Jetta Baths Troubleshooting guide

www.jettacorp.com
Owner’s Manual &
Installation Guide
This manual is to be given to the product owner and should be kept for future use.

© 2013 Jetta Corporation. All rights reserved. REV 05/2013
800-288-7771
2
Table of Contents
FACTS THAT MAKE JETTA YOUR BEST CHOICE.......................................4
SAFETY INSTRUCTIONS ....................................................................................5
INSTALLATION INSTRUCTIONS....................................................................6
INSTALLATION INSTRUCTIONS - optional skirt ................................7
MAINTENANCE & CLEANING.........................................................................8
OPERATING INSTRUCTIONS - CLASSIC SERIES ......................................9
OPERATING INSTRUCTIONS - DESIGNER/ELITE SERIES ....................10
OPERATING INSTRUCTIONS - OPTIONAL AIR BATH ...........................11
TROUBLESHOOTING..........................................................................................13
LIMITED FACTORY WARRANTY.....................................................................14

3
© 2013 Jetta Corporation. All rights reserved. REV 05/2013
www.jettacorp.com
Lean back and escape into the warmth of your new Jetta bath with the
condence that you have made the right choice.
Jetta whirlpool baths have unique features that are not found in any
other whirlpool bath. We have mastered the ergonomics of body comfort and
perfect jet placement, giving you luxury at a reasonable price. Our
passive warm air induction systems and totally insulated whirlpools allow us to
provide our exclusive Jetta Stay Hot Guarantee. We guarantee the water
temperature will stay within 2 degrees of its original temperature after 30 minutes
of use. This insulation also means that distractive motor noises and vibrations are
virtually eliminated, allowing you to escape from the world a little bit longer.
In this manual, you will nd the information that you will need to install and
operate your new bath. If you have any additional questions regarding your
tub, feel free to call us at 1-800-288-7771, and we’ll be happy to answer your
questions.
Thank you for choosing Jetta.
Date Purchased: __________________________________________
Purchased From: __________________________________________
Serial #: ________________________________________________
Model #: ________________________________________________
Manufacturer’s Date: _______________________________________
Installed By: _____________________________________________

© 2013 Jetta Corporation. All rights reserved. REV 05/2013
800-288-7771
4
owner’s manual
facts that make jetta your best choice
Jetta Bath Systems are available in a wide variety of shapes, sizes, and jet congurations with several premium •
models available and offers the ultimate in hydrotherapy and relaxation. Jetta has mastered the ergonomics
of body comfort and jet placement and includes built in arm, foot and head rests as well as lumbar support for
maximum comfort.
Made with the highest quality materials and manufactured to ANSI and ASME standards, Jetta offers quality•
and luxury at an affordable price. Features such as rebar, extra thick acrylic, low density insulating foam
surrounding each tub and a permanent color throughout the entire bath set Jetta apart. Each bath is
manufactured with a high gloss, high impact non-porous acrylic, which casts permanent color throughout and
is chemical, stain and UV resistant. Due to the high heat retention of this material, the acrylic is warm to the
touch, providing a more comfortable bathing experience and will maintain a beautiful appearance for years.
Unlike most bath tubs, our insulated whirlpool baths are engineered to stay hot without the use of an in-line•
heater. In fact, we are so condent in our insulation and warm air induction system, we guarantee that the
water will stay within 2 degrees of its original temperature after 30 minutes of use. The insulation surround-
ing each tub also protects the plumbing, gives added support and cuts down on noise and vibrations. The fact
that there is no hazardous heating element in contact with the bath water is also an important safety feature,
which will save you on costly wiring, operating costs, and repair bills when the heater inevitably fails.
Jetta baths are tted with full size ow-adjustable rotating and directional jets. Elite and Designer baths have •
rotating back jets that are also adjustable to stationary jets. All body jets and Classic back jets are direction
adjustable at the jet to allow focused water ow. Each full size jet is volume adjustable for a truly customized
hydro-massage.
Our air option can be added to most whirlpool baths to create the ultimate bathing experience for an•
air/whirlpool combination. The air option may also be added to most non-skirted soaker baths to provide
a gentle relaxing massage.
The passive warm air induction system is another unique feature of Jetta baths. This efcient system quietly •
recirculates heated air from the motor back to the bath water through the jets. This very efcient system
combined with the low density polyurethane foam insulation eliminates the need for an in-line heater.
Jetta whirlpools are plumbed with antimicrobial ex pipe. This antimicrobial piping is held in place by our•
insulation, uses gravity ow draining and will not hold water. Along with our 100% self draining suction
tting (IAPMO listed), this makes for a cleaner, healthier bath.
The Trissage Control offering distinct pump ow rates is standard on Designer and Elite Series and optional •
on the Classic Series. This control offers the same benet as a multi-speed pump, but eliminates the need for
expensive two and three speed pumps.
Jetta baths are extra deep - each tub is at least 20” deep, but can go to 32”, they are available in non-jetted,•
“soaker” models and several styles are also available with integral skirts with access panels.
Jetta baths are available in standard colors of White, Bone and Biscuit. A wide variety of Kohler, American•
Standard and other decorator colors are available. Each tub can be trimmed with matching acrylic or can be
upgraded to a Chrome, Polished Brass, Oil Rubbed Bronze or Satin Nickel trim kit.
Jetta baths are U.L. Listed as hydro-massage baths. Jetta baths are commercial quality and designed to reduce•
utility costs, noise complaints and service calls. Each Jetta J-Line and WaterDance Baths by Jetta bath comes
with a 10-year limited factory warranty.
Jetta baths are available with many options including contoured and jetted neck pillows, Mood or LED lights,•
waste and overow systems, aromatherapy, and 6” acrylic grab bars to customize your Jetta experience.

