE AUTHORITY HAVING JURISDIC-
TION. FAILURE TO FOLLOW THESE INSTRUC-
TIONS COULD RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE. THE QUALIFIED AGENCY
PERFORMING THIS WORK ASSUMES RESPONSI-
BILITY FOR THIS CONVERSION.
IN CANADA:
THE CONVERSION SHALL BE CARRIED OUT IN
ACCORDANCE WITH THE REQUIREMENTS OF
THE PROVINCIAL AUTHORITIES HAVING JU-
RISDICTION AND IN ACCORDANCE WITH THE
REQUIREMENTSOFTHECAN1-B149.1AND.2
INSTALLATION CODE.
AVERTISEMENT:
Cet equipement de conversion sera installe par
une agence qualkfiee de service conformen-
ment aux instructions du fabricant et toutes
exigences et codes applecables de l’autorises
avoirlajuridiction.Sil’informaitondanscette
Instructionn’estpassuivieexactement,un
feu,explosionouproductiondeprotoxydede
carbone peut resulter le dommages causer de
propriete,perteoublessurepersonnelledevie.
L’agence qualifiee’ de service est esponsable
de l’installation propre de cet equipement.
L’installation n’est pas propre et complete
jusqu’al’operationdel’appareilconvertiest
cheque suivant les criteres etablis dans les
instructions de proprietaire provisionnees avec
l’equipement.
Figure 11. Lift and remove the Burner Skirt from within
the firebox.
Burner Skirt



Figure 12. Locate and remove the Air Shutter wingnut
from under the right side of the stove.
Tools required:
• 1/2”openendedwrenchordeep-wellsocket,TorxT20
orslottedscrewdriver,4mmallenwrench.

12
138301_Rev_G 10.4.11
7. Lift out the Burner Plate: NOTE: There are no screws
securing the Burner to the floor of the firebox. Pull
the Air Shutter forward and lift the burner together
with shutter up and out of the stove as a unit. See fig.
13.
8. ChangetheBurnerOrifice.Usinga½”openended
wrench or deep-well socket, remove the burner orifice
from its brass elbow housing and replace with the ap-
propriateorificesuppliedinthekit.Seefig.14.
9. Replace the Air Shutter and push it all the way back to
allow replacement of the Burner Plate. Reattach the
wingnut and gasket to the shutter stem under the
stove, but do not tighten. You will set its final position
later.
10. Replace the Burner Plate. Engage the burner tube
withtheAirShutterassemblyasinfig.14.Besure
the burner is securely engaged with the two support
brackets at the front of the firebox and push the plate
back toward the rear of the firebox.
11 . CHANGE THE PILOT ORIFICE: From within the firebox,
remove the Pilot Head by pulling it straight up from
thepilotbase.Seefig.16.Usingthe4mmhexkey
included with the kit, unscrew the pilot orifice (coun-
terclockwise). Replace with the appropriate orifice:
12. Tighten orifice into the base of the pilot assembly. To
prevent bypass leaks, be sure the orifice is secured
tightly and flush with the base. Replace pilot head by
pushing it down onto the pilot base.
13. Replace the Variable Regulator. Using a Torx T-20
screwdriver, remove the three screws from the front
of the valve regulator. See fig. 17.
14.Removetheregulatortower,gasket,whiteplasticdisk,
and spring. See fig. 17.
Figure 13. Remove the Air Shutter and Burner as a unit.
Burner Plate
Air Shutter
Figure 15. Air Shutter Setting
Air Shutter
Opening
Dimension
Burner Plate
Air Inlet Tube
Figure 14. Change the Burner Orifice.
Burner
Orifice
Brass Elbow

