JCM Technologies CAP T868 User manual

jcmtechnologies
CAPTIVE
RadioBand3G System
EN
CAP T868 / CAP T916
CAP ACTIVE
CAP R868 / CAP R916
CAP MAGIN
User manual
CAPTIVE SYSTEM
CAPTIVE FAMILY

CAPTIVE SYSTEM
jcmtechnologies
2
1. Introduction 4
1.1. General description 4
1.2. CAP T868 / 916 TRANSMITTER 6
1.3. CAP ACTIVE TRANSMITTER 6
1.4. CAP R868 / 916 RECEIVER 8
1.5. CAP MAGIN 9
2. Detection principles 11
3. Installation 11
3.1. CAP T / CAP R 11
3.2. CAP ACTIVE 14
3.3. CAP MAGIN 16
3.3.1. Fixing the grey magnet 15
3.3.2. Fixing the black magnet 16
4. Connections 17
4.1. Connecting the CAP T (safety edge) 17
4.2. Connecting the CAP ACTIVE (safety edge) 18

CAPTIVE SYSTEM
jcmtechnologies
3
4.3. Connecting the receiver to the control panel 19
4.4. Connecting MAGIN to the receiver 21
5. Adjustment of the reciver / Operating modes 22
6. Programming 24
6.1. Programming safety edge to receiver 24
7. Checking and maintenance 26
7.1. Does the equipment work properly 26
7.2. Check the correct operation 26
7.3. CHECK function 27
7.4. Troubleshooting 28
7.5. Total reset 29
7.6. Batteries / Replacing the CAP ACTIVE transmitter battery 30
8. Technical Data Summary 32
9. Maintenance register 33
10.Important safety instructions 34
11.Notes 35
12. EC Declaration of conformity 36

CAPTIVE SYSTEM
jcmtechnologies
4
1. Introduction
1.1. General description
Radio safety solution for industrial sliding gates with NO-TOUCH technology. Based on 3 devices: transmitter (CAP
T868/916, CAP ACTIVE 868), receiver (CAP R868/916) and inhibition detector (CAP MAGIN).
•Compatible with all kind of metallic / aluminum sliding gates.
•Category 2 devices.
Safety edge gives the device security degree. NO-TOUCH detection is a courtesy function.
NO-TOUCH detection is not working all the time, it only should work during the movement of the gate. It detects metal
or conductive objects near the safety edge. It cannot detect plastics, glass neither other no conductive materials.
The receiver manages the activation and deactivation of NO-TOUCH function depending on the status of the inhibition
detector (inhibition input).
Inhibition detector is based on magnetic fields thanks to the use of 2 polarized magnets (grey and black). These 2
magnets are the responsible for activating and deactivating NO-TOUCH sensor on the transmitter. It is needed to
deactivate NO-TOUCH sensor at a distance of 30-50cm before the door is totally closed (inhibition zone).
CAP system is not suitable
for wood gates neither
other non conductive
materials.

CAPTIVE SYSTEM
jcmtechnologies
5
The system complies with EN ISO 13849-1:2008, category 2, PLd. (when the auto-test function is used.)

CAPTIVE SYSTEM
jcmtechnologies
6
1.2. CAP T868/916 TRANSMITTER
–
Recomended
sensibility range
adjustment
between 5-6

CAPTIVE SYSTEM
jcmtechnologies
7
1.3. CAP ACTIVE TRANSMITTER
Recommended
sensibility range
adjustment
between 6-7

CAPTIVE SYSTEM
jcmtechnologies
8
1.4. CAP R868/916 RECEIVER

CAPTIVE SYSTEM
jcmtechnologies
9
INH.
GND.
9 Vdc
1.5. CAP MAGIN
CAP MAGIN
DETECTOR
NO TOUCH activated
NO TOUCH inhibited
2m
GREY
MAGNETS
BLACK
GREY - BLACK magnets position
depends on the direction of the
gate. CAP MAGIN LED must be
GREEN while gate is closing.
RED when gate is stopped.

CAPTIVE SYSTEM
jcmtechnologies
10
2. Detection principles
CAPT detects objects near the safety edge of the gate by detecting variations between conductive part of the gate and
conductive parts of the safety edge.
For that reason CAPT has a cable to connect GND to the metal part of the gate.
It is very important for the proper working of the NO TOUCH detection that the ground
reference is properly connected.
The measurement is going to
depend on:
•Size of the conductive
part of the object.
•Distance from the
object to the edge of
the gate.
Maximum safety edge length=
2.5m.

CAPTIVE SYSTEM
jcmtechnologies
11
3. Installation
3.1. CAP T/CAP R
IMPORTANT
Do not place
metal surfaces
between
transmitter and
receiver.