5
© 2013 Jetta Corporation. All rights reserved. REV 05/2013
www.jettacorp.com
owner’s manual
safety instructions
IMPORTANT: READ AND FOLLOW ALL INSTRUCTIONS PRIOR TO INSTALLATION
AND USE. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Operational:
Do not permit children to use unit unless they are closely supervised at all time. Supervision is also required when1.
the bath is used by an elderly or handicapped individual.
Use this unit only for its intended use as described in this manual. Only use attachments recommended by the manufacturer.2.
Do not insert any object into any opening. Do not operate electrical appliances while in or within 5 feet of the bath.3.
Do not operate this unit without the guard over the suction tting. Long hair must be kept away from the suction 4.
screen to avoid entrapment. If entrapment occurs, immediately turn unit off.
Do not start pump before unit is lled with water 2” above jets – this will void the warranty.5.
Water level should not exceed the lowest edge of the overow or controls. 6.
The water in a whirlpool should not exceed 40°C (104°F). Water temperatures between 38°C (100°F) and 40°C 7.
(104°F) are typically considered safe for a healthy adult. Prolonged immersions in hot water may produce hyper-
thermia. The symptoms of hyperthermia include an increase in the internal temperature of the body, dizziness,
lethargy, drowsiness and fainting, which can be fatal. Lower temperatures are recommended for extended use
(exceeding 10-15 minutes) for young children.
Exposure to very hot water has the potential to cause fetal damage during the early months of pregnancy. Preg-8.
nant, or possibly pregnant women should limit water temperature to 38°C (100°F). Consult a
physician before using.
Persons using medication should consult a physician before using a whirlpool since medication may induce drowsi-9.
ness, affect heart rate, blood pressure and circulation. The use of alcohol, drugs or medication before or during
whirlpool use may lead to unconsciousness with the possibility of drowning.
Persons suffering from obesity or with a medical history of heart disease, low or high blood pressure, circulatory10.
system problems, or diabetes should consult a physician before using a whirlpool.
Electrical:
This unit must be connected to a supply circuit that is protected by a ground-fault-circuit-interrupter (GFCI). Such 1.
a GFCI should be provided by the installer and should be tested on a routine basis. To test the GFCI, push the
test button. The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to
operate in this manner, there is a ground current owing indicating the possibility of an electric shock. Do not use
this unit. Disconnect the unit and have the problem corrected by a qualied service representative before using.
Disconnect power before servicing.2.
Whirlpool Pump Connections Only:3.
a. A green colored terminal (or wire connector marked “G”, “GR”, “Ground” or “Grounding”) is provided within the
terminal compartment. To reduce the risk of electric shock, connect this terminal or connector to the grounding ter-
minal of your electric service or supply panel with a continuous green insulated copper wire equivalent in size to the
circuit conductors supplying this equipment.
b. A pressure ground connector is provided on the exterior of the terminal box within this unit to permit connection
of a No. 8 AWG (8.4mm²) solid copper bonding conductor between this unit and all other electrical equipment and
exposed metal in the vicinity, as needed to comply with state and local requirements.
For whirlpools and soakers the Mood or LED light option has its own separate power cord and must be plugged in.4.
Install to permit access for servicing (for built-in and custom units).5.
Installer / Owner bears all responsibility to comply with all state and local codes when installing this product.6.