13
138301_Rev_G 10.4.11
Gas Supply Connection
The gas supply line connection is made to the left side of
the front-mounted valve. The gas supply line should be
3/8”nptwitha1/2”diametersupply,ortheappropriate
size to provide sufficient gas pressure to the valve regard-
less of the input setting.
The use of Flexible Gas Appliance Connectors is ac-
ceptable in many areas in the U.S. However, Canadian
methods vary depending on local code.
ALLINSTALLATIONSMUSTCOMPLYWITHLOCALCODE
ORINTHEABSENCEOFLOCALCODE,MUSTCOMPLYWITH
THEMOSTRECENTEDITIONOFTHENATIONALFUELGAS
CODEANSIZ223.1/NFPA54ORCAN-B149.
All codes require a gas shut-off valve (gas cock) and
union, to be installed in the supply line, and in the same
room as the appliance. This allows for the disconnection
of the stove for servicing and maintenance. See fig. 18.
AT-HANDLEGASCOCKISREQUIREDIN
MASSACHUSETTSTOCOMPLYWITHCODE248CMR.
Securealljointstightlyusingappropriatetoolsand
sealing compounds. For propane units be sure to use
compounds that are propane resistant. Turn on gas sup-
ply and test for gas leaks using a soapy water solution or
electronic gas detector. Never use an open flame to check
for leaks.
15. Install the new regulator: Be sure the new gasket is
properly positioned and tighten screws securely.
16.Installtheidentificationlabelstothestovesothat
they can be seen by any person that may be servicing
the stove.
Label A: apply to back of stove.
Label B: apply to stove’s rating plate.
Small valve Label: apply to valve.
17. Reassemble the stove, apply gas to the system and
check for leaks using a soapy water solution or elec-
tronic gas detector.
NEVER USE AN OPEN FLAME TO CHECK FOR GAS LEAKS.
18.Correct gas pressure is essential for efficient and safe
operation of this appliance. Use a manometer to check
pressures as specified in the Gas Pressure section of
this manual (page 15).
19.AdjusttheAirShutter.Youwillneedtopositionthe
shuttertoprovideagas/airmixturethatwillachieve
the best flame picture with your particular installation.
Start with the shutter stem at the half-way position in
the slot in the bottom of the stove. See fig. 12. Pushing
the stem back will restrict air, while pushing it for-
ward will open the shutter and increase air. With some
experimentation, you will find the shutter position that
works best for your installation.
ALWAYS REFER TO THE LIGHTING INSTRUCTIONS ON THE
INSIDEBACKCOVEROFTHISMANUALWHENLIGHTING
YOUR STOVE.
BLOWERNOTE:Installtheoptionalblowerbeforecon-
necting the gas line in order to ensure adequate clear-
ancebetweenboth.
Valve
Figure 17. Regulator assembly.
Apply small conversion label.
Regulator
Tower
Figure 16. Pilot orifice removal and replacement.
Rubber
Gasket
Pilot Head
Orifice
Pilot Base
Retainer Clip

14
138301_Rev_G 10.4.11
Gas Pressure
Correct gas pressure is essential for efficient and safe
operationoftheGF400BVgasstove.Itisimportant
that the correct pressure is established at the time of
the installation. Proper gas pressure provides a consis-
tent flow of gas to the appliance and is instrumental in
checking for gas leaks.
Pressure Test: Attach a manometer to the appro-
priate test point on the valve. See fig. 19. The gauge
connections are located on the front of the valve under
theOn/Off/Pilot-knob.Gaugeconnectionsareidenti-
fied by:
E - for Inlet or Supply Pressure (the amount of gas
coming to the valve.)
A-forManifoldPressure(theamountofgasthat
is coming out of the valve to the burner.)
ALWAYS TEST PRESSURES WITH VALVE CONTROL
KNOB SET ON HIGH.
INLET GAS PRESSURES
(inches water column)
 MIN MAX
NATURAL GAS 5.0 7.0
 PROPANE 12.0 14.9
The appliance and its appliance main gas valve
must be disconnected from the gas supply piping
system during any pressure testing on that system
attestpressuresinexcessof1/2psig(3.5kPa).
The appliance must be isolated from the gas
supply line by closing its individual manual gas
shut-off valve (gas cock) during any pressure testing
of the gas supply piping system that is equal to or
lessthanpressuresof1/2psig(3.5kPa).
MANIFOLDPRESSURES
(inches water column)
MIN MAX
NATURAL GAS 1.2 3.8
PROPANE 2.9 11.0
Figure 19. Pressure test points.
Leak test:
1. Mixa50-50solutionofwateranddish
soap.
2. Light appliance- see lighting instructions
on the inside back cover of this manual or
on the stove’s rating plate.
3. Brushorsprayalljointsandconnections
with the soapy water solution.
4. Ifbubblesappearatanyconnectionor
seam or a gas odor is detected, imme-
diately turn gas control knob to the OFF
position.
5. Tightenorreconnecttheleakingjoint
and retest for any gas leaks.
Figure 18. Supply valve connection fittings.
E A














