Jøtul FS 173 User manual

Monterings- og bruksanvisningen må oppbevares under hele produktets levetid. These instructions must be kept
for future references. Ce manuel doit être conservé pour de futures interventions. Wir empfehlen Ihnen, die Mon-
tage- und Bedienungsanleitung für spätere Zwecke sorgfältig aufzubewahren.
Jøtul FS 173 - I 520
Manual Version P06
Jøtul FS 173- I 520
NO - Monterings- og bruksanvisning 4
UK - Installation and Operating Instructions 10
SE - Monterings- och bruksanvisning 16
FR - Manuel d’installation et d’utilisation 22
DE - Montage- und Gebrauchsanweisungen 28
PL - Instrukcja montażu i użytkowania 34

3
Følgende punkter er sjekket under/etter installasjonen:
OK Ikke OK
Er ildstedet montert etter monteringsanvisningen?
Er størrelsen/avstand til brannmur i henhold til mont. anvisningen?
Er avstand til brennbart materiale kontrollert?
Er avstand til tak kontrollert?
Er underlagsplate/forplatens størrelse i henhold til mont. anvisningen?
Tåler gulvet vekten av ildsted med omramming?
Er røykinnføring/innmuringsstuss montert?
Er røykrøret montert med stigning fra ildsted mot skorstein?
Er ildstedet sikret tilstrekkelig tilførsel av forbrenningsluft?
Er det fjernet et ildsted?
Er tidligere hull i skorsteinen forskriftsmessig fjernet?
Er ildstedet prøvefyrt og fungerer tilfredsstillende?
Installasjonen er utført av:
OBS! Husk at huseier plikter å melde fra til kommunen ved Brann og Feiervesen om at ildsted er monterti følge
norsk regelverk
Sørg derfor at denne side blir utfylt og at en kopi sendes til det stedlige Brann og Feiervesen samt tagodt vare
på originalen da denne er et verdipapir for boligen.
Dette er forutsetningenfor at Jøtuls JDUDQWL er gjeldende.
Meldeskjema og sjekkliste for montering av ildsted
Eiers navn
Eiendommens adresse:
Ildstedets navn og type:
Skorsteinstype (eks. tegl, element eller stålskorstein):
Gnr.Bnr.
Tlf.
Maks. effekt i kW Brenseltype
Høyde fra røykinnføring til skorsteinstopp og innvendig diameter):
Meter Dia. Ø mm
Antall ildsteder på skorsteinen:
Stk.
Post nr. Sted
Sted Dato Eiers signatur

10
ENGLISH
Fig. 1
Combustible wall
Non combustible wall
Jøtul JGFW-5 Firewall
Min. installation measurements
1000
1000
1000
50
837
500
910
300
271
50
100
787
960
500 350
1424
987
700
70
341
900155-P01
Ø 110
160
Min. floor plate measurements X / Y Acc. to national standards and regulations
Optional hole in floor for Ø 100 mm outside air connection
530
574
2350 (Ceiling)
1698
795
530
271
1386
500490708
530