© 2013 Jetta Corporation. All rights reserved. REV 05/2013
800-288-7771
6
owner’s manual
Verbiage Copy
installation instructions
Receiving:
Immediately upon receiving your Jetta bath, inspect it thoroughly for freight damage. If
damage is found, please note on bill of lading and contact JETTA Corporation immediately.
The surface should be protected at all times to prevent scratches.
Do not carry unit by the piping as this may cause leaks.•
Check color match before installation.•
Nothing should be placed in bath that would scratch or break it.•
Workmen in bath should be in stocking feet only.•
Testing...
Water test your unit prior to installation. Set the tub on a level surface where it can be
drained after testing. Insert drain tting and ll to the overow. Make sure all ttings,
through walls and piping are water tight. While each unit is leak tested at the factory, the
process of shipping and handling may loosen joints. If there are leaks, mark the spot(s),
drain and repair with GE Silicone Sealer (ber glass to PVC) or PVC cement (PVC to PVC).
Repeat test when dry.
Rough-In...
Test t the tub, and verify dimensions. Your Jetta bath should be installed in a bedding compound, preferably a
mortar mix or thin set, which should be distributed under the base to provide maximum support and even weight
distribution. Do not use foam, sand or drywall mud. When leveling, prepare a bed of moist mortar in the area where
bath is to be installed. Place equally spaced mounds of bedding compound, about one foot apart, 2” to 4” tall - this
should be about the diameter of a three pound coffee tin (8”-10”). When the bottom of the tub comes in contact
with the bedding compound, it should compress the mounds to a 1” to 3” layer while the tub should lightly rest on
top of the tub deck. Once the bedding compound drys, all of the weight will be carried through the oor of the tub,
not suspended by its lip. Carefully level the unit, ensuring that uniform support is given to all areas of the base
and that no portion of the lip is bearing weight. DO NOT SUPPORT THE WEIGHT OF THE BATH BY THE RIM!
Since your Jetta bath has a pre-leveled lip that accounts for the sloped oor towards the drain, the 1” x 1” drain board
attached to the bottom of the tub does not need to be removed. It is recommended that plastic is laid between the bed-
ding compound and the bath, in case removal of the bath is ever necessary.
Use union connections only for the pump. Do not overtighten. Make sure the O-rings on the pump are in place.
Hand tighten pump ttings. Do not use a wrench, channel locks, or pipe dope (teon paste).
IMPORTANT: MANUFACTURER WILL NOT BE LIABLE FOR THE REMOVAL OR RE-
INSTALLATION OF THE BATHTUB IF THERE IS A FAILURE TO FOLLOW THE MANU-
FACTURERS RECOMENDED PRE-INSTALLATION AND INSTALLATION PROCEDURES,
FAILURE TO FOLLOW THE MANUFACTURERS RECCOMENDATIONS COULD RESULT
IN THE WARRANTY BEING VOIDED.