15
138301_Rev_G 10.4.11
Log Set Installation
Brick Kit Note: Install the optional Antique Brick Kit
155370beforeinstallingthelogset.Seepage22andthe
instructionsprovidedwiththatkit.
TheGF400BVlogsetmustbeinstalledbefore
operating the burner. The logset includes five log pieces,
and a bag of ember stones packaged inside the firebox.
To install the log set, remove the packaging and place the
partsinsidethefireboxasillustratedinfigures20-24.Do
not handle the log set with your bare hands. Always wear
gloves to prevent skin irritation from the ceramic fibers.
The ember stones realistically simulate glowing
coals when the burner is operating. These should be
spread evenly over the burner plate and around the logs.
DONOTOBSTRUCTTHEPILOTASSEMBLYOPENING.Do
not pile the embers against the burner skirt edges. See
fig.24.
Figure 20. Engage the holes in the underside ot the Right
Log with the peg in the burner skirt.
Figure 22. Install Left Log
Figure 23. Install Left Middle Log
Figure 24. Install Top Log
Figure 24a. Position embers loosely and maintain 1/4”
clearance from the burner skirt edges.
NOTE: You do not need to use all of the ember
stones. With experimentation, you will find the
arrangement and quantity of embers that works
best with your stove. Depending upon the char-
acteristics of your installation, it is possible that
too many ember stones can promote sooting on
thelogs.Adjustthequantityofemberstonesas
appropriate to maintain the best overall flame
picture and burner performance.
Pilot
Opening
DO NOT
OBSTRUCT
Figure 21. Engage the holes in the underside ot the Rear
Log with the two pegs in the burner skirt.
PN220647
PN220646
PN220645
PN220648
PN 220701

16
138301_Rev_G 10.4.11
 
Optional Wall Thermostat or
Remote Control
Use only a 750 millivolt DC two-wire circuit thermostat
with this appliance. The thermostat should be placed
in the same room as the heater, typically 5 feet off the
floor. Avoid drafty areas or any area that may affect the
accuracy of the thermostat.
The thermostat should be connected to the stove us-
ingaminimumof16gaugewirewithamaximumlength
of25feetofwire.
Connect the two thermostat wire leads to the two
left terminals on the terminal block located directly
above the ignitor button. Do not overtighten the con-
nections. IT IS NOT NECESSARY TO DISCONNECT ANY
OTHER WIRES.SeeFig.26.
Forthermostaticoperation,theOn/Off/T-Statswitch
on the back of the stove must be in the T-stat position,
and the pilot light must be running, as it is the power
source for the thermostat.
At the thermostat, the two wires should be connect-
ed to the two connection screws on the thermostat base
plate per the manufacturer’s instructions.
Remote Control
When using a remote, the remote receiver should be
wired to the terminal block the same way the thermo-
stat would be. See the instructions above.
Follow the operating instructions included with the
Remote Control unit.
CAUTION:
LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN
SERVICING THE CONTROLS. WIRING ERRORS CAN CAUSE
IMPROPER OR DANGEROUS OPERATION. ALWAYS VERIFY
PROPER OPERATION AFTER SERVICING THE APPLIANCE.
Figure 26. Valve and Accessory wiring diagram.
Flame Appearance / Air Shutter
Adjustment
This stove is shipped from the factory equipped to burn
Natural gas. If the stove has been converted for use with
propane,theAirShuttermayrequireadjustmentto
achieve the desired flame appearance. Other installation
related variables can also affect the flame picture.The Air
Shutter may be opened or closed to provide the best flame
picture for your specific installation.
Too large an air opening - the appliance will generate a
flamethatisblueandtransparent,oran“anemic”flame.
Too small an air setting - the appliance will generate
very long yellow flames resulting in soot. Sooting pro-
duces black deposits on the logs, on the inside walls of the
appliance, and potentially on the exterior termination cap.
Sooting is caused by incomplete combustion in the flames
and lack of combustion air entering the air shutter open-
ing.
AirShutterAdjustmentshouldbedoneonlybyaqualified
gas technician.
1. Reach under the right side of the stove and loosen the
wingnut located closest to you. See fig. 25. Slide the
wingnut stud forward to open the air shutter and back
toprovidelessair.Makeadjustmentsinsmallincre-
ments.
2. Tighten the wingnut to secure the shutter at the de-
sired setting.
3. Allow the stove to burn for 30 minutes on the HIGH set-
ting, observing the flame continuously. If the flame ap-
pears weak, slow, or sooty, repeat the process described
above until the flame is as desired.
Figure 25. Loosen the wingnut to adjust the air shutter.

