JCM EBA-30-SD3 User manual

Issue 01/2006
Contents
Product Name & Specifications
1. Product Name
2. Precautions
3. Features
4. ComponentNames
5.GeneralSpecifications
6.RetrievingBills
7.Cabling
8.OutsideDimensions
9. Country Codes
Bill Acceptor
EBA-30/31-SD3(EBA-30/31)
EBA-32/33-SD3(EBA-32/33)
EBA-34/35-SD3(EBA-34/35)
CHAPTER 1
Copyright © 1998 Japan Cash Machine Co.Ltd. All rights reserved.

1 - 2
CHAPTER 1 Product Name & Product Specifications
EBA product name constitutes two kinds; [MODEL] name and [TYPE] .
As for (1) to (6), refer to the description of the optional items.
[MODEL] EBA - 3 * - SD3 ( EBA - 3 * )
(1) (1)
[TYPE] *** - * * * * - **
(2) (3) (4) (5) (6) (7)
JCM provides optional items for this model. Please consult JCM sales representatives for details.
(1) Type of CPU board
Two types of CPU boards (Flash-ROM or EP-ROM) are available.
0: DC12V Flash-ROM type board for ID-003/MDB interface (Standard)
1: DC12V EP-ROM typeboardfor ID-003/MDBinterface
2: DC12V Flash-ROM type board for ID-003/ccTalk/HII Interface (Standard)
3: DC12V EP-ROM type board for ID-003/ccTalk/HII Interface
4: DC12V/DC24V Flash-ROM type board for ID-003/MDB interface (Standard)
5: DC12V/DC24VEP-ROMtypeboardID-003/MDBinterface
(2) The country code corresponding to acceptable banknotes: 3-digit code under ISO3166 shall be
used. Refer to the country codes on page 1-11.
(3) Cash Box type
0: Without box (stackerless model)
4: 400-note capacity (Standard)
6: 600-note capacity (To be developed)
(4) Faceplate
0: Without faceplate (Standard)
1: With faceplate
(5) I/F conversion board
0: Without I/F conversion board (Standard)
1: With Type A I/F conversion board (For serial-to-parallel conversion. To be developed)
(6) Key Switch
0: Without Key Switch (Standard)
1: With Key Switch
2: With Key Switch (for UserA)
(7) Interface protocol ID
03: ID-003 JCMserialinterface
D3: ID-0D3 MDB interface
E3: ID-0E3 ccTalk interface (Note 1)
F3: ID-0F3 HII interface (Note 2)
**: Others The last two digits of interface ID are assigned.
Example: EBA-30-SD3-CZE-4000-03
EBA-30 model bill acceptor with standard SD3 stacker box, Czech software,
no faceplate, no I/D conversion board, no key switch, ID-003 I/F.
Note 1) "ccTalk" is a serial communication protocol provided by Money Controls.
Note 2) "HII" is a serial communication protocol provided by Mars Electronics International.
1. Product Name (Model Name + Type)

1 - 3
CHAPTER 1 Product Name & Specifications
2. Precautions
(1) Do not insert a torn,
folded, or wet bill, as this
may cause bill jam inside
the unit.
(2) Do not expose the unit to
water.
The unit contains several
precision electronic devices
which can be damaged if
water or any liquid is
sprayed or spilled into the
unit.
(3) Do not install the unit in a
dusty environment. Dust
may affect the sensor
performance.

1 - 4
CHAPTER 1 Product Name & Product Specifications
EBA-3X-SD3 provides the following features:
3-1 Automatic centering
Automatic centering mechanism allows the unit to read bills ranging from 62mm to 85mm without
using bill guides (side blocks). Bill acceptance rate and security against counterfeits have been
greatly improved.
3-2 Automatic Re-validation
The EBA-3x series features automatic re-validation. The unit attempts to accept bill three times in
total, if the bill is rejected in the first insertion.
3-3 Dip switch settings to accept/reject bills
Accept/reject of each denomination is DIP switch selectable.
3-4 Easy bill retrieval
The stacker box can be detached from the stacker unit to withdraw deposited bills.
3. Features
The standard SD3 stacker box stores up to 400 bills.
The stacker box is equipped with a coin lock for higher security.

