Jacques JEM-4 User manual

JEM-4 JACQUES INTERCOM BOX PRODUCT MANUAL
JED-0492
www |jacques.com.au

www |jacques.com.au
Document Number |JED-0492 Revision |1.0 Page 2 of 18
Disclaimer Notice
Every effort has been made to ensure that the information in this document is correct at the time of publication.
Jacques TechnologiesPty Ltd shall not be liable forany errorscontained in this document, norfor any incidental or consequential
damages that may occur in direct connection with the provision of this material.
This document does not constitute a product warranty, express or implied (including but not limited to, the implied warranty of
fitness for a particular purpose), or service guarantee.
Jacques Technologies Pty Ltd does not warrant or make any representations regarding the use, or the results of the use, of the
information provided within the publication in terms of its correctness, accuracy, reliability, or otherwise. No oral or written
information or advice given by Jacques Technologies Pty Ltd (or by its agents, contractors, distributors, or employees) shall
create a warranty or in any way increase the scope of this warranty. Some jurisdictions do not allow the exclusion of implied
warranties, so the above exclusion may not apply to you.
Jacques Technologies Pty Ltd acknowledges that information in this publication may be unsuitable in various circumstances and
disclaims liability for the use of the information in those circumstances.
Copyright Notice
Copyright © 2020 Jacques Technologies Pty Ltd. All rights reserved.
The material in every part of this document, and in its entirety, is protected by copyright.
No part of this document may be used, transmitted, reproduced, translated into another format, or adapted by any means or form,
in whole or in part, or for any purpose without express, written, permission from Jacques Technologies Pty Ltd.
No exceptions to these conditions will be made, except as permitted according to Australian and International copyright law.
Jacques Technologies Pty Ltd reserves the right to continually improve products and update the relevant equipment specifications
and documentation without notifying clients.
Trademarks
Products mentioned in this document may be trademarks of their respective companies and are hereby acknowledged.
Document Feedback
We value your feedback. To give feedback on this document please email [email protected]m.au
Publication Information
Document Number: JED-0492
Revision: 1.0
Release Date: 2020-09-28

www |jacques.com.au
Document Number |JED-0492 Revision |1.0 Page 3 of 18
CONTENTS
ABBREVIATIONS AND DEFINITIONS.......................................................................................................................................4
INTRODUCTION........................................................................................................................................................................5
FEATURES............................................................................................................................................................................5
APPLICATIONS.....................................................................................................................................................................5
OVERVIEW................................................................................................................................................................................6
CONNECTION DETAILS............................................................................................................................................................7
JIB-4000 REAR CONNECTIONS...........................................................................................................................................7
LED CONNECTIONS.............................................................................................................................................................8
RELAYS CONNECTIONS......................................................................................................................................................9
PERIPHERAL CONNECTIONS ...........................................................................................................................................10
TECHNICAL SPECIFICATIONS...............................................................................................................................................11
SAFETY WARNINGS...............................................................................................................................................................12
INSTALLATION INSTRUCTIONS.............................................................................................................................................12
MOUNTING SOLUTIONS.........................................................................................................................................................13
AGENCY REGULATORY NOTICES ........................................................................................................................................14
FEDERAL COMMUNICATIONS COMMISSION NOTICE ....................................................................................................14
DECLARATION OF CONFORMITY FOR PRODUCTS MARKED WITH THE FCC LOGO (UNITED STATES ONLY) .........14
CANADIAN NOTICE............................................................................................................................................................14
EUROPEAN UNION REGULATOR NOTICE........................................................................................................................15
DISPOSAL OF WASTE EQUIPMENT BY USERS IN PRIVATE HOUSEHOLD IN THE EUROPEAN UNION......................16
COUNTRY OF ORIGIN - QUALITY ASSURANCE ...................................................................................................................17
ORDERING INFORMATION.....................................................................................................................................................17
CONTACT DETAILS ................................................................................................................................................................17

www |jacques.com.au
Document Number |JED-0492 Revision |1.0 Page 4 of 18
ABBREVIATIONS AND DEFINITIONS
The following is a list of terms relevant to this document.
TERM
DEFINITIONS
ANM
Ambient Noise Monitor
AU/NZS
Standards Australia and New Zealand
EU
European Union
FCC
Federal Communication Commission
IEEE
Institute of Electrical and Electronics Engineers
IP
Internet Protocol
JEM-4
Jacques Ethernet Module Generation 4
JIB
Jacques Intercom Box
PA
Public Address
PoE
Power over Ethernet

