JBL EON 515 User manual

JBL Incorporated, 8500 Balboa Boulevard, P.O. Box 2200, Northridge, California 91329 U.S.A.
JBL EON515/230 REV E
PACKAGE WIRING DIAGRAM
03-10
Technical Manual
JBL EON515/230
SPECIFICATIONS
ACOUSTIC & ELECTRICAL SPECIFICATIONS:
• System Power Rating: 450 W continuous, 900 W peak
• Frequency Response: 42 Hz – 18 kHz (± 3 dB) (EQ in “Flat”
position)
• Frequency Range: 39 Hz – 20kHz (-10 dB) (EQ in “Flat”
position)
• LF Power Amp: 350 W continuous at driver impedance
• HF Power Amp: 100 W continuous at driver inpedance
• Input Gain (input 3): Mic position: -Infinity to +40 dB
Line position: -Infinity to +4 dB (+20
dBu Max signal input)
• Input Gain (input 1 & 2): -Infinity to +4 dB (+20) dBu Max signal
input)
• Input Impedance: 64 K ohms (balanced) 32 K (unbal-
anced)
• Boost EQ: LF +3 dB Shelfing Filter @ 200 Hz
HF + 25 dB Shelfing Filter @ 4 kHz
• Low Cut Filter: Preset high pass @ 120 Hz
• Crossover Frequency: 2.2 kHz
SYSTEM COMPONENTS:
• Cabinet: (Not for Sale)
• Baffle/Grille Assembly: 441739-001
• Low Frequency 265F-1 380 mm (15 in) Different-
Transducer: ial Drive®integated woofer with dual
2” voice coils
SYSTEM COMPONENTS: (CONT’D)
• DC Resistance: 1.35 ohm ±10%
• High Frequency 2414H 25.4 mm (1 in ) neodymium
Transducer: compression driver
• DC Resistance: 3.60 ohm ± 0.2%
• Input 3 connector: Balanced XLR / 1/4 inch TRS combo
jack with XLR loop through
• Input 1 & 2 connectors: Balanced 1/4 inch TRS jack
• Output (Loop/Mix switch): Balanced male XLR, +20 dBu (peak)
o/p level in MIX position
• XLR Pin Assignments: Pin 2 (+), Pin 3 (-), Pin 1 (GRN)
AURAL SWEEP TEST SPECIFICATIONS:
A. System Aural Sweep Test: 1.0Vrms Input, 20 Hz to 2 kHz
Ch 1 input all and pots full clockwise
B. L.F. Aural Sweep Test: 3.5V Input,10 Hz to 300 Hz
C. H.F. Aural Sweep Test: .75V Input, 500 Hz to 1.5 kHz
PHYSICAL SPECIFICATIONS:
• Enclosure Dimensions: 685 x 435 x 366 mm D
(27.0 x 17.3 x 14.4 in D)
• Shipping Weight: 32.5 lbs. (14.8 kg)
WARRANTY INFORMATION:
• Refer to Warranty Statement packed with each product.
Amplifier Assembly
Wire Harness Assembly
364836-001
Driver, High Freq
2414H
(342423-002X)
(SEE SCHEMATIC PAGE)
Driver, Low Freq.
265F-1
(363837-001X)
Cone Repl
C2R265-1
BLU
GRN
BLU / BLK
GRN/BLK
Fillers (2)
364823-001
Bag
322591-001
19”x16”xc42” LG
.003 THKLDPE
CLEAR
Carton
364824-001
Cord, AC, Line
425-00000-00 120V
425-00000-01 230V
Warranty 59660
Owners Manual
364822-001
(Available on web-site
only)
-+-+

JBL EON515/230
JBL EON515/230
SCHEMATIC (Wire Harness)
364836-001

COMPONENT EXPLODEDVIEW JBL EON515/230
Screw
813-21300-10
M3 .5X 10MM
RND, PH, CLR,
ZINC LCS Rubber Foot (2)
364802-001
Fly Bolt (4)
364616-001
Nut (4)
838-00800-00
M14,REG,CLR ZINC,RH
Washer (4)
848-00100-02
M14,REG, CLR ZINC
Driver, Low Freq.
265F-1
(363837-001X)
Cone Repl
C2R265-1
Screw (8)
365626-001
M5 PTx25MM
FIL,PH,BLK,ZINC,
Thumbscrew
364983-001
Handle Pocket Assembly
365135-001
Screw (4)
365627-001
M4 X 25MM
FIL,PH,BLK, WASHER HD
Amp Board
444969-001
Input Module
442973-001
A/C Inlet PCB
365428-001
Interface PCB
138927-1_4JBL
Amplifier Gasket (2)
364821-001
Screw (12)
813-41300-15
M3 .5X 15MM
PAN,PH,CLR ZINC,LCS
Wire Harness
364836-001
Heat Sink
364674-001
Input Plate
364676-001
Logo, Heat Sink
364678-001
Cover Badge, Heat Sink
364679-001
Clip, MRX IGBT
138556-1JBL
Clip, EON 500 to -220
140323-1JBL
Silipad, EON515
140324-1JBL
Silipad, EON 500
140325-1JBL
Silipad, EON515 IGBT
138526-1JBL
Silipad, MRX
138525-1JBL
Enclosure Assembly
EON515 (Not Avail.)
Sound Dampener (3)
365625-001
Cover,Fly Bolt (2)
364805-001
Upper Handle
364654-001
Gasket,Enclosure
364835-001
Insert
365433-001
M6 x 12MM PPB TYPE
Driver,High Freq.
2414H
(342423-002X)
Screw (10)
365270-001
M4 x .65
Washer (10)
365156-001
Rubber
Screw (33)
862-41410-10
6 x 5/8
PAN,PH,HIGHLO,
BLK ZINC,LCS
Screw (4)
814-41300-06
M4 x 6MM
PAN,PHILLIPS CLEAR,
ZINC
Screw (2)
365435-001
M4 x 5MM
TREAD CUTTING
Amplifier
Sheild
365107-001
JBL EON515/230
Baffle/Grille
Assembly
441739-001
Logo Assembly
364804-001