Jackson Systems Wireless Comfort WCZ-600-T User manual

User Manual
Model WCZ-600-T
Wireless
COMF RTTM
Made in the USA
Inside
Mo
Schedule Day
AM
AUTO
Set To
Heat
MENU HOLD NEXT ENTER
Up and Down keys used when
adjusting temperature, time of day,
day of the week, program start times
and other options
SYSTEM key selects Heat, Cool,
Auto Heat/Cool, Off and
Emergency Heating for a
heat pump application
Fan key selects Auto or
Cont fan operation
Temperature Setting
Space temperature
Indicates Morn, Day, Eve
or Night schedule
Indicates the Schedule, Hold or
Permanent Hold mode
Menu key used to set time of
day, daily schedule, calibrate
temperature sensor and
display schedule.
Hold key used to switch
between Schedule and
Permanent H operation
Next key used when setting
time of day and schedules
Battery compartment, 2 AA batteries.
Enter key used when setting
time of day and schedules
SYSTEM
FAN
SYSTEM
FAN
Energy Savings
Wireless zone control
thermostat
The WCZ-600-T wireless thermostat is one of
up to six thermostats that has been installed
as part of the WCZ-600 Wireless Comfort™
zone control system. Each thermostat
communicates with the WCZ-600 zone
control panel which controls the heating,
cooling and ventilation system while directing
the right amount of conditioned air into each
zone through wireless communications with
zone dampers that open and close to
maintain the desired temperature setting in
each zone. Each WCZ-600-T thermostat
allows you to set separate separate
temperatures for heating and cooling for four
time periods per day (morning, daytime,
evening and night). Or, you can operate each
thermostat without using the schedule feature
(Permanent Hold Mode).
The schedule feature can save energy by
reducing heating and cooling when a zone is
not being occupied.

Factory Schedule
Morning
Day 8:00AM
Evening
Night
6:00AM
5:00PM
10:00PM
70F
62F
70F
62F
Heating
78F
82F
78F
82F
Cooling
Program Start Time Setpoint
Warning!
Selecting System
Off, Auto, Heat, Cool or EM HT
The thermostat relies on battery power for communications with the WCZ-600 zone control
panel. Change the batteries every year or whenever the low battery warning is displayed.
Press the key to select , (heating and cooling) (heating), (cooling)
or (emergency heating if your system is a heat pump).
In , the thermostat will call for heating or cooling based on the heating and cooling set
temperatures and the indoor temperature. To view both the heating and cooling set
temperature in mode, press the key. The LCD will display and then
along with the corresponding set temperature. Use the and keys to
change the set temperature when the proper mode is displayed.
Press the key to select or (continuous) fan operation. In the thermostat
activates the fan during heating and cooling calls. In the fan runs continuously to
circulate air.
System Off Auto Heat Cool
EM HT
Auto
Auto NEXT Heat Set To
Cool Set To UP DOWN
Fan Auto Cont Auto
Cont
This thermostat is shiped from the factory with the following programmable schedule.
Inside
AM
HEAT
Set To
MENU HOLD NEXT ENTER
System
Mode
AUTO
Heat
Selecting Fan
Auto or Cont
Inside
Th
AM
HEAT
Set To
MENU HOLD NEXT ENTER
Fan
Mode
AUTO
Mo
2

Selecting Schedule or
Permanent Hold
Press the key to switch between , and .
operation automatically changes the heating and cooling temperature settings at the four
scheduled times ( ).
When in operation, adjusting the heating or cooling temperature using the Up and
Down keys will switch the thermostat to the mode. After 3 hours the thermostat will return
to the mode or you can press the key at any time to switch to the
mode.
The mode maintains the heating and cooling temperatures indefinitely until the
key is pressed which will return the thermostat to the mode.
Press the UP and Down key to change the heating or cooling temperature. Press the Next key to
switch between the heating and cooling temperature.
Hold Hold Hold Permanent Schedule Schedule
Morning, Day, Evening and Night
Schedule
Hold
Schedule Hold Schedule
Hold Permanent
Hold Schedule
Inside
Schedule Day
AM
AUTO
HEAT
Set To
MENU HOLD NEXT ENTER
Schedule
Mode in
Day
Schedule
HOLD Key
Heat
Setting the Heating and
Cooling Temperature
Inside
Schedule Day
Th
AM
AUTO
HEAT
Set To
MENU HOLD NEXT ENTER
Cool
Schedule
Mode in
Day
Schedule
NEXT Key
Mo
3

To set the time of day and the day of the week, press the key and the LCD will display the
hour. Use the and keys to set the hour. Make sure that the AM or PM is correct.
Press the key to set the minute. Use the and keys to set the minute.
Press the key to set the current day of the week. Use the and keys to select the
day of the week and press the key.
Press the key twice until the LCD displays the schedule screen shown below with the
current day of the week. Press and hold the or key to change the morning ( )
schedule start time. The start time is in 15 minute increments. Make sure that the AM or PM is
correct.
Press the key to display the morning heating (Heat) temperature. Use the and
keys to change the temperature.
MENU
Up Down
NEXT Up Down
NEXT Up Down
ENTER
MENU
UP Down Morn
NEXT Up Down
Setting the Time
and Day
AM
CANCEL NEXT ENTER
Changing the Schedule
Schedule Morn
AM
MENU CANCEL NEXT
Schedule Morn
AM
Heat
Set To
CANCEL NEXT
Th
Mo
Mo
4

