JADO Glance 831/003 Series User manual

Installation Instructions
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Products Luxury Faucets and Accessories
6TEST INSTALLED FAUCET AND
CONNECTIONS FOR LEAKS
Remove AERATOR (3) from faucet.
With HANDLES (1) in OFF osition, turn on
WATER SUPPLIES (2) and check all
connections for leaks.
O erate both HANDLES to flush water
lines thoroughly. 1
2
2
O erate Lift Rod (5) and fill lavatory with water.
Check that DRAIN STOPPER (4) makes a
good seal and retains water in lavatory. Adjust
sto er height by re ositioning Lift Rod (5) and
tightening SET SCREW (6).
Release DRAIN STOPPER (4) and check all drain
connections and "P" tra for leaks. Tighten if
necessary.
Re lace AERATOR (3).
3
109646 109646
7HELPFUL HINTS FOR CLEANING AND MAINTENANCE
The solid brass product you have just purchased has been designed to give you years of beauty and service. It is
important to bring to your attention proper care and maintenance procedures, which will ensure its lasting beauty.
First and foremost, it is im ortant (as it is with any fine iece of jewelry or furniture) that the roduct be wi ed clean and
dry with a soft dam cloth after every use.
Second, under no circumstances should an abrasive cleaner or combination cleaner/ olish be used on JADO roducts.
The abrasive nature of such roducts will eventually destroy the finish and void the warranty.
In the event of stubborn blemishes shown on the finish, we recommend use of Windex window cleaner with a soft cloth,
but we do not recommend it be used on an everyday basis.
It is im ortant to note that it is normal to ex ect signs of usage over time.
Thank you for electing JADO for your home.
JADO
JADO
Widespread Lavatory Faucets
JADO USA
7845 East Paradise Lane
Scottsdale, AZ 8526O
Phone:(8OO) 227-2734
Fax: (8OO) 552-JADO(5236)
www.jadousa.com
Product Numbers
831/OO3/...
Glance
TO THE PURCHASER OF JADO BRASS PRODUCTS
Attention in taller:
Please leave This Pamphlet for The Owner
The state of California has mandated under Proposition #65 that
manufactures of products, including faucets which come into
contact with potable water, must warn the consumer if the product
contains materials listed by the state as a carcinogen or
reproductive toxin. Lead, which is contained in all brass faucets in
limited amounts appears on the State's list.
Preliminary industry tests have indicated that users of faucets
made from brass face no significant danger, however,
California Proposition #65 requires that we provide you with the
following notice:
NOTICE: JADO products conform to industry
requirements of water conservation under the
ASTM / ANSI A112.18.1M-1994 plumbing code.
Lavatory, bidet, wet bar and kitchen faucet sets
have a maximum flow rate of 2.2GPM. Shower
heads, hand showers and body sprays have a
maximum flow rate of 2.5GPM.
Warning: This product contains an element
known to the State of California to cause cancer
of reproductive harm.
JADO BATHROOM AND HARDWARE MFG.CORP.
7845 East Paradise Lane
Scottsdale, AZ 85260
4
5
6
POLISHED BRASS AND CUSTOM FINISHWARRANTY: A 1YEAR LIMITED FINISH WARRANTY from date of purchase is provided to the
first residential owner against defects in materials and workmanship. Due to the ever-changing finish of Patina products, the finish warranty
is excluded. Warranty shall not include problems related to the installation of the product.
MECHANICS
MECHANICAL WARRANTY: A LIFETIME LIMITED WARRANTY is provided to the first residential owner on parts to be free from failure
related to defects in materials and workmanship but not installation.
CONDITIONSTOWARRANTIES
JADO Bathroom & Hardware Manufacturing Corp.places the following conditions on its finish and mechanical warranties to the first residential owner only.
JADO finish and mechanical warranties are limited to products correctly installed and used in a residential environment.
JADO warranties will not assume liability for damage due to abuse, mishandling, incorrect installation, improper maintenance, or deterioration
due to normal use.
JADO will not be liable for labor or other costs relating to the sale, installation, or replacement of their products.