CAPTIVE SYSTEM
jcmtechnologies
12
Avoid vibrations is a MUST.
Use safety edges where conductor cannot be moved easily by the movement of the door.
Use metallic profiles appropriated for the safety edge used.
–
IMPORTANT
To avoid false detections and ensure a
longer NO TOUCH range, the gap
between the “internal wires” and the
gate must be as bigger as possible.
GROUND cable must be
connected to the metallic part
of the gate.
Safety edge wire
must be as shorter
as possible
avoiding
ib ti

CAPTIVE SYSTEM
jcmtechnologies
13
3.2. CAP ACTIVE
Ground cable must be
fixed to the gate.
Make sure that ground
and antenna wires are
NOT in contact.

CAPTIVE SYSTEM
jcmtechnologies
14
1-2 cm
Grey magnet
Green colour
on drawings
Red colour
on drawings
Black magnet
Red colour on
drawings
3.3. CAP MAGIN
MAGNETS:at the gate.
Grey magnet should be installed to activate the NO-TOUCH sensor when the gate
starts the close movement. Black magnet switches off the NO-TOUCH sensor in
order to allow the gate to closing.
GREY – BLACK magnets position depends on the direction of the gate. CAP MAGIN LED must be GREEN while gate is
closing/opening, RED when gate is totally closed/opened.
CAP MAGIN: install onto a support near the magnets and at the same height.
GATE
SUPPORT
MAGNET
MAGIN
In case the gate is not totally
opened/closed, a safety time of
5 minutes is added to avoid
battery consumption.
Maximum NO TOUCH
activation time = 5 minutes
Depending on the gate direction, BLACK magnet is the one
who actives the NO-TOUCH sensor.

CAPTIVE SYSTEM
jcmtechnologies
15
3.3.1. Fixing the ACTIVATION magnet
With the GATE TOTALLY OPENED fix the south field magnet (grey).
Grey magnet must be 2-3 cm away from the MAGIN detector. When the door starts closing, the green magnet travels
past the MAGIN and NO-TOUCH gate sensor is activated.
LED indicator on MAGIN detector changes to green color when grey magnet passes in front of MAGIN.
MAGIN
Gate must be
TOTALLY OPENED to
fix the grey magnet.
CAP T
INHIBITION ZONE: NO TOUCH
30-50 CM
Before fixing the magnet, CAP ACTIVE/CAP T must be programmed at the
i

CAPTIVE SYSTEM
jcmtechnologies
16
3.3.2. Fixing the DEACTIVATION magnet
With the GATE AT 30-50CM FROM ITS CLOSED POSITION:
Black magnet must be fixed at the other extreme of the gate (in respect of the grey magnet). The location of this magnet
depends on the inhibition zone desired.
Due to NO TOUCH detection, it is required that an inhibition zone is created at the end of the gate movement in order to
avoid the detection of the wall support by NO TOUCH detector. In this zone, the safety edge will only be activated from
mechanical compression.
Inhibition zone length depends on NO TOUCH sensitivity adjustment.
When NO-TOUCH sensor is detecting, an LED on the transmitter is activated. If indicators on the transmitter are
switched off, it is needed to push PROG button on the transmitter to activate during 5 minutes the LED visualization on
the transmitter.
LED indicator on MAGIN detector changes to red color when black magnet passes in front of MAGIN.
Before fixing the black magnet, CAP ACTIVE/CAP T must be programmed at the
receiver
The location of the black magnet indicates the inhibition zone at
closing.

CAPTIVE SYSTEM
jcmtechnologies
17
4. Connections
4.1. Connecting the CAP T (safety edge)
Ground cable must be fixed to the
gate.
Make sure that ground and antenna

CAPTIVE SYSTEM
jcmtechnologies
18
4.2. Connecting the CAP ACTIVE (safety edge)
Check the ground wire is properly fixed and the cable tension is calibrated.

CAPTIVE SYSTEM
jcmtechnologies
19
4.3. Connecting the receiver to the control panel
Connecting the safety outputs to control panel:
Example: connection to control panel with safety contact / STOP input
Example: connection to control panel with input for safety
edge 8k2
The equipment can be connected to the control panel with
input for safety edge 8k2 or directly into a safety input
normally closed contact as if it were a photocell or stop
signal.
This connectivity exists for R1 and R2 outputs.

CAPTIVE SYSTEM
jcmtechnologies
20
In order to comply with EN ISO 13849-1: 2008 safety standard, a signal to test the system must be connected.
When working with optical safety edges, in ON mode, only OSE-S7502 are allowed as they are kept always active. The
radio communication is tested every 7 or 30 seconds depending on the selector SW1 of the receiver.