Press the key to display the morning Cooling (Cool) temperature. Use the and
keys to change the temperature.
Continue using the key and the and keys to set the start time, heating
temperature and cooling temperature for the , and schedules.
After the schedule is completed, you can press the key which will only save the
schedule for the current day or you can apply the same schedule to other days of the week by
pressing the key.
Each time you press the key an additional day will be added to the schedule. Use the
and keys to turn any day off that you don’t want as part of the schedule. Only the days
displayed on the thermostat will be copied to the schedule when you press the key. As
an example, you might want one schedule for the days of the week and a separate schedule for
the weekend.
After pressing the key the thermostat will return to normal operation. To change the
schedule for other days of the week, repeat the same programming steps. Each day of the week
can have a separate schedule if required. Just program the schedule, select the day then press
the key.
NEXT Up Down
NEXT Up Down
Day Evening Night
Night ENTER
NEXT
NEXT Up
Down
ENTER
ENTER
ENTER
Schedule Morn
AM
Cool
Set To
CANCEL NEXT
PM
Mo
Schedule Night
CANCEL NEXT ENTER
Mo
PM
Mo
Schedule
TuWe Th Fr
CANCEL NEXT ENTER
Night
5

Press the key 5 times until the first schedule is displayed as shown below. The display
will show the Monday morning schedule start time and heating temperature.
Continue pressing the key to display the morning, day, evening and night schedule along
with the heating and cooling temperatures for each day of the week. Press the key at
any time to exit and return the thermostat to normal operation.
MENU
NEXT
CANCEL
If you plan to leave for an extended period of time and want to save energy by placing your
Comfort System™ in Permanent Hold, it is not necessary to change all the thermostats in the
zoning system. The zone thermostat that has been assigned Zone Number 01 is the only
thermostat in the system that can be set for Vacation Mode. If you are unsure which thermostat
is Zone 01, there should be a label located on the subbase of each thermostat identifying its
zone number. Simply release the thermostat from its subbase by pressing up from the bottom
center and swinging it away. he thermostat identification label is located in the lower left hand
corner. If the installing contractor did not fill out the identification label, you can find the
thermostat zone address by accessing the thermostat Installer Options menu.
Reviewing the Time and
Temperature Schedule
Mo
Schedule Morn
AM
Heat
Set To
CANCEL NEXT
Vacation Mode
FILL OUT AND
AFFIX TO LOWER LEFT HAND CORNER
OF THERMOSTAT SUBBASE
Thermostat Zone #
Thermostat Home #
Location
1
1
Living Room
ZONE NUMBER
6

Caution! Do not make any changes to the Installer Options or your Wireless Comfort™
thermostat may fail to operate properly.
ENTER
ENTER
MENU
OFF UP DOWN
On ENTER
Zone One Controlling On
Permanent Hold
Continuous Fan
Permanent
Hold HOLD
Schedule
To access the thermostat Installer Options menu, press and hold the key for
approximately 5 seconds or until the following appears on the display.
If Option 01, Zone 01 appears, this is the correct thermostat. To exit the menu, press the
key.
To select Vacation Mode, press the key 3 times until the following appears on the display.
In normal operation, the Vacation Mode is . To turn it on, press the and keys until
the word is displayed and then press the key.
The thermostat will now display . You can place the thermostat in
and then set unoccupied heating and/or cooling temperatures. The zone one
thermostat now becomes the master control and all other zone thermostats are disabled. When
the thermostat calls for heating or cooling, all zones will receive conditioned air. If the thermostat
is set in the mode, all zones will receive ventilation air.
Upon return from an extended leave, the Vacation Mode must be turned off in order for all other
zone thermostats to have individual control. Remember to take the thermostat out of
if you want it to resume a pre-programmed schedule. Simply press the key until the
thermostat displays .
MENU HOLD NEXT ENTER
O1
O1
Zone
Option
MENU HOLD NEXT ENTER
Zone One
Controlling
OFF
MENU HOLD NEXT ENTER
Zone One
Controlling
O
7

5418 Elmwood Avenue, Indianapolis, IN 46203-6025
06-1064-060611
All rights reserved.
Jackson Systems, LLC 2010
Intellectual rights apply.
©
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference and (2) this device must
accept any interference received, including interference that may cause undesired operation.
If the battery voltage drops to where it could interfere with reliable operation, the thermostat LCD
will alternately display in place of the room temperature. Replace batteries immediately. It will
be necessary to reset the time of day and the day of the week after changing the batteries but
the schedule will not be affected as it is saved in non-volitile memory.
Even if communications is lost with every thermostat in your Wireless Comfort
Your Wireless Comfort
Lo
Inside Temperature
Calibration
™ zoning system,
the zone control panel will still be able to operate the HVAC system to maintain a preset heating
and cooling temperature as selected by your installing contractor to prevent freezing or
overheating of all zones.
™ thermostats have been accurately calibrated at the factory. However, if
the inside temperature displayed on the LCD requires re-calibrating, press the key 4
times until only the inside temperature is displayed on the LCD. Use the Up and Down keys to
change the inside temperature in 1 degree increments.
MENU
Caution: Re-calibrating the inside
temperature display requires the use of a highly accurate digital thermometer. Therefore,
it is recommended that you contact your heating and air conditioning contractor in the
event re-calibration is required.
Low Battery
Indication
Inside
Day
Th
AM
Heat
AUTO
Set To
MENU HOLD NEXT ENTER
Schedule
Inside
MENU HOLD NEXT ENTER
8