In the event of a defect in any JADO product covered by this warranty, the product must be returned to the dealer where originally purchased
along with proof of purchase.
JADO's obligation under the warranty shall be limited to the repair or exchange of any product which has been determined by JADO to be
defective after appropriate examination.
JADO warrants this product to be free from defects in materials or workmanship for as long as the original consumer purchaser
owns their home.
JADO will provide, free of charge, at it’s sole option, replacement part(s) or product (or if no longer available, a comparable
product) to replace those which have proven defective in materials or workmanship.
Proof of purchase (original sales receipt) from the original consumer purchaser must be made available to JADO for all limited
warranty claims.This limited warranty is non transferable.It does not apply in the event of product damage due to the use of other than
genuine JADO replacement parts, installation error, abuse, misuse, or improper care and maintenance (whether performed by
a plumber, contractor, service provider or member of the purchaser’s household).The limited warranty excludes damage due to aggressive
air or water conditions, or harsh or abrasive cleaners and/or materials.This limited warranty excludes all industrial, commercial and business
usage, whose purchasers are hereby extended a two year limited warranty (with the exception of solenoid valves and other electronic
components which carry a one year limited warranty) applying to all other terms of this limited warranty except duration. This limited warranty
does not cover labor charges incurred and/or damages sustained in installation, repair or replacement, nor incidental or consequential
damages, all of which are expressly disclaimed.This limited warranty is applicable only to JADO faucets manufactured after June 1, 1996
and installed in the United States and/or Canada.
This limited warranty gives the original consumer purchaser of an JADO faucet specific legal rights which may vary from state to
state or from province to province.This limited warranty does not cover any liability for consequential or incidental damages, all of which
are hereby expressly disclaimed, or the extension beyond the duration of this limited warranty of any implied limited warranties, including
those of merchantability or fitness for an intended purpose.In some states or provinces the exclusion or limitation of incidental or consequential
damages is not allowed, so those exclusions may not apply to you.
JADO Bathroom & Hardware Manufacturing Corp. provides the following warranties only to the first residential owner of our products.
FINISHES
JADO FAUCET LIFETIME FUNCTION AND FINISH LIMITEDWARRANTY

1SPOUT ASSEMBLY
2TEE AND HOSE ASSEMBLY
Insert SPOUT SHANK (1) through center
hole of sink or mounting surface. Make
sure RUBBER WASHER (2) is seated into
groove in SPOUT ESCUTCHEON BASE (3).
Assemble RUBBER WASHER (4),
FIBER WASHER (5) and LOCKNUT (6)
onto threads of SPOUT SHANK (1)
from underside of lavatory or mounting
surface.
Push the TEE (1) onto SPOUT SHANK (2) until it makes full contact
with the 0-RING (3)
Align SPOUT (7) and tighten
LOCKNUT (6). Insert LIFT ROD (8)
through SPOUT (7).
Insert POP-UP ROD (9) into bottom of
faucet and thread into POP-UP KNOB (10).
1
2
4
5
6
Turn off hot and cold water
upplie before beginning.
CAUTION
7
1
2
3
4
5
3
WATER SUPPLY CONNECTIONS
Connect water su ly to VALVE BODIES (1) with 1/2" IPS
FLEXIBLE SUPPLIES (3) or 3/8" O.D. BULL-NOSE RISERS (4).
Use wrench to tighten connections.
Do not over tighten. Be careful not to kink co er su ly when
bending. Use tubing cutter to cut to ro er length.
1
4
FERRULE
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE
PURCHASED SEPARATELY.
COUPLING
NUT
109646 109646
ROUGHING-IN
DIMENSIONS
Plumbers' Putty or Caulking
Adjustable Wrench
Philli s Screwdriver
Channel Locks
TOOLS REQUIRED
Tubing Cutter Regular Screwdriver
Basin Wrench
GROOVE
O-RING
O-RING
APPLY SEALANT
OR TEFLON TAPE
4A FOAM SEAL (1) is installed on underside of FLANGE (2). (Plumbers
Putty may be used in lace of FOAM SEAL (1) if desired.)
A ly sealant or Teflon ta e to threads of TAILPIECE (10) and
thread into DRAIN BODY (7) making a water tight seal.