7
© 2013 Jetta Corporation. All rights reserved. REV 05/2013
www.jettacorp.com
owner’s manual
optional skirt installation instructions
The skirt may need to be trimmed to size. Take the measurements of the skirt opening and compare1.
those of the skirt itself to determine if the skirt must be trimmed to t. If so, mark the dimensions on
the skirt and trim the skirt on the bottom and sides (do not trim the top of the skirt) and cut to within
1/8” of the required dimensions using a circular saw with sharp tooth blade. It is recommended using
a belt sander to nish trimming the sides and bottom of the skirt to the exact size of the opening.
To create a positive stop for the skirt, nail, glue or screw 2x2” or 2x4” wood blocks on both side walls2.
and along the full length of the front oor section (parallel to tub lip). The wood blocks must be mount-
ed securely against a wall or stud wall framing and the oor.
The top of the skirt is notched. Foam blocks are glued to the top backside of the skirt (section that is 3.
notched) and will compress to hold the skirt against the bathing well of the tub. Check the underside
of the tub lip for smoothness…there may be berglass chop that requires sanding so the skirt will t
snugly in place. Slide the notched top edge of the skirt under the lip of the tub. Move the bottom
section of the skirt in place until it is resting against the wood blocks. Verify the vertical edge of the
skirt is perpendicular to the oor.
Included with the skirt are two screws and decorative caps that cover /conceal the screw head and are4.
color matched to the acrylic. Drill two (2) screw holes in the bottom of the skirt – to protect the acrylic
from cracking – position to align with wood block. Screw both lower ends of the skirt through the deco-
rative caps -- through the acrylic and into the wood blocks -- to hold the skirt securely in place.
Note: the skirt is not marked where the screws should be positioned as application will dictate position.
Installer may then seal the sides and oor with caulk or silicone if so desired. 5.
Parts included for optional skirt installation:
• (1) skirt
• (2) Screws
• (2) Decorative caps
• (1) Instruction sheet
Parts / tools needed for optional skirt installation that are NOT included:
• Circular saw with sharp tooth blade and a belt sander
• Drill
• 2x2” or 2x4” wood blocks
• Caulk or silicone
• Screw driver
• Tape measure
• Square / level

© 2013 Jetta Corporation. All rights reserved. REV 05/2013
800-288-7771
8
owner’s manual
maintenance &cleaning
Cleaning:
Cleaning should be done with a damp cloth and a window cleaner (i.e. Glass Plus, Windex, etc.). 1. NEVER
WITH ANY SOLVENTS. Do not use an abrasive or chemical based cleanser of any kind. The ttings should
be wiped off with a damp cloth only. Bubble Bath or bath oils are not recommended for whirlpool, air or
combination baths. See dealer for specic cleaners.
If you desire additional lustre on your bath surface, you may use a good automotive wax recommended2.
for plastic surfaces. Do not wax the oor, for this may cause a slip hazard. Light scratches and abrasions
may be removed and the original gloss restored by using a light bufng compound. Use a damp cloth, rub
in small circles until scratches or abrasions are gone, then wipe with a dry cloth until the original gloss is
restored.
Repairs of any kind, if necessary, should be done by qualied acrylic experts. 3.
Proper installation and maintenance will ensure years of service and make you proud to own a bath by4.
Jetta Corporation.
It is recommended that your whirlpool, air or combination system be ushed twice per month. More frequent
service may be required depending on usage.
Flushing Procedure:
Fill your bath with hot water.1.
Add 2 tablespoons of low-foaming automatic dishwasher detergent (i.e. Cascade, Sunlight, etc.)2.
Add 1/2 cup of household bleach to the water.3.
Run the whirlpool for a minimum of fteen minutes.4.
Drain Bath5.
Rell with cold water and operate the whirlpool for fteen minutes.6.
Drain Bath.7.
NEVER operate a whirlpool bath without rst lling the tub with water to 2” above
operating jets (some models allow upper jets to be shut down for operation at a
lower water level).
Repair:
If any problems should develop, call your installer, dealer or the factory at [phone].

9
© 2013 Jetta Corporation. All rights reserved. REV 05/2013
www.jettacorp.com
owner’s manual
operating instructions
Classic Series
The bath should be lled 2” over the directional jets BEFORE turning the pump on.
Directional Body jets:
To increase the directional jet pressure, grasp the outer ring of
the jet and turn clockwise, to reduce jet pressure turn the outer
ring
counter-clockwise.
To adjust the jet direction, use your nger to position the jet
nozzle to the desired location.
To remove jet, grasp the outer ring of the jet and turn counter
clock-wise until the jet clicks – then pull jet out.
To install a jet, insert the jet into the jet housing (do not force
the jet) and turn clockwise until the jet clicks – will pass a
point of resistance.
When bathing is complete, the pump must be turned off and the bath emptied. Adjust the inner
nozzle portion of the all the jets in a downward position while draining the bath, to allow the bath
to drain properly.