TH
TP
TH
TP





ON
OFF
TSTAT
Yellow
Purple

White
Orange
Red
Black
White
Black






17
138301_Rev_G 10.4.11
System Check
1. PURGING THE GAS LINE: When lighting the appliance
for the first time, it will take a few moments to clear
the gas line of air. Once this purge is complete, the
appliance will operate as described in the lighting
instructions. See the inside back cover of this manual
or the stove Rating Plate attached the bottom of the
stove. Subsequent burner starts will not require purg-
ing the gas line unless the supply line is shut off.
2.PILOTFLAME:Youcanmonitorthepilotflame
through the view port located at the rear of the Right
Log. See fig. 28. The pilot flame should be steady - not
lifting or floating. The flame should be blue in color
around the pilot hood, with traces of yellow toward
the outer edges.
 Thepilotflameshouldengulfthetop3/8”ofthe
thermopile (to generate millivolt current) and the
top1/8”ofthethermocouple.Thepilotflameshould
projectoutofthepilothood1”atallthreeports.See
fig. 28.
3.BURNERADJUSTMENT:Thisstoveisequippedwith
avariablegascontrolvalvethatallowseasyadjust-
ment of the flame height appearance and heat
output.ToadjusttheflamebetweentheHIandLOW
setting,rotatetheHI/LOWknob,locatedinthecenter
ofthevalveface.Fireintensitycanbeadjustedupto
50% between the LOW and HIGH settings. See fig.
29.
 NOSMOKEORSOOTSHOULDBEPRESENT.CHECK
LOGPLACEMENTIFANYSOOTORSMOKEISPRESENT.
IFSOOTORSMOKEPERSISTS,THEAIRSHUTTERMAY
NEED TO BE ADJUSTED.
 SeeAirShutter/FlameAppearancesectionofthis
manualforproperairshuttersettingsandadjust-
ments. Note: the more offsets there are in the vent
system,thegreatertheneedforanairshutteradjust-
ment.Seepage16.

 





Figure 28. Proper pilot flame appearance.
Installing Decorative Pipe
The use of decorative pipe is optional. No decorative
pipeisincludedwiththeJøtulGF400BVSebago,
however, four locator brackets are included with the
stove in the hardware bag. The brackets are used to
center the decorative pipe over the draft hood on
which the pipe rests. Follow the procedure below to
attach the brackets to the stove.
1.Removethefour1/4”hexheadscrewsthatattach
the4”FlueCollartothedrafthood,butdonot
remove the Flue Collar. See Figure 27.
2.Alignthe“L”-shapedpipebracketswiththeholes
ontheFlueCollarandattachusingthefour1/4”
hexheadscrews,locatedintheMisc.Hardware
Bag.
Reminder: Do not use single wall stove pipe as the
vent pipe on this appliance.
Figure 27.
Decorative pipe attachment and Spill Switch location.