11
ENGLISH
1.0 Relationship to the
authorities
The Jøtul FS 173 is a freestanding product using the Jøtul
I 520 as the burn chamber, and can be positioned against
combustible walls at the distances described in Fig. 1.
The installation of a fi replace must be carried out in
compliance with national laws and regulations. All local
ordinances must also be complied with when products
are installed.
Contact your local building authorities regarding restrictions
and installation requirements.
The product may not be used until it has been inspected
and approved by qualifi ed personnel.
The product has been tested and documented as a freestanding
stove in accordance with EN 13240.
The approval label for the freestanding product comes with
the installation instructions for the surround. Cut off the label
and attach it outside the top rear plate.
2.0 Technical data for
the burnchamber
Material: Cast iron
Finish: Black paint
Type of fuel: Wood
Max. log length: 50 cm
Smoke outlet: Top outlet or 45° rotated
position for rear outlet.
Flue pipe dimension: Ø 150 mm/177 cm2 cross
section
Weight approx.: 110 kg + 261 kg
Optional extras: Adapter for outside air
connection and Kit for Ø 80
fresh air intake tube.
Product dimensions, clearances See Fig. 1
Technical data in accordance with EN 13240
Nominal heat output: 7 kW
Effi ciency: 77%
CO emissions (13% O2): 0.07%
CO emissions (13% O2): 884 mg/Nm3
OGC emissions (13% O2): 60 mg/Nm3
Dust emissions (13% O2): 14 mg/Nm3
Flue gas temperature: 305°C
Flue gas fl ow rate: 7.1 g/s
Chimney draught, EN 13229: 12 Pa
Recommended draught
with smoke outlet: 16-18 Pa
Fuel consumption: 2.3 kg/h
Kindling quantity; nominal 1.7 kg
Max. kindling: 3.4 kg each time and 3.8 kg/h
Operation: Intermittent
Intermittent operation means normal use of a fi replace. This
means that to refuel the fi re, you add more wood as soon as
the previous load of wood has burned down to embers.
Contents
1.0 Relationship to the authorities ................11
2.0 Technical data ........................................11
3.0 Safety .....................................................12
4.0 Installation ..............................................13
5.0 Assembly ................................................14
6.0 Installation completed ............................14
7.0 Opional extras ........................................14
8.0 Recycling ................................................14
les combustibles recommandés.
Respectez les consignes d'utilisation. Utilisez uniquement
Verwenden Sie nur empfohlenen Brennstoffen.
Montage- und Bedienungsanleitung beachten.
Follow user`s instructions. Use only recommended fuels.
standard
Certificate/
The appliance can be used in a shared flue.
Minimum distance to adjacent combustible materials:
Emission of CO in combustion products
Serial no: Y-xxxx, Year: 200x
Manufacturer:
N-1602 Fredrikstad
Norway
Jøtul AS
POB 1441
Sweden
EUR Intermittent
Nominal heat output
Norway
Country
Operational type
Fuel type
Operation range
Efficiency
Klasse II
Classification
Standard
Flue gas temperature
Room heater fired by solid fuel
Product:
Jøtul
SP Sveriges Provnings- och
221546
Forskningsinstitut AB
SP Swedish National
Testing and Research
Institute
:
Approved by
:
:
:
:
:
:
:
Minimum distance to adjacent combustible materials:
OGC SP
EN
Serial no.
On all our products there is a label
indicating the serial number and year.
Write this number in the place indicated
in the installation instructions.
Always quote this serial number when
contacting your retailer or Jøtul.

12
ENGLISH
The surround consists of the following
parts (fi g. 2):
Part Description Qty
1 Guide pin Ø6X25 8 stk
2 Woodscrew Ø6x80 EZ 8 stk
3 Hex Cap Screw DIN933-M8x16-8.8 Zinc Plated 24 stk
4 Hex Flange Nut M6 DIN6923 8 4 stk
5 Distance sleeve 4 stk
6 Brakett front 1 stk
7 Bracket left side middle uprofi le 1 stk
8 Profi le side øvre uprofi l 2 stk
9 Firewall FS 173 2 stk
10 Bracket for height adjustment 2 stk
11 Bracket right side middle uprofi le 1 stk
12 screen plate part FS 173 1 stk
13 Height adjustment screw M8x54 1 stk
14 Bottom Plate 1 stk
15 Lower Anchoring Profi le 1 stk
16 Upper Anchoring Profi le 1 stk
17 Upper Binding Profi le 1 stk
18 Top Upper Anchoring Profi le 1 stk
19 Top Front Anchoring Profi le 1 stk
20 Bracket front uprofi le 2 stk
21 Steel plate back low 2 stk
22 Soapstone side upper R 1 stk
23 Soapstone front up 2 stk
24 Soapstone lower front 2 stk
25 Soapstone side low left 1 stk
26 Soapstone side lower right 1 stk
27 Soapstone side middle L/R 2 stk
28 Soapstone side upper L 1 stk
29 Sector valve pl compl FS 173 1 stk
30 Soapstone FS 173 1 stk
31 Steel support for soapstone 1 stk
35 Sector valve upper part 1 stk
36 Sector valve lower part 1 stk
3.0 Safety
NB! To guarantee optimal performance and safety, Jøtul
recommends that its stoves are fi tted by a qualifi ed installer
(see www.jotul.com for a complete list of dealers).
Any modifi cations to the product may result in the product and
safety features not functioning as intended. The same applies to
the installation of accessories or optional extras not supplied by
Jøtul. This may also be the case if parts that are essential to the
functioning and safety of the fi replace have been disassembled
or removed.
In all these cases, the manufacturer is not responsible or liable
for the product and the right to make a complaint becomes null
and void.
3.1 Fire Prevention
Measures
There is a certain element of danger every time you use
your fi replace. The following instructions must therefore
be followed:
• The minimum safety distances when installing and using
the fi replace are given in fi g. 1.
• Ensure that furniture and other fl ammable materials are not
too close to the fi replace. Flammable materials should not
be placed within 1 metre of the fi replace.
• Allow the fi re to burn out. Never extinguish the fl ames with
water.
• The fi replace becomes hot when lit and may cause burns
if touched.
• Only remove ash when the fireplace is cold. Ash can
contain hot embers and should therefore be placed in a
non-fl ammable container.
• Ash should be placed outdoors or be emptied in a place
where it will not present a potential fi re hazard
3.2 Floor
Foundation
Make sure that the foundation is strong enough to bear the
weight of the fi replace (110 kg + 274 kg).
We recommend the removal of any fl ooring that is not attached
to the foundation (“fl oating fl oors”) beneath the installation.
Requirements for protection of wooden
fl ooring beneath the fi replace
The product has integrated fl oor protection and may therefore
be placed directly on a wooden fl oor.
Requirements for protection of
combustible fl oors in front of the
fi replace
The front plate must comply with national laws and regulations.
Contact your local building authorities regarding restrictions and
installation requirements.
3.3 Walls
Distance to walls made of combustible materials - see fi g. 1.
The fi replace may be used with a semi-insulated fl ue pipe provided
the distances between the fi replace and walls made of combustible
materials are as shown in fi g. 1.
NB: Make sure that furniture and other household items are not
so close as to get dried up by the stove.