© 2013 Jetta Corporation. All rights reserved. REV 05/2013
800-288-7771
10
owner’s manual
operating instructions
Designer & Elite Series
The bath should be lled 2” over the jets BEFORE turning the pump on.
Rotating Back Jets:
To increase the jet pressure, grasp the outer ring of the jet
and turn clockwise; to reduce jet pressure turn the outer ring
counter-clockwise.
The upper rotating back jets can be shut-down for operation at
a lower water level. When shut down, the rotating jets will still
have a small ow of water.
To increase rotation, use your nger to position the jet nozzle
closer to the outer ring; to decrease rotation, position the jet
nozzle closer to the center of the jet.
Directional Body jets:
To increase the jet pressure, grasp the outer ring of the jet
and turn clockwise, to reduce jet pressure turn the outer ring
counter-clockwise.
To adjust the jet direction, use your nger to position the jet
nozzle to the desired location.
To remove jet, grasp the outer ring of the jet and turn counter
clock-wise until the jet clicks – then pull jet out.
To install a jet, insert the jet into the jet housing (do not force
the jet) and turn clockwise until the jet clicks – will pass a
point of resistance.
When bathing is complete, the pump must be turned off and
the bath emptied. Adjust the inner nozzle portion of the all the jets in a downward position while
draining the bath, to allow the bath to drain properly.

11
© 2013 Jetta Corporation. All rights reserved. REV 05/2013
www.jettacorp.com
owner’s manual
operating instructions for optional air bath feature
Mood Light
Optional Heated Quiet-Flo Blower

© 2013 Jetta Corporation. All rights reserved. REV 05/2013
800-288-7771
12
owner’s manual
operating instructions for optional air bath - purge cycle

13
© 2013 Jetta Corporation. All rights reserved. REV 05/2013
www.jettacorp.com
owner’s manual
troubleshooting
Jets are not operating properly.
The jets may be blocked or closed. Check every jet to ensure that each one is open by rotating the outer ring in a
clockwise direction. If water still is not moving through the jets at the desired rate, turn the motor off. Check the
suction to remove any debris that may have collected. Reattach the suction cover before operating again.
Pump will not start.
Check to ensure that power is owing to the electrical outlet. After inserting the plug fully into the outlet, reset the
GFCI. Check to see if the air hose is connected to both the pump and the on/off switch located on the under mount
of the bath.
NOTE: The pump can not operate if the bath is not lled with 2” of water above the top jets.
Water leaks around pump.
Check to see if the black union nuts on the pump are tight and if the O-rings are sealed properly. Loosen the unions
from the PVC, reset the O-rings for proper seating, and then tighten the union nuts BY HAND until seal is formed.
Tub will not come on.
Check to see if there is power to the receptacle by plugging in a light or a hair dryer. The GFCI controlling that
circuit may be tripped. If you push the button and it still does not come on, verify that both ends of the clear vinyl
tubing are connected to the transmitter body on tub and air switch on motor.
Tub will come on by itself.
If you turn the button and the tub does not shut off, the switch may be defective. Call your Jetta rep for replace-
ment. If you have a push button and the tub comes on by itself, pressure may be built up inside the clear vinyl tub-
ing (cvt). To x this, punch a small hole into the cvt to release the pressure. The hole should be no larger than the
tip of a screw.
Tub will not shut off.
If you have a push button and the tub does not shut off, the red vinyl tubing may not be connected to transmit-
ter body on tub or the air switch on motor. If you have a turn button, the relay may be stuck. Tap on rectangle box
located on top of motor (2” to the right of where the power cord enters the box on the vertical surface of the
rectangle box), this should release the stuck points in the relay.
Motor comes on and hums.
This condition may be a symptom of the pump shaft being stuck due to the build up of minerals, or debris collecting
on the impeller on the pump. Unplug the pump motor and locate the fan cover on the back end of the pump. With
the pump unplugged, insert a screwdriver through the center hole in the fan cover and attempt to rotate the pump
shaft. If the shaft rotates but the pump still does not operate properly the pump assembly may have to be replaced.
Motor comes on but will not push water.
First check to see if the jets turned on (clockwise opens, counterclockwise closes). If they are on and the motor still
does not push water, the pump may be mounted too high (this will be a problem on new installs only), and air may
be trapped in the line. Remove 1 pump board from under the motor and lower the motor accordingly. Foam may
have to be chipped away from the ex lines to accomplish this.
Trissage will not work.
If the trissage runs on low speed only, the trissage hose may be cut or the nipple on trissage body may be broken.
If trissage runs on high speed only, motor may not be drilled for trissage. Please contact your Jetta dealer for re-
placement parts.
The light will not come on.
Since the light has a separate power source, rst check to see if the light is plugged in and the bulb isn’t burnt out.
If it still doesn’t work, check to see if the red vinyl tubing is connected correctly to the transmitter body on tub to
the transformer box (small mounted rectangular black box) on the tub base.
How do I change a defective bulb?
The bulb can be changed from inside the tub. Each light is supplied with a special wrench, which has square
corners to t the wall tting square corners. Unscrew the wall tting, and making sure the “O” ring does not
fall out. The light bulb pulls straight out for removal, and pushes straight in to install.
If unit is within the limited factory warranty, contact Jetta Corporation at (800)-288-7771
with your purchasing information on hand, so that we may service you better.