Decorative
Pipe Brackets
Spill
Switch

18
138301_Rev_G 10.4.11
Operation
FamiliarizeyourselfwiththecontrolsoftheGF400BV.
Makesurethatanyoneelseusingtheapplianceisalso
familiar with the controls and operation procedures.
Always follow the Lighting Instructions on the inside back
cover of this manual and also located on the Rating Plate
attached to the burner assembly.
1. Once the pilot is lit, burner operation is controlled by
the rocker switch located at the left corner of the rear
shroud. See fig. 30.
•ON/OFF-useformanualcontroloftheburner.
•T-STAT-useforoptionalthermostaticorremote
control operation. The burner will be controlled by
those accessories.
2. Duringthefirstfewfires,youmaynoticeodorand/
or smoke from the stove.This is normal and results
from burn-off of manufacturing residue and curing of
materials. You may find it helpful to provide additional
ventilation and fresh air to alleviate this condition.
3. Condensation may occur on the glass upon each
lightingoftheappliance.This“fog”willdisappearas
the appliance heats up.
4. Keepthecontrolsandtheareaundertheappliance
free of debris, vacuum this area frequently. Always keep
the appliance area clear and free from combustible
materials, gasoline and other flammable liquids.
Figure 29. Flame appearance on the “high” setting after
approximately 15 to 20 minutes burning.
WARNING:
AIRSHUTTERADJUSTMENTSSHOULDONLYBEPER-
FORMEDBYAQUALIFIEDPROFESSIONALSERVICE
TECHNICIAN.
Figure 30.
Burner Switch and
optional Blower
Controls
If a vacuum is used during any service on the stove,
ALWAYS be sure the stove is cold and there are NO hot
embers.
5. Remember, this appliance has a continuous burning
pilot flame. Exercise caution when using products
having combustible vapors. Always shut-off gas supply
while servicing the stove.
6. CAUTION: DO NOT OPERATE THIS APPLIANCE WITH THE
GLASSREMOVEDCRACKEDORBROKEN.
Replacement of the glass should be done by a licensed
or qualified service person. Use only replacement glass
provided by your authorized Jøtul dealer. Never use
any substitute materials.
WARNING: OBSERVE CAUTION WITH THE GLASS.
THEGLASSPANELMAYSHATTERUNEXPECTEDLYIF
STRUCK WITH AN OBJECT. ALWAYS HANDLE THE GLASS
PANEL WITH CARE. WHEN SERVICING THE STOVE
ALWAYSPULLTHEGLASSASSEMBLYSTRAIGHTUPFOR
REMOVAL.
7. Clean the glass only when necessary. Wipe surface
with a clean, damp soft cloth. Follow with a dry, soft
towel as desired.Take care not to scratch the glass
surface.
WARNING: DO NOT USE ABRASIVE CLEANERS ON THE
GLASS. NEVER CLEAN THE GLASS WHEN IT IS HOT.
CAUTION:
DO NOT ATTEMPT TO ALTER THE FLAME APPEARANCE
BY POSITIONING THE GAS VALVE CONTROL IN ANY
OTHER POSITION OTHER THAN THE FULL “ON”
POSITION.
NOTE: This appliance is equipped with a Spill Switch
which will disable the burner in the event that the
vent system becomes blocked. Located on the side of
the Draft Hood, at the back of the stove, the switch
has a reset button that, when pressed, will re-enable
burner function. See Fig. 27.
  IftheSpillSwitchrepeatedlyshutstheburner
off,turnoffthegassupplyandcallyourdealeror
service technician. The Spill Switch will continue to
shut off the burner until the vent problem has been
corrected. Not all vent problems can be corrected as
B-Vent appliances are affected by atmospheric condi-
tions and house pressurization.
BLOCKED FLUE SWITCH








19
138301_Rev_G 10.4.11
Glass Care
Clean the glass only when necessary. Wipe the surface
with a clean, dampened, soft cloth. Follow with a dry, soft
towel. Take care not to scratch the glass surface.
WARNING:
DO NOT USE ABRASIVE CLEANERS ON THE GLASS. NEVER
CLEAN THE GLASS WHEN IT IS HOT.
Gasket Inspection
It is important that the glass gasket be inspected at least
annually. Examine the ribbon gasket for signs of dete-
rioration and make sure the gasket has a positive seal.
Replace the gasket if necessary. Refer to the replacement
parts list on page 25.
REPLACE CRACKED OR BROKEN GLASS ONLY WITH
JØTUL
CERAMICGLASSREPLACEMENTKIT155599.DONOT
USE ANY OTHER TYPE OF GLASS WITH THIS APPLIANCE.
Figure 32. Wrap the gasket around the glass panel.
Maintenance
This stove and its venting system should be inspected
before use and at least annually by a qualified service
technician.
Usetheformonpage26tokeepamaintenancehis-
tory of your stove.
IMPORTANT:
ALWAYS TURN OFF THE GAS SUPPLY TO THE FIREPLACE
AND UNPLUG THE FORCED AIR BLOWER BEFORE ANY
SERVICE WORK IS PERFORMED ON THE FIREPLACE.
Annual Cleaning
Vent System
The entire vent system, including the chimney, should
be inspected and cleaned every year. If the intake and
exhaust venting is disassembled for any reason, it should
be reassembled and sealed according to the manufac-
turer’s instructions provided at the initial installation.
Burner and Logset
Periodically inspect the Firebox, Valve Compartment,
Convection Airways and optional Blower to BE CERTAIN
THATTHEFLOWOFCOMBUSTIONANDVENTILATIONAIR
IS UNOBSTRUCTED.
The firebox should be vacuumed annually to remove
any surface build up. Use a soft brush attachment and
handle the logs carefully as they are fragile. Be sure to
vacuum or wipe off the pilot assembly and burner sur-
faces.
Glass Panel or Gasket Removal
1. Lift the Top Plate off of the stove.
2. Release the two Glass Frame Latches. Pull each latch
handle forward forward to disengage the latch from
the notches in the glass frame.
3. Lift the glass frame all the way up and out of the top of
the stove. Lay this assembly on a flat surface, protect-
ing the frame from scratches using a blanket or towel.
3. The glass panel is held in place by four compression
clips. Use a screwdriver or small pliers to pry these up
off the edge of the glass retaining walls. See fig. 31.
4. Removetheoldgasketmaterial.Seefig.32.
Glass Panel or Gasket Replacement
1. Wrap the new gasketing material evenly around the
edge of the glass, peeling back the protective strip to
expose the adhesive as you go. Press the adhesive side
down onto the glass surface. Do not stretch the gasket.
2. Place the gasketed glass within the frame and press
each of the retainer clips back into place on the re-
tainer walls.
Figure 31. Use small pliers remove the four clips.

