Jenn-Air JXT7036ADS User manual

RANGE HOOD
USER
GUIDE
Model Number: JXT7036ADS
Manufacturer Number: MK8200
Size: 34”
TABLE OF CONTENTS
Safety Instructions....................................................1
Controls & Features................................................. 2
Maintenance.........................................................3-5
Warranty.................................................................. 6
Form No. A/04/03 Part No. UMK8200-0303A ©2003 Maytag Appliances Sales Co. Litho U.S.A.

USE AND CARE GUIDE
Read all Instructions before Installing and operating this appliance
MODEL: JXT7036ADS
Installation
The installation in this manual is intended for qualified installers,service technicians or persons
with similar qualified background.DO NOT attempt to install this appliance yourself.Injury could
result from installing the unit due to lack of appropriate electrical and technical background.
All electrical wiring must be properly installed, insulated and grounded. Overly accumulated
grease in old duct work should be cleaned out or duct work should be replaced if necessary to
avoid the possibility of a grease fire. Check all joints on duct work to insure proper connection
and all joints should be properly taped.
Operations
Read all instructions in this manual before operating the appliance. Save these instructions for
future reference.
Always leave safety grills and filters in place. Without these components, operating blowers
could catch on to hair, fingers and loose clothing.
NEVER dispose cigarette ashes, ignitable substances, or any foreign objects into blowers.
NEVER leave cooking unattended.When frying,oil in the pan can easily overheat and catch fire.
The risk of self combustion is higher when the oil has been used several times.
Cleaning
The saturation of greasy residue in the blower and filters may cause increased flammability.
Keep unit clean and free of grease and residue build-up at all times to prevent possible fires.
Filters must be cleaned periodically and kept free from accumulation of cooking residue (see
cleaning instructions inside).Old and worn filters must be replaced immediately.Do not operate
blowers when filters are removed.Never disassemble parts to clean without proper instructions.
Disassembly is recommended to be performed by qualified personnel only. Call our service cen-
ter for removal instructions. 1-800-JENNAIR (1800-536-6247) USA and CANADA
The manufacturer declines all responsibility in the event of failure to observe the instruc-
tions given here for installation,maintenance and suitable use of the product. The manufac-
turer further declines all responsibility for injury due to negligence and the warranty of the
unit automatically expires due to improper maintenance.
IMPORTANT SAFETY NOTICE
* Please check for latest specification revisions before any custom work or cutouts.
WARNING

CONTROLS & FEATURES 2
CONTROLS & FEATURES
Speed Selection
1
Lights On/Off
2
Lights On/Off
Speed Selection 2
1
This switch controls the speed of the blower. The first position is low speed, the second is
medium speed, and the third is high speed.
Turn lights on or off by moving this switch.

MAINTENANCE 3
CLEANING
Surface Maintenance:
Clean periodically with hot soapy water and clean cotton cloth.Do not use corrosive or abrasive
detergent, or steel wool/scouring pads which will scratch and damage surface.
For heavier soil use liquid degreasing cleaner.
After cleaning,you may use non abrasive stainless steel polish/cleaners,to polish and buff out the
stainless luster and grain.Always scrub lightly, with clean cotton cloth,and with the grain. Do not
use any product containing chlorine bleach. Do not use “orange” cleaners.
Residue Cups:
Residue and grease from cooking will collect in the residue cups located inside the range hood,
behind the perforated diffuser panels. Periodically, unscrew the inlet panels and remove the residue
cups for cleaning.Clean by hand or in a dishwasher. Spray degreasing detergent and leave to soak if
heavily soiled.
Dry residue cups and re-install before using hood.
Slide off to remove
residue cups

CLEANING AND MAINTENANCE 4
SELF CLEAN FEATURE
set to lowest speed:
Using Self Cleaning:
Model JXT7036ADS hoods are designed with a self cleaning feature.The centrifugal blower system
automatically liquefies cooking residue accumulated in its internal housing, and deposits the residue
in the cleaning cup.Nevertheless, grease from cooking can also dry and adhere in the internal hous-
ing. Running the self clean function periodically will flush out accumulated residue in the range
hood’s internal housing.
Cleaning Frequency:
Cleaning should be completed approximately once a month under normal use.
Detergent:
Non-corrosive, non-abrasive grease cutting spray detergents are recommended.
Self Clean:
Turn blower on lowest speed for cleaning.
With nozzle on ‘spray’, squirt the grease cutting
detergent through the safety grill, directly onto the
blower blades 10-15 times.
Allow self cleaning to complete for 10 minutes,
turn blowers off.
Remove cleaning cup.Clean w/ mild detergent
or in dishwasher under normal wash cycle.
(If desired, repeat above steps with water
to rinse out detergent)
WARNING: Use only non-corrosive & non-abrasive
grease cutting detergents.
DO NOT USE OVEN CLEANERS.