J2 KuDo 6T Original instructions

WARNINGS&SAFETYINFORMATION:
PLEASEREADCAREFULLYANDKEEPACOPYONTHEPROPERTYFORFUTUREREFERENCE!
GeneralSafetyInformation
• Toreducetheriskofdeath,personalinjuryorpropertydamagefromfire,electricshock,falling
parts,cuts/abrasions,andotherhazardsreadallwarningsandinstructionsincludedwithandon
thefixtureboxandallfixturelabels.
• Beforeinstalling,servicing,orperformingroutinemaintenanceuponthisequipment,follow
thesegeneralprecautions.
• Commercialinstallation,serviceandmaintenanceofluminairesshouldbeperformedbya
qualifiedlicensedelectrician.
• ForResidentialinstallation:Ifyouareunsureabouttheinstallationormaintenanceofthe
luminaires,consultaqualifiedlicensedelectricianandcheckyourlocalelectricalcode.
• DONOTINSTALLDAMAGEDPRODUCT!
• ThisfixtureisintendedtobeconnectedtoaproperlyinstalledandgroundedULlistedjunction
box.
WARNING:
RISKOFELECTRICALSHOCK
• Turnoffelectricalpoweratfuseorcircuitbreakerboxbeforewiringfixturetothepowersupply.
• Turnoffthepowerwhenyouperformanymaintenance.
• Verifythatsupplyvoltageiscorrectbycomparingitwiththeluminairelabelinformation.
• MakeallelectricalandgroundedconnectionsinaccordancewiththeNationalElectricalCode
andanyapplicablelocalcoderequirements.
• AllwiringconnectionsshouldbecappedwithULapprovedwireconnectors.
CAUTION:
RISKOFINJURY
• Wearglovesandsafetyglassesatalltimeswhenremovingluminairefromcarton,installing,
servicingorperformingmaintenance.
• Avoiddirecteyeexposuretothelightsourcewhileitison.
• Accountforsmallpartsanddestroypackingmaterial,asthesemaybehazardoustochildren.
CAUTION:
RISKOFFIRE
• Keepcombustibleandothermaterialsthatcanburnawayfromluminaireandlamp/lens.
• MIN90°CSUPPLYCONDUCTORS.
Illustrationsareforinstallationpurposesonly.Theymaynotmatchcompletelythefixture
purchasedaswearemakingcontinuousimprovements.Consulteitherwebsiteorfactoryif
youshouldhaveanyquestions.
KuDo 6T™
1
©2019J2LightInc.Becauseofcontinuingproductimprovementprograms,J2LightInc.reservestherighttochange
specificationswithoutnotice.Tel780‐701‐4140 /Websitewww.J2Light.com

Step4.PlacethetwoLIFTRAILSontothe2FTendsoftheT‐Barforeither2'x4'or2'x2'grids.
Placeontothe1FTendsfora1'x4'grid.TheLIFTRAILSshouldfitsnugtothebottom
corneroftheT‐Barasshown(belowleft).FastentheLIFTRAILtotheT‐Barwithaselfdrilling
screwtosecurethroughoneofthethreepilotholesprovided(belowright).
EnclosedyoushouldfindonecompleteKuDo 6T™newtrofferconsistingof:
1. KuDo 6T™Lightfixturebodywithmountingbolthinges.
2. 2xT‐BarMounting“LIFTRAILS”
3. 1xDriverCoverwithspliceplatefornewT‐Barinstallation.
**Fastenersand12gaugehangerwiresbyothers.
Step3.YournewKuDo 6T™isprovidedwith2x
“CALILIFTRAILS”asshowntotheright.Each
railhasslottedtracksandtwoscrewtabs.
OrientwithscrewtabsupwhenplacingonT‐
Barunderoldfixture.
Step1.Toavoidelectricalshock,disconnectpowertooldfixture.
Step2.Carefullyremovethefixturefromthepackaging.Inspectforanydefectsbefore
proceeding.
KuDo 6T™
Step5. For seismic jurisdictions you may be required to SecureNo.12hanger
wirefromeach“LIFTRAIL”tothebuildingstructure(below). Please follow national and local
building codes.
LeftRail
RightRail
ScrewTabs

LeftRail
EntrySlot DropSlot
KuDo 6T™
Slidethisway
Step6. LifttheKuDo 6T™bodysothatthebackisfacingtowardsyouwithhingeboltsattopleft
andtoprightcorners.AnglethebodysothatthetoplefthingeboltHEAD enterstheLeft“LIFTRAIL”
“EntrySlot”(below).Aftertheboltheadpassesthroughthe“EntrySlot”,slideitpartwaytoward
the“DropSlot”end.YoumaynowenterthetoprighthingeboltHEAD throughtheRight“LIFT
RAIL”“EntrySlot”.Slidebothboltheadstowardsthe“DropSlot”endandletthebodyhangdown.
RightRail
Step7. FastenbothaircraftcablesafetytetherslocatedonKuDo 6T™bodytotheNo.12Hanger
Wire(aboveinset).
SafetyTether

Step8. WithKuDo 6T™bodytetheredtothehangerwireandhangingfreelyyoumaynowsplice
buildingpower.TheKuDo 6T™isequippedwithadrivercoverthathasaremovablespliceplate
withtwo7/8”knockouts.Accessgroundandpowerdisconnectbyremovingspliceplate.Checkto
makesurebuildingvoltagematchesvoltageofferedbytheKuDo 6T™providedonthesafetylabel.
Splicegroundwirebeforesplicingbuildingpowerwires.
4
KuDo 6T™
KuDo 6TTM newtrofferincludesdriver
coverwithspliceplateandtwo7/8”
knockouts.
Step7.Raisethefixtureslowly
upwardasitpivotsonthe
hingeboltsneartheendofthe
LIFTRAILS.Gentlyliftthehinge
sideofthefixturebodytoslide
allthewayuptheendofthe
slotsontheLIFTRAILS.This
willallowtheoppositeedgeof
theKuDo 6T™closestyouto
cleartheT‐Barface.Raisethe
non‐hingesideabovetheT‐Bar
andslowlypullbackuntilyou
feelthehingebolts
dropintothe“DropSlot”.TheKuDo 6T™maynowbeallowedto
restontheT‐Bar(9).

5
KuDo 6T™
Step10.Remove
protectiveplasticfrom
lensanddispose.Ifyou
noticeanydebrisonthe
lens,removethelensand
cleanthedebris.Replace
lens.

6
PubRevision190302
NARROWGRIDCEILING(“L”SideRail)ACCESSORY
KuDo 6T™wasdevelopedforstandardT‐Bargridceilingswith15/16”face.Fornarrowgrid
ceilingsthatofferfaceslessthan15/16”,an“L”SideRailaccessoryisoffered.
Two“L”shapedsiderailsareprovided.NOTE:thesearetobeinstalledfirst.The“L”siderailssit
atopthe4ftsidesofthegridandareheldinplaceattheendsbythe“Lift”Rails.After“L”side
railsareinstalled,proceedtostep3.oftheinstallationfoundonpage2.
KuDo 6T™