20
138301_Rev_G 10.4.11
THISBLOWERMUSTBEELECTRICALLY
GROUNDED IN ACCORDANCE WITH LO-
CAL CODES OR, IN THE ABSENCE OF LO-
CALCODES,WITHTHECURRENTANSI/
NFPA 70, NATIONAL ELECTRICAL CODE
OR CSA C22.1-CANADIAN ELECTRICAL
CODE.
THIS UNIT IS SUPPLIED WITH A THREE-
PRONG (GROUNDING) PLUG FOR PRO-
TECTION AGAINST SHOCK HAZARD AND
SHOULD BE PLUGGED DIRECTLY INTO A
PROPERLY GROUNDED THREE-PRONG
RECEPTACLE.DONOTCUTORREMOVE
THEGROUNDINGPRONGFROMTHE
PLUG.
ALWAYS DISCONNECT THE POWER SUP-
PLYWHENPERFORMINGANYSERVICE
ON THE FIREPLACE INSERT.
OptionalBlower#156000
Connectthegassupplylinetothestove,
beforeinstallingtheBlower.
Usea90°Elbowoffthecontrolvalvetocreate
clearancerequiredfortheblowerinstallation.
1. Unpack and check the contents of the blower kit.
Contact your dealer if any damage is evident or parts
are missing. See fig. 33.
2. Attach the Snapstat Bracket to the studs located in
themiddleofthefireboxfloorusingthetwoM6hex
nutsanda10mmwrench.Seefig.34.
3. Attach the Blower Bracket to the stove using the two
M6flangeheadhexboltsasshowninfig.34.
4. AttachtheDuctDeflectorsusingthetwo#7x1/2”
screws together with the finger guard mounting
screwsalreadyinplace.See#7and#11infig.33.
5. Install the Blower with the duct openings oriented
up and forward. See fig. 35. Feed the wire harness
through the bracket opening and secure the blower
to the bracket with the wing screw.
6.AttacheitherSnapstatwireconnectortoeither
Snapstat terminal. See fig. 35.
7. Install the Snapstat by sliding it all the way into the
slot in the bottom of the Snapstat Bracket as shown
infigs.34and35.
8. Connect the male wire harness connector to the fe-
male wire harness connector already installed in the
stove. See fig. 35.
9. Connect power cord to outlet.
Figure 34. Attach Snapstat and Blower Brackets.
Snapstat
Bracket
Blower Bracket
Hex Head
Flange Bolts
Hex Head
Flange Nuts
Figure 33. Blower Kit Components
Contents
1. Blower
2.MountingBracket
3. Snapstat Wire Harness
4.ControlSwitchWireHarness
5. Snapstat
6.SnapstatBracket
7. Blower Duct Deflector (2)
8.M6HexHeadFlangeNuts(2)
9.M6x12HexHeadFlangeBolts(2)
10.M6x12Wingscrew
11.#8x1/2”phillipsscrew(2)
Tools Required
•10mmwrench
* short phillips screwdriver
* Safety Glasses
* Work Gloves
5
3
1
6
4
7
7
11
10
2
8
9