JADO Perlrand Series User manual

Installation Instructions
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
©JADO USA 2003
Products Luxury Faucets and Accessories
109434
109434
JADO USA
7845 East Paradise Lane
Scottsdale, AZ 8526O
Phone: 8OO) 227-2734
Fax: 8OO) 552-JADO 5236)
www.jadousa.com
Product Numbers
893/412/...
894/855/...
893/414/...
Perlrand
Roman Tub Fillers
Roman Tub Fillers
4MAKE WATER SUPPLY CONNECTIONS
4A
Remove AERATOR from FAUCET.
With HANDLES in OFF position, turn on
WATER SUPPLIES and check all connections
for leaks.
Operate both HANDLES to flush water lines
thoroughly.
Replace AERATOR.
Important: It is strongly recommended that
access be provided for all enclosed mechanical
parts to this system.
3/4" X 3/4" NPT UNION
(NOT SUPPLIED)
HOT
Connect HOT water supply to LEFT INLET
UNION (1) and COLD water supply to
RIGHT INLET UNION (2). Pipe connections
are 3/4" NPT. Use sealant or Teflon tape
on pipe connections.
Do not solder directly to valve body.
3/4" NPT
AERATOR
TEST INSTALLED FAUCET
5HELPFUL HINTS FOR CLEANING AND MAINTENANCE
The solid brass product you have just purchased has been designed to give you years of beauty and service. It is
important to bring to your attention proper care and maintenance procedures, which will ensure its lasting beauty.
First and foremost, it is important (as it is with any fine piece of jewelry or furniture) that the product be wiped clean and
dry with a soft damp cloth after every use.
Second, under no circumstances should an abrasive cleaner or combination cleaner/polish be used on JADO products.
The abrasive nature of such products will eventually destroy the finish and void the warranty.
In the event of stubborn blemishes shown on the finish, we recommend use of Windex window cleaner with a soft cloth,
but we do not recommend it be used on an everyday basis.
It is important to note that it is normal to expect signs of usage over time.
Thank you for selecting JADO for your home.
1
TO THE PURCHASER OF JADO BRASS PRODUCTS
Attention installer:
Please leave This Pamphlet for The Owner
POLISHE BRASS AN CUSTOM FINISH WARRANTY: A1 YEAR LIMITED FINISH WARRANTY from date of purchase is provided to the
first residential owner against defects in materials and workmanship. Due to the ever-changing finish of Patina products, the finish warranty
is excluded. Warranty shall not include problems related to the installation of the product.
MECHANICS
MECHANICAL WARRANTY: A LIFETIME LIMITED WARRANTY is provided to the first residential owner on parts to be free from failure
related to defects in materials and workmanship but not installation.
CON ITIONS TO WARRANTIES
JADO Bathroom & Hardware Manufacturing Corp. places the following conditions on its finish and mechanical warranties to the first residential owner only.
JADO finish and mechanical warranties are limited to products correctly installed and used in a residential environment.
JADO warranties will not assume liability for damage due to abuse, mishandling, incorrect installation, improper maintenance, or deterioration
due to normal use.
JADO will not be liable for labor or other costs relating to the sale, installation, or replacement of their products.
In the event of a defect in any JADO product covered by this warranty, the product must be returned to the dealer where originally purchased
along with proof of purchase.
JADO's obligation under the warranty shall be limited to the repair or exchange of any product which has been determined by JADO to be
defective after appropriate examination.
The state of California has mandated under Proposition #65 that
manufactures of products, including faucets which come into
contact with potable water, must warn the consumer if the product
contains materials listed by the state as a carcinogen or
reproductive toxin. Lead, which is contained in all brass faucets in
limited amounts appears on the State's list.
Preliminary industry tests have indicated that users of faucets
made from brass face no significant danger, however,
California Proposition #65 requires that we provide you with the
following notice:
NOTICE: JA O products conform to industry
requirements of water conservation under the
ASTM / ANSI A112.18.1M-1994 plumbing code.
Lavatory, bidet, wet bar and kitchen faucet sets
have a maximum flow rate of 2.2GPM. Shower
heads, hand showers and body sprays have a
maximum flow rate of 2.5GPM.
Warning: This product contains an element
known to the State of California to cause cancer
of reproductive harm.
JADO BATHROOM AND HARDWARE MFG. CORP.
7845 East Paradise Lane
Scottsdale, AZ 85260
JADO warrants this product to be free from defects in materials or workmanship for as long as the original consumer purchaser
owns their home.
JADO will provide, free of charge, at it’s sole option, replacement part(s) or product (or if no longer available, a comparable
product) to replace those which have proven defective in materials or workmanship.
Proof of purchase (original sales receipt) from the original consumer purchaser must be made available to JADO for all limited
warranty claims. This limited warranty is non transferable. It does not apply in the event of product damage due to the use of other than
genuine JADO replacement parts, installation error, abuse, misuse, or improper care and maintenance (whether performed by
a plumber, contractor, service provider or member of the purchaser’s household). The limited warranty excludes damage due to aggressive
air or water conditions, or harsh or abrasive cleaners and/or materials. This limited warranty excludes all industrial, commercial and business
usage, whose purchasers are hereby extended a two year limited warranty (with the exception of solenoid valves and other electronic
components which carry a one year limited warranty) applying to all other terms of this limited warranty except duration. This limited warranty
does not cover labor charges incurred and/or damages sustained in installation, repair or replacement, nor incidental or consequential
damages, all of which are expressly disclaimed. This limited warranty is applicable only to JADO faucets manufactured after June 1, 1996
and installed in the United States and/or Canada.