www |jacques.com.au
Document Number |JED-0492 Revision |1.0 Page 5 of 18
INTRODUCTION
The JEM-4 Jacques Intercom Box (JIB-4000) is an alternative product offering to the standard offering
of Jacques panel type intercoms, providing customers a great range of customisation options. The
product enables users to interface to a Jacques IP intercom system with a customer supplied
arrangement of speaker, microphone, LED and buttons. In situations where a standard Jacques
intercom panel does not fulfill a required formfactor, the JIB-4000 will likely provide a solution.
Figure 1: JIB-4000 Front and Side View
FEATURES
•Balanced microphone level audio input (configurable for single-ended use)
•Class-D speaker amplifier output, 2.5 W @ 4 ohm
•Built in MEMS microphone
•2 external button inputs
•2 external LED outputs
•2 changeover relay contacts
•+12 V d.c., 200 mA max output supply
•IEEE 802.3af Power over Ethernet (PoE)
•LED indicators for troubleshooting
•Flexible mounting options
APPLICATIONS
•Convert customer provided speaker, microphone and button hardware to a intercom capable of
working with the Jacques IP audio system
•Suitable for space constrained installation

www |jacques.com.au
Document Number |JED-0492 Revision |1.0 Page 6 of 18
OVERVIEW
Figure 2: JIB-4000 Front View
The JIB-4000 product features a RJ45 port, LED indicators and a micro USB port on their front panel.
See below table for further description.
FRONT CONNECTIONS
LAN + PoE
RJ45 port for Data and Power
DIAG
Micro USB port intended for factory programming purposes
LED INDICATORS
PWR
When lit, indicates the devices internal power rails (5 V d.c. and 12 V d.c.) are
operational.
STAT
Indicates the devices current operational status / mode.
Typical modes:
Green: Call connected
Green Flashing: Server disconnected
Red: Device is operating in ‘Recovery Mode’
LINK
When lit, indicates ethernet link is detected
ACT
When lit, indicates ethernet data (TX / RX) activity
S1
N/A
S2
N/A
S3
When lit, indicates Relay 1 is activated
S4
When lit, indicates Relay 2 is activated
LINK
ACT

www |jacques.com.au
Document Number |JED-0492 Revision |1.0 Page 7 of 18
CONNECTION DETAILS
JIB-4000 REAR CONNECTIONS
Figure 3: JIB-4000 Rear Connections

www |jacques.com.au
Document Number |JED-0492 Revision |1.0 Page 8 of 18
LED CONNECTIONS
Figure 4: JIB-4000 LED Rear Connections
Pin
Signal
1
LED common anode (3.3 V d.c.)
2
LED 1 cathode
3
LED 2 cathode
Figure 5: LED connection mating plug
Pin 1

www |jacques.com.au
Document Number |JED-0492 Revision |1.0 Page 9 of 18
RELAYS CONNECTIONS
Figure 6: JIB-4000 Relay Rear Connections
Pin
Signal
1
Relay 2 Normally Open (NO) Contact
2
Relay 2 Common (COM) Contact
3
Relay 2 Normally Closed (NC) Contact
4
Relay 1 Normally Open (NO) Contact
5
Relay 1 Common (COM) Contact
6
Relay 1 Normally Closed (NC) Contact
Figure 7: Relay connection mating plug
Pin 1

www |jacques.com.au
Document Number |JED-0492 Revision |1.0 Page 10 of 18
PERIPHERAL CONNECTIONS
Figure 8: JIB-4000 Peripheral Connections
Pin
Signal
1
Speaker Negative
2
Speaker Positive
3
Audio Ground
4
Audio Input Negative
5
Audio Input Positive
6
Ground
7
Button input 1
8
Button input 2
9
Ground
10
+12 V Power Output
Figure 9: Peripherals connection mating plug
Pin 1

