Jessberger JP-05 User manual

Operating Instructions
Stainless Steel Barrel Hand-Pump JP-05
Safety Regulations
Observe all warnings and safety regulations.
When filling flammable liquids, be sure to comply with the “Technical
Regulations for Flammable Liquids” and safety tips from the reagent
manufacturer (safety specifications sheet).
When filling dangerous liquids, you absolutely must wear protective
clothing (protective glasses, gloves, apron and possibly boots).
Every user must know the contents of these operating instructions and
have them handy at all times.
Use the equipment within the framework of the material stability. The
pump is made of V4A steel, material 1.4571 (SS 316Ti) and PTFE.
Only fill media emitting gases and smoking media in well ventilated
areas. Also refer to the safety tips from the reagent manufacturer (safety
specifications sheet).
Only use the equipment in such a way that neither the operator nor other
persons are endangered.
Never use force when operating the equipment.
Important: When filling slightly flammable liquids take precautions for
removing electrostatic charges. Use the Anti-static set (Our Art.No. 9003). Pls
see page 3.
Packaging/Contents
Please check the contents to make sure everything is included and for possible
transport damages. Point out any external, obvious damages on the packaging to
the deliver/shipper and have him confirm them in writing.
The pump consists of different pieces:
1. Hand pump with male thread 5/4” at discharge connection.
2. Discharge arc or hose connection and if necessary bonding ground set.
JESSBERGER GmbH - Jaegerweg 5 - D-85521 Ottobrunn
Tel. +49 (0) 89 - 66 66 33 400 - Fax: +49 (0) 89 - 66 66 33 411
[email protected] - www.jesspumpen.de
Stand: 01.10.2013

- Page 2 -
Operation, Precautionary Measures, Application Limitations
These pumps serve to fill highly fluid to oily liquids from canisters and barrels
up to approx. 220 liters. The stainless steel model in connection with the anti-
static set is suitable for filling flammable liquids. Use the PP polypropylene
model for acids and caustic solutions.
Always hold containers to be filled away from your body and wear protective
clothing. Do not extend the discharge tube with a hose.
Make sure that the discharge arc is fastened tightly to the pump.
The user has to check whether the equipment is appropriate for his
application.
Parts Coming into Contact with Media
Stainless steel, material 1.4571 (316Ti) and gaskets made of PTFE.
Cleaning and Maintenance
Make sure that no coarse dirt particles are in the liquids. Dirt can destroy the
pump valves and guides.
Rinse the pump using appropriate media at regular intervals.
Warning: Avoid injuries due to dangerous fluids! Equipment parts might be
filled with reagents. Never direct openings at a person’s body!
Wear protective goggles, gloves and apron!
Malfunctions –What can I do?
Liquid is not filled:
- Bottom valve is soiled.
If only a little liquid remains in the container, you must pump correspondingly
longer.
JESSBERGER GmbH - Jaegerweg 5 - D-85521 Ottobrunn
Tel. +49 (0) 89 - 66 66 33 400 - Fax: +49 (0) 89 - 66 66 33 411
[email protected] - www.jesspumpen.de

- Page 3 -
TRANSFERRING OF FLAMMABLES OR USE IN HAZARDOUS DUTY
ENVIROMENTS
Bonding is an electrical connection between a primary metal vessel
and a metal receiving vessel. See Schematic.
Grounding is an electrical connection between a metal vessel, pump,
motor and a constant ground; i.e. a metal rod driven into the earth.
Bonding and grounding are
required when pumping
flammable materials or in
hazardous duty enviroments.
Failure to bond and ground
properly can cause a discharge
of static electricity resulting in
fire, injury or death. Please
always take care of the official
safety authority regulation. If
in doubt, do not start pump!
Be sure bonding and
grounding wires are secure
before starting operation.
(Ground and bond wires must
have less than one ohm
resistance for safe usage.
Check continuity before
starting.) Always check with a
safety engineer when any
question arises and
periodically check safety
procedures with a safety
engineer.
JESSBERGER GmbH - Jaegerweg 5 - D-85521 Ottobrunn
Tel. +49 (0) 89 - 66 66 33 400 - Fax: +49 (0) 89 - 66 66 33 411
[email protected] - www.jesspumpen.de