13
ENGLISH
3.4 Ceiling
If the ceiling above the fi replace is made of a combustible
material, the minimum distance between the fi replace and ceiling
must be 650 mm. i.e. a minimum ceiling height of 2350 mm.
3.5 Air circulation
There must be a fl ow of air between the burn chamber and the
surround. This is to ensure that any build-up of heat inside the
surround is not too great. NB: It is extremely important not to
cover air openings. See Fig. 1 for distances.
The amount of combustion air for Jøtul’s products is
approximately 25-40 m3/h.
3.7 Steel chimney
If a top-mounted steel chimney is used, a semi-insulated
chimney must be installed all the way down to the insert.
Fig. 2
Then fi t the steel chimney in accordance with the manufacturer’s
instructions.
• The insert must be connected to a chimney and fl ue pipe
approved for solid fuel fi replaces with a fl ue gas temperature
of 305°C.
• The cross-sectional area of the chimney must be at least that
of the fl ue pipe. Ø 150 mm/177 cm2 cross-sectional area.
• Several solid fuel products can be connected to the same
chimney system if the cross-sectional area of the chimney is
adequate. Contact your local building authorities regarding
restrictions and installation requirements.
• The chimney must be connected in accordance with the
installation instructions of the chimney supplier.
• Make sure that the fl ue pipe rises all the way up to the
chimney.
• Please note that it is extremely important for connections to
have a degree of fl exibility.
The recommended chimney draught is 16 - 18 Pa.
4.0 Installation
NB: Before installing the fi replace, check it carefully for any
signs of damage.
NB: The product is heavy! Ask someone to help you when
positioning and installing it.
NB: Read the Installation and Operating Instructions for the
Jøtul I 520 (Cat. no. 10046368) and Jøtul FS 173 (Cat. no.
10048557) carefully before installing the fi replace!
Use the acrylic sealant provided for all joints!
4.1 Prior to installation
The basic product comes in two packages:
1. Burn chamber.
2. Soapstone units with mounting sections.
NB: Check the product for signs of damage when you unpack it.
Preparations
Before installation, it is necessary to decide:
• Where the smoke outlet is to be located.
• Possible use and location of external air supply.
Refer to manuals for installation of the parts.
Smoke outlet
Before starting installation work, decide whether a rear or top
outlet will be used. The product is delivered from the factory
with the smoke outlet positioned for a top outlet.
4.2 Preparations for the
burnchamber (Jøtul I 520)
NB: Before installing the fi replace, check it carefully for any
signs of damage. The product is heavy! Ask someone to help
you when positioning and installing it.
Read the Installation and Operating Instructions for the Jøtul I
520 (Cat. no. 10046368).