www |jacques.com.au
Document Number |JED-0492 Revision |1.0 Page 11 of 18
TECHNICAL SPECIFICATIONS
GENERAL
Power source
PoE IEEE 802.3af, Class 0
Power consumption
12 W max.
Standby power consumption
2.4 W idle
Form Factor
Rectangular metal enclosure (DIN Rail and Eurocard mounting brackets available)
Dimensions (W x H x D)
without terminations or brackets
(116 x 55 x 32) mm
Weight
Approx. 250 g
Operating temperature
(-20 to +70) °C
Storage temperature
(-40 to +85) °C
Relative humidity
Up to 95%, not condensing
INPUTS
Number of inputs
2
Logic
Active low (3.3 V CMOS)
RELAYS
Number of relays
2
Relay contact type
Changeover (NO, NC, COM)
Relay contact rating
Max. switching voltage:
60 VDC, 30 VAC 1)
Max. switching current (per output):
2 A
Max. switching power (per output):
60 W (DC), 37.5 VA (AC)
Expected life:
min. 105(30 VDC / 2 A),
min. 2 × 105(30 VDC / 1 A)
AUDIO CHARACTERISTICS
Max. Speaker Output Level
(Class D Bridge mode)
2.5 W RMS into 4 ohms
Output frequency response (-3 dB)
32 Hz - 13.6 kHz
Analogue Mic Input Impedance
6.4 kΩ balanced, 3.2 kΩ single-ended
Max. Analogue Balanced Mic Input Level
(AIN +, AIN -)
-20 dBu (220 mV p-p)
Max. Analogue Single-ended Mic Input Level
(AIN+, GND)
-20 dBu (220 mV p-p)
Analogue Mic Input frequency response (-3 dB)
15.9 Hz - 15.9 kHz
Audio codecs
Opus, G.711 A-law, G.711 µ-law, G.722, Jacques PCM
EXTERNAL CONNECTIONS
Ethernet / Power
1 x RJ45 port for Ethernet data and PoE (10/100/1000 Mbit/s)
Diagnostic Port
1 x Micro AB USB port for factory programming and diagnostics purpose only
Audio Input
1 x 3-way terminal block plug, 3.81 mm pitch
Audio Output
1 x 3-way terminal block plug, 3.81 mm pitch
Relay contacts
1 x 6-way terminal block plug, 3.81 mm pitch
CABLING
Ethernet
4 pair UTP Cat-5/5e/6, 24 AWG multi-strand conductors. T568A wiring scheme.
Relay contacts
To suit load and cable length 1.5mm2 max.
Balanced Audio
Screened cable (single pair)
Single Ended Audio
Screened cable
Inputs
To suit load and cable length 1.5mm2 max.

www |jacques.com.au
Document Number |JED-0492 Revision |1.0 Page 12 of 18
1) The relay output may only be connected to an ES1 or a SELV circuit! An ES1 circuit as per IEC/EN/UL 62368-1 or a SELV circuit as per
IEC/EN 60950-1 must be separated safely from a dangerous electrical circuit (e.g. 230 V or 110 V mains power), e.g. by means of double
insulation. The ES1 or SELV circuit must not exceed 60 VDC or 42.4 VACpeak (30 VACeff)!
SAFETY WARNINGS
•Observe the country-specific standards for installation, mounting and configuration.
•Only use Jacques accessories that comply with the product’s technical specifications.
•Disconnect the Ethernet cable for any maintenance of the device.
•Do not make any modifications to the device.
•All external connected circuits shall fulfil the requirements for Electrical Energy Source Class
1 (ES1) and Limited Power Source (LPS) according to IEC/EN 62368-1.
INSTALLATION INSTRUCTIONS
•See Mounting Solutions for methods of mounting a JIB product.
•Jacques JIB and optional accessories shall be installed or replaced by trained and qualified
personnel only.
•Before attempting to install please ensure your package contains the list of specified parts.
•Do not install the device on unstable walls or on surfaces which cannot support the device’s
weight.
•Make sure the surface mount kit not subject to torsional forces (e.g. on uneven walls).
•Avoid mounting unit in direct sunlight.
•Connect a network cable into the RJ45 connection located on the front of the product which
can also be connected to an IEEE 802.3af PoE PSE compliant network switch or
management device.
•Before powering the device, ensure all cables are correctly connected and not damaged.