1 - 5
CHAPTER 1 Product Name & Specifications
4. Component Names
    
  
 
 
 
I/F Connector
External
Display Connector

1 - 6
CHAPTER 1 Product Name & Product Specifications
5. General Specifications
5-1 Size of Banknotes Width: 62 to 85 mm, Length: 120 to 160 mm
5-2 No. of Denominations Up to 32 denominations
[Refer to "Data Setting Specifications" of each software]
5-3 Directions 4 ways (Longitudinal insertion)
(The directions may vary depending on the software specifications.)
[Refer to "Data Setting Specifications" of each software]
5-4 Acceptance Rate 95% or more (Including bills accepted in two retries. The following
bill is excluded:)
(1) Bill with stain, wear, wetness, tear or remarkable wrinkles
(2) Bill with folded corner or edge
(3) Bill with incorrect cut dimensions or improper alignment in printing
5-5 Processing Speed Approx. 2 seconds for validation. Approx. 5 seconds for stacking (with
SD3 stacker)
For a head unit without SD3 stacker, it takes approx. 3 seconds from
acceptance to ejection.
5-6 Interface (1) TTL serial interface
(2) MDB interface
(3) ccTalk / HII interface
(4) Parallel interface
Should be connected to an optional I/F conversion board.
5-7 Stacker Box (1) Capacity Approx. 400 bills
(2) Access Front Access
5-8 Escrow 1 Bill
5-9 Indication (1) The validator operating status is indicated by three LEDs (green,
red and orange) on CPU board.
Green LED: This LED lights during idling and bill-accepting
operation. When a bill is rejected, the LED blinks to
indicate the rejecting status (see Chapter 6, 6-11/12).
RedLED: This LED blinks when an error is detected.
The error status is indicated by the number of blinks
(see Chapter 6, 6-11).
OrangeLED: This LED lights when the guides of bill centering
mechanism are at the home position. While the LED is
on, the head unit can be opened.
(2) External display output (7-pin connector)
When this connector is connected to the optional display unit, the
acceptor’s operating status is displayed.
ON: The unit is able to accept bills.
OFF: The unit is unable to accept bills.

1 - 7
CHAPTER 1 Product Name & Specifications
5-10 Power Supply Voltage 12VDC±5%(EBA-30/31/32/33/34/35)
(Use a power supply with 3Aor higher capacity.)
24VDC±10%(EBA-34/35)
(Use a power supply with 1.6Aor higher capacity.)
5-11 Current Consumption 12VDC
(1) In standby: 0.3A
(2) During operation:1.6A(3Amax.)
24VDC
(1) In standby: 0.2A
(2)Duringoperation:0.9A (1.6A max.)
5-12 Operating Environment (1) Operating temperature: 5 to 50ﾟC
(2) Storing temperature: -20 to 60ﾟC
(3) Relative humidity: 30 to 85% (no condensation)
(4) Installation: Install the unit indoors where it is not exposed to direct
sunlight.
5-13 Outer Dimensions Refer to the outline drawings for the configuration with SD3 stacker,
and without the stacker.
5-14 Weight (1) With SD3 stacker Approx. 2.5 kg
(2) Without SD3 stacker Approx. 1.0 kg
5-15 Mounting Horizontal mounting
Earthe the the sheet metal part of the unit
[NOTE] Unless otherwise specified, the general specifications of the EBA-3x series are measured
based on the following conditions:
(1) Power supply voltage: 12 VDC ± 0.1 V (19.9 to 12.1 V)
24VDC ± 0.2 V (23.8 to 24.2V)
(2) Temperature: 25
ﾟ C ± 3 ﾟ C (22 to 28 ﾟ C)
(3) Relative humidity 40 to 65%
(4) Standard bill 20 Euro bill

1 - 8
CHAPTER 1 Product Name & Product Specifications
6. Retrieving Bills
(1) Unlock the stacker box and pull it out
from the stacker unit.
(2) Retrieve the bills.

1 - 9
CHAPTER 1 Product Name & Specifications
7. Cabling
Mating connector
Housing
ZHR-7(JST)
Contact
SZH-002T-P0.5
Recommended wire
AWG26~28 UL1061
Acceptor's connector
Box type plug
XG4C-1634(OMRON)
Mating connector
Contact
MIL type socket
XG4M-1630-T(OMRON)
Recommended wire
27mm pitch flat cable
AWG28 UL2651
Contact
XG5M-1635-N(OMRON)
Recommended wire
AWG26~28 UL1007
Acceptor's connector
Pin header
S7B-ZR(JST)

1 - 10
CHAPTER 1 Product Name & Product Specifications
8. Outside Dimensions
8-1 EBA-3x-SD3withoutfaceplate