14
ENGLISH
5.0 Assembly
NB: The base must be leveled. Max. 1 mm/m tolerance. This is
extremely important to ensure that the rest of the installation is
correct.
Important!
Please note that rough handling may damage the soapstones.
The mounting brackets should be attached with care. Installation
should be carried out by a qualifi ed person.
Useful tools for installation.
Spirit level, Allen key, ruler, cap wrench, rubber mallet, hammer
and screwdriver.
Fig. 5
6.0 Installation
completed
Refer to the “Installation manual with technical data”
for the Jøtul I 520 (Cat. no. 10046405) for use and
maintenance of the product!
6.1 Maintenance
Maintenance work must only be performed when the fi replace
is completely cold.
Soapstone: Scratches on the surface can be rubbed away using
fi ne sandpaper. Deeper scratches in the stone can be fi lled
using a paste made of powdered soapstone and water glass.
7.0 Optional extras
Adapter for air supply and outside air
connection.
Cat. no. 22046792 (DE)
Cat. no. 21046789
8.0 Recycling
8.1 Recycling the packaging
Your fi replace is delivered with the following packaging:
• A wooden pallet that can be cut up and burned in the
fi replace.
• Cardboard packaging that should be taken to a local
recycling facility.
• Plastic bags that should be taken to a local recycling facility.
8.2 Recycling the fi replace
The fi replace is made of:
• Metal that should be taken to a local recycling facility.
• Glass that should be disposed of as hazardous waste. The
glass in the fi replace must not be placed in a regular source
segregation container.
• Vermiculite burn plates that can be disposed of in regular
waste containers.

40
• Flytt luftinntak (A) til undersiden (Se fi g. 4 i manualen for Jøtul I 520).
• Move the air intake connector (A) to the underside of the burn chamber (See Fig. 4 in the manual for
Jøtul I 520).
• Flytta luftintag (A) til kaminens undersida (se bild 4 i bruksanvisning fôr Jøtul I 520).
• Déplacer la prise d´air (A) à la partine infèrieure. (Voir fi g. 4 dens le manuel pour le Jøtul I 520).
• Installeer het luchttoevoer (A) aan de onderkant van het product. (Zie afb. 4 - Jøtul I 520 Installatiehandleiding
en Gebruiksaanwijzing)
• Montieren Sie Den Lufteinlass (A) an die Produktunterseite (Siehe Abb 4 in der Montage und
Gebrauchsanweisung für Jøtul I 520).
• Zmień położenie króćca dopływu powietrza (A) na dół komory spalania (patrz Rys. 4 w instrukcji Jotul I 520)
1
2
1
2
A
5 mm
5 mm
5 mm
5 mm
5 mm
5 mm
1
2
NO: Uteluftstilførsel / SE: Frisklufttillförsel / UK: External air supply /
FR: Connexion de l’air de combustion extérieur – / DE: Frischluftzufuhr /
NL: Buitenluchtverbinding / PL: Dopływ powietrza zewnętrznego

41
•
Montering / assembly / Installation

42

43
90o
90o
34 mm

44

45

46

47

51

Jøtul arbeider kontinuerlig for om mulig å forbedre sine produkter, og vi forbeholder oss
retten til å endre spesifi kasjoner, farger og utstyr uten nærmere kunngjøring.
Jøtul bemüht sich ständig um die Verbesserung seiner Produkte, deshalb können
Spezifi kationen, Farben und Zubehör von den Abbildungen und den Beschreibungen in der
Broschüre abweichen.
Jøtul pursue a policy of constant product development. Products supplied may therefore
diff er in specifi cation, colour and type of accessories from those illustrated and described
in the brochure.
Jøtul s’attache à l’amélioration constante de ses produits. Ceux livrés peuvent présenter
quelques diff érences d’aspect, de couleur et d’accessoires par rapport au présent document.
Kvalitet
Vår kvalitetspolitikk skal gi kundene den trygghet og kvalitetsopplevelse som Jøtul har stått
for siden bedriftens historie startet i 1853.
Qualität
Unsere Qualitätspolitik vermittelt unseren Kunden ein Gefühl von Sicherheit und Qualität, für
das Jøtul mit seiner langjährigen Erfahrung seit der Firmengründung im Jahre 1853 steht.
Quality
Our policy gives our customers quality and safety piece of mind as a result of Jøtul’s vast
experience dating back to when the company fi rst started in 1853.
Qualité
Notre démarche assure à nos clients une tranquillité d’esprit sur la qualité et la sécurité,
due à une expérience remontant à la création de la société en 1853.
Jøtul AS,
P.o. box 1411
N-1602 Fredrikstad,
Norway
www.jotul.com
Cat.no. 10048557-P06
Jøtul AS, Oct. 2018