Jeti usa Duplex ds-6 User manual

1121.4 Main Function Interface1.5 LED Displaying Board Function1.6 Menu

2.7 Timer Set

13151617171818191920202121222223242425

DS-6

1.1 Transmitter Chart

454.0V.VoltageModel Memory

4.8V MOD6

SYS.

TIMER

FUN.

FunctionSystem Timer

F100

4.0

F100

4.8V MOD6

SYS.

TIMER

FUN.

F100

12. 2.4GHz Binding

13. Basic Features

14. Main function Interface

15. LED Display Board

Make sure that the transmitter is on the correct model and powered off. Place

binding plug in the EXT port on the receiver and power up receiver.

Turn on the transmitter and when it binds, remove the binding plug from the

receiver. Model is now bound.

1. The Binding Process

TIMER

SET

4.8V MOD6

TIMER

FUN.

F100

SYS.

1.6 MENU2.1 System menu introductionMODEL SET(Page8～9)PLANE TYPE(Page10)

892.2 MODEL SET

1011.1)Press“down”to select “SYS MENU”,and press“ENTER”to come to the interface.2)Press“up”or“down”to select “NORMAL”or“TRAINER”.

TIMER

SET

TIMER

SET

TRAINER

2.3 PLANE TYPE2.4 STICK MODE2.5 STICK ADJ2.6 TRAINER

1213

4.8V MOD6

SYS.

TIMER

FUN.

2.7 TIMER SETChoose Timer set Operation 1. Press Down to select Sys Menu, and press Enter to the interface2. Down button select Timer SET3. Up and Down button setting time M:S4. Entering setting Timer Press INC or DEC choosing increase and decrease5. Return main Interface. INC -- TIMER START DEC -- TIMER RESETCaution:This setting before and after 20seconds each two seconds Alarm. after Alarming each 10 seconds. then Alarm not stop.Press DEC --- TIMER RESET LOGOUT TIME RENEW TIMER

3.1 Functions. Menu Introduction (Heli)

DR(Page 14)SUB TRIM(Page 16)TRAVEL(Page 17)TRAVEL(Page 17)

1415

SUB.TRIM

A/E/R D/RA/E/R D/R3.2 D/RSWASH MIX(Page 18)GYRO.SENS(Page 18)THRO.CURV(Page 19)MONITOR(Page 19)PIT.CURV(Page 20)THRO.HOLD(Page 20)

1617

A/E/R D/R3.3 SUB TRIM3.4 TRAVEL3.5 CH.REV

1819

Monitor systemOperation:1)Press“up”to select “FUN MENU”,and press“ENTER”to come to the interface.2)Press“up”or“down”to select “MONITOR”,and now the shadow area is the item that can be set currently.Press“ENTER”to go to the next step.3)When you move the sticks or channel switches,you can find the corresponding channel bars will change accordingly.This function is designed to monitor the working conditions of the transmitter.4)After your setting,press “EXIT”to save the setting and leave the operation.Remark:this function helps you adjust the setting,neutral trim as well as channel inspection. Throttle curve operationOperation:1)Press“up”to select “FUN MENU”,and press“ENTER”to come to the interface.2)Press“up”or“down”to select “THRO CURV”,and now the shadow area is the item that can be set currently.Press“ENTER”to go to the next step.3)Press“ENTER” to select the throttle curve point.There are 5 points,they are L,1,2,3,H.Press“INC”or“DEC”to set the corresponding value separately,and the throttle curve will change accordingly. 4)There are three throttle curves to be selected,normal,“IDLE 0”and“IDLE 1”by the switch at the left top of the transmitter.. 5)After your setting,press“EXIT”to save the setting and leave the operation.Remark:the transmitter can save 3 groups of different throttle curves.When you make 3D fly, please ask for instruction from experienced pilots.3.6 SWASH.MIX3.7 GYRO.SENS3.8 THRO CURV3.9 MONITOR