This limited warranty gives the original consumer purchaser of an JADO faucet specific legal rights which may vary from state to
state or from province to province. This limited warranty does not cover any liability for consequential or incidental damages, all of which
are hereby expressly disclaimed, or the extension beyond the duration of this limited warranty of any implied limited warranties, including
those of merchantability or fitness for an intended purpose. In some states orprovinces the exclusionor limitation of incidental or consequential
damages is not allowed, so those exclusions may not apply to you.
JA O Bathroom & Hardware Manufacturing Corp. provides the following warranties only to the first residential owner of our products.
FINISHES
JA O FAUCET LIFETIME FUNCTION AN FINISH LIMITE WARRANTY
COLD
2

109434 109434
Roman Tub Fillers
1SPOUT ASSEMBLY
2TEE AND HOSE ASSEMBLY
Insert SPOUT SHANK (1) through center hole of tub deck or mounting surface. Make sure RUBBER WASHER (2) is
properly positioned into SPOUT ESCUTCHEON BASE (3).
Assemble RUBBER WASHER (4), FIBER WASHER (5) and LOCKNUT (6) onto threads of SPOUT SHANK (1)
from underside of tub deck or mounting surface.
Push one RING WASHER (1) and one 0-RING (2) onto end
of SPOUT SHANK (3).
Slide the TEE (4) onto SPOUT SHANK (3) until it makes
contact with the 0-RING (2). Push the other 0-RING (2)
and RING WASHER (1) onto the SPOUT SHANK (3).
Make sure both 0-RINGS (2) are seated into grooves
of TEE (4).
Thread LOCK NUT (5) onto SHANK (3). Rotate TEE (4)
about 10 degrees from center and tighten securely.
Insert FIBER WASHERS (6) into COUPLING NUTS (7) of
SUPPLY HOSES (8) and tighten.
Align SPOUT (8) and tighten LOCKNUT (6).
Note: All deck mounted Roman tub sets must be installed with the tub spout outlet at least two (2) inches above
the flood level rim of the tub. See Figure 1a.
1
4
5
6
3
Turn off hot and cold water
supplies before beginning.
CAUTION
1-3/4" MAX.
2
8
2
2
1
5
6
6
1
3
4
GROOVE IN TEE
GROOVE IN TEE
10˚7
7
8
8
FRONT
Figure 1a
DECK MOUNT
BATH
RIM
BATH
RIM
TWO (2) INCHES
MINIMUM
TUB MOUNT
TWO (2) INCHES
MINIMUM
ROUGHING-IN
DIMENSIONS
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
TOOLS REQUIRED
Tubing Cutter Regular Screwdriver
Basin Wrench
3/4"NPT
INLETS
NOTE : BORE SIZE 1-3/8"
2-3/4" D.
1-3/8" D.
6-7/16"
9"
2-13/16" D.
30º
2" MAX.
3INSTALL VALVE BODIES AND HANDLES
INSTALL VALVES
REMOVE HANDLES
1-1/4'' MAX.
Thread LOCKNUT (10) to bottom of VALVE BODY (1). Make sure FIBER
WASHER (11) and RUBBER WASHER (12) are installed. Insert VALVE
BODY (1) through mounting hole from underside of SINK or mounting
surface.
Note: If HANDLES ASSEMBLIES are installed on VALVE BODIES (1) they must be
removed to install VALVE BODIES (1) from under lavatory or mounting surface.
To remove CRYSTAL KNOB HANDLE (2): Unthread INDEX CAP (3) and remove
HANDLE SCREW (4). Pull off CRYSTAL KNOB HANDLE (2) and unthread HANDLE
BASE (5). Unthread ESCUTCHEON (6).
To remove LEVER HANDLES (2): Loosen SET SCREW (7) with Hex Wrench
provided with faucet. Pull LEVER HANDLE (8, 9) off and unthread HANDLE BASE (5)
and ESCUTCHEON (6).
Insert FIBER WASHERS (13) into COUPLING NUTS (14) of SUPPLY HOSES (15) and
tighten making water tight connection. Important: Loop SUPPLY HOSES (15) as
shown so they do not kink.
3
4
2
5
6
10
1
13 14
15
11
18
16
12
JADO
INSTALL HANDLES
COLD
HOT
8
9
7
17
17
7
Hex wench
supplied
Seal
Note: VALVE BODY marked Hot is installed in the left Mtg. hole,
VALVE BODY marked Cold in the right when facing front of fitting.
Maximum mounting surface thickness is 1-1/4".
For Crystal handles: With VALVE in off position align CRYSTAL HANDLE (2) and install
onto VALVE STEM (18). Install HANDLE SCREW (4) and tighten. Install INDEX CAP (3).
For Lever Handles: Install FRICTION WASHER (17) onto base of LEVER HANDLE (8, 9).
With VALVE in off position align LEVER HANDLE (8, 9) as shown or as desired. Install
LEVER HANDLE (8, 9) onto VALVE STEM (18) and tighten SET SCREW (7) with HEX
WRENCH supplied.
Thread ESCUTCHEON (6) with seal onto VALVE BODY (1). Thread HANDLE
BASE (5) onto VALVE BODY (1) until snug against internal stop. Thread
ESCUTCHEON (6) counter-clockwise until seated against HANDLE BASE (5).
Set VALVE BODIES (1) so that their outlets are facing toward SPOUT TEE
(16) and then tighten LOCKNUT (10) using wrench.
6" TO 12"