Dro FLANGE (2) into LAVATORY DRAIN (3). From below assemble
RUBBER GASKET (4), PLASTIC WASHER (5) and LOCK NUT (6) onto
DRAIN FLANGE (2). Do not tighten fully.
INSTALL POP-UP DRAIN
FIG. 4a
FIG. 4b
FIG. 4c
FIG. 4c
FIG. 4a
FIG. 4b
1
4
3
2
5
6
7
8
6
9
2
Adjust STOPPER (13) height by re ositioning POP-UP ROD (16) in SWIVEL (15)
and tightening SET SCREW (18).
Assemble POP-UP SWIVEL (15) to PIVOT ROD (11) but do not tighten.
Dro POP-UP ROD (16) through other hole in POP-UP SWIVEL (15) and
tighten SET SCREW (17)
Assemble PIVOT ROD (11), and PIVOT NUT (12) as shown. Install CONCAVE
WASHER (19) into PIVOT ROD OPENING (9) if not reinstalled. Hand tighten
PIVOT NUT (12). Dro STOPPER (13) into drain.
(
To vandal proof drain rotate STOPP R (13) so PIVOT ROD (11) goes
through Y (14) of STOPP R (13) . Make connection to "P" TRAP.
Ins ect inside DRAIN BODY (7) that SEAL (8) is installed. Thread
DRAIN BODY (7) tight against FLANGE (2) to make a water tight seal.
10
9
7
6
12
19
16
1517
18 2
10
14
13
11
The PIVOT ROD OPENING (9) in DRAIN BODY (7) should face the rear
of the lavatory. Tighten LOCK NUT (6) on FLANGE (2) to make a water
tight connection with channel locks. Do not over tighten.
3INSTALL VALVE BODIES
INSTALL HANDLES
HOSE CONNECTIONS
1-3/4'' MAX.
STOP RING
GROOVE
Insert VALVE BODY (2) through mounting hole from underside
of tub deck or mounting surface.
Note: VALV BODY marked Hot is installed in the left Mtg. hole,
VALV BODY marked Cold in the right when facing front of fitting.
Maximum mounting surface thickness is 1-3/4".
Install STOP RING (6) onto VALVE BODY (2) if not in lace. Install
O-RING (7) into groove in FLANGE (8).
Thread FLANGE (8) flush against STOP RING (6). Thread
ROSETTE (9) onto VALVE BODY (2) until tight against it's
internal sto .
Align VALVE BODY (2) and from below tighten LOCKNUT (1)
to secure VALVE BODY (2).
Turn VALVES to off osition. Align HANDLES (10) as shown or
as desired and install onto HANDLE ADAPTER (11). Tighten SET
SCREW (12) with HEX WRENCH (13) su lied. Push PLUG
BUTTON (14) into lace.
Insert FIBER WASHERS (15) into COUPLING NUTS (16) of
SUPPLY HOSES (17) and tighten making water tight connection.
Important: Loop SUPPLY HOS S (17) as illustrated so they do not kink.
1
2
16
HOT
COLD
15
17
12
5
16
3
4
7
8
12 14
13
6
11
9
10
JADO
HOT
5-3/4"
3/4"
7-5/8"
6" to 12"
2-1/8"
1-1/4"
2"
max. 2"
4-1/2"
1-3/8" MAX.
1-1/2"
max. 7"
1/2" NPT
1-5/32"
5/8"
1-1/8"
NOTE: MOUNTING HOLES
ARE 1-1/4" D.
Thread LOCKNUT (1) to bottom of VALVE BODY (2). Make sure
SPACER (3), BRASS WASHER (4) and RUBBER WASHER (5) are
installed.
Un ack valve assembly and remove HANDLE (10) by unthreading
SET SCREW (12). Unthread ROSETTE (9) and FLANGE (8)
removing them from VALVE BODY (2).
3
810
9
Rotate TEE (2) about 10 degrees from center. Insert HEX
COUPLING NUT (4) into TEE (2) and tighten on end of s out
shank to make a water tight connection. Do not over tighten.
10˚