www |jacques.com.au
Document Number |JED-0492 Revision |1.0 Page 13 of 18
MOUNTING SOLUTIONS
The following section highlights the available mounting options optionally available for JIB products.
Jacques P/N
Description
52235
Wall Mounting Kit
52236
DIN Rail Mounting Kit
52237
Eurocard Mounting Kit (accepts two units)
Figure 10: Surface Mounting Kit (P/N: 52235) fitted
Figure 11: DIN Rail Mounting Kit (P/N: 52236) fitted
Figure 12: Options for mounting multiple JIB-4000 using Eurocard Mounting Kit (P/N: 52236)

www |jacques.com.au
Document Number |JED-0492 Revision |1.0 Page 14 of 18
AGENCY REGULATORY NOTICES
FEDERAL COMMUNICATIONS COMMISSION NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•Consult the dealer or an experienced radio/TV technician for help.
DECLARATION OF CONFORMITY FOR PRODUCTS MARKED WITH THE FCC
LOGO (UNITED STATES ONLY)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
For questions regarding this FCC declaration, contact:
Jacques Technologies Pty Ltd
PO Box 3542,
South Brisbane BC QLD 4101, Australia
Or, call [phone]
To identify this product, refer to the Part, Series, or Model number found on the product.
CANADIAN NOTICE
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations. CAN ICES-3(B)/NMB-3(B)

www |jacques.com.au
Document Number |JED-0492 Revision |1.0 Page 15 of 18
EUROPEAN UNION REGULATOR NOTICE
Products bearing the CE marking comply with one or more of the following EU Directives as may be
applicable:
•Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on
the harmonization of the laws of the Member States relating to electromagnetic compatibility.
•Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the
restrictions of the use of certain hazardous substances in electrical and electronic equipment.
The following harmonized standards have been applied for the certification of conformity to the
guidelines listed above:
EN 55024:2010 + A1:2015
Information technology equipment –Immunity Characteristics –Limits and methods of measurements
EN 55035:2017
Electromagnetic compatibility of multimedia equipment –Immunity Requirements
EN 55032:2015
Electromagnetic compatibility of multimedia equipment –Emissions Requirements
EN 50581:2012
Technical Documentation for the assessment of electrical and electronic products with respect to the
restriction of hazardous substances.
For questions regarding this CE declaration, contact:
Jacques Technologies Pty Ltd
PO Box 3542,
South Brisbane BC QLD 4101, Australia
Or, call [phone]
To identify this product, refer to the Part, Series, or Model number found on the product.

www |jacques.com.au
Document Number |JED-0492 Revision |1.0 Page 16 of 18
DISPOSAL OF WASTE EQUIPMENT BY USERS IN PRIVATE HOUSEHOLD IN
THE EUROPEAN UNION
This symbol on the product or on its packaging indicates that this product must not be disposed of
with your household waste. Instead, it is your responsibility to dispose of your waste equipment by
handing it over to a designated collection point for the recycling of waste electrical and electronic
equipment.
The directive 2012/19/EU on waste electrical and electronical equipment (WEEE) is applicable in the
European Union member states.
The separate collection and recycling of your waste equipment at the time of disposal will help to
conserve natural resources and ensure that it is recycled in a manner that protects human health and
the environment. For more information about where you can drop off your waste equipment for
recycling, please contact the local city office, the household waste disposal service, or the shop where
you purchased the product.

www |jacques.com.au
Document Number |JED-0492 Revision |1.0 Page 17 of 18
COUNTRY OF ORIGIN - QUALITY ASSURANCE
Jacques products are developed and manufactured by Jacques Technologies Pty Ltd in Brisbane,
Australia. The development and manufacturing processes are certified in accordance with EN ISO
9001:2016. The technical data contained herein has been provided solely for informational purposes
and is not legally binding. Subject to change, technical or otherwise.
ORDERING INFORMATION
The Universal Audio Interface is supplied and shipped with the following components:
Jacques P/N
Model Number
Description
Base Models
52229
JIB-4000
Jacques Intercom Box
Spare Parts
J5142
N/A
3-way pluggable terminal block, 3.81 mm pitch
J1464
N/A
6-way pluggable terminal block, 3.81 mm pitch
J1152
N/A
10-way pluggable terminal block, 3.81 mm pitch
CONTACT DETAILS
Ph: [phone]
Email: [e-mail]
Website: www.jacques.com.au
ABN: 48 074 448 712

www |jacques.com.au
Document Number |JED-0492 Revision |1.0 Page 18 of 18
DOCUMENT REVISION HISTORY
REVISION
DATE
AUTHOR
CHANGE DESCRIPTION
1.0
2020-09-28
LM
Initial Release