© 2013 Jetta Corporation. All rights reserved. REV 05/2013
800-288-7771
14
10 Year Limited Warranty
This warranty gives the original consumer / purchaser specic legal rights. You may also have additional rights which vary from state to state. All
written or implied warranties are limited to the durations expressed below. Any damages, including loss of time, inconvenience, loss of residence
and water damage, and any other incidental or consequential costs, expense or damage are excluded from this warranty. All items must have been
installed and maintained in accordance with the Jetta Owner’s Manual. All units must be water tested before installation to validate warranty.
Accessories not factory installed are not covered under this warranty.
Covered Products:
Jetta Corporation covers the surface nish and structure of soaking, air, and whirlpool baths plus their support equipment, controls and plumbing
equipment for the Jetta J-Line and WaterDance Baths by Jetta products, unless specically noted by Jetta Corporation at time of purchase.
Structure and Surface Warranty:
The original consumer / purchaser of a Jetta Corporation soaking, air or whirlpool receives a limited warranty that includes the following:
• All residential baths are covered by a 10-year limited structural and surface warranty.
• All commercial, hotel or industrial baths are covered with a 1-year limited structural and surface warranty.
• The shell will be free of water loss due to defect and will retain its structural integrity.
• The surface will not fade, crack, blister, or delaminate due to defect. This surface warranty does not apply to fading, cracking,
blistering or delamination due to excessive wear, sun fading or improper cleaning.
Equipment Warranty:
The original consumer / purchaser of a Jetta Corporation soaking, air or whirlpool receives a limited warranty that includes the following:
• All residential baths are covered with a 5-year equipment warranty (equipment includes pump, motor, blower, plumbing parts &
ttings and controls) and a 1-year labor warranty.
• All commercial, hotel or industrial baths are covered with a 1-year equipment warranty (equipment includes pump, motor, blower,
plumbing parts & ttings and controls) and a 1-year labor warranty.
• Equipment as stated is warranted to be free of defect in workmanship and material for the period noted.
Warranty Limitations:
1. Jetta Corporation reserves the right, at its option to a) repair or replace the defective unit b) repair or replace the defective
components, or c) replace with an equal-valued unit.
2. This warranty extends only to the original consumer / purchaser and is not transferable.
3. The structure and surface warranty is valid for ten (10) years for residential baths and one (1) year for commercial, hotel or
industrial baths from date of manufacture.
4. The equipment warranty is valid for ve (5) years for residential baths and one (1) year for commercial, hotel or industrial baths
from date of manufacture.
5. This warranty may not be amended by any other than Jetta Corporation, and this remains the sole warranty for Jetta Corporation baths.
6. This warranty covers only factory installed accessories.
7. All light bulbs, pump seals, air injectors, O-rings, jet trim, pillows, waterfall ll spout, waste & overows, and skirts are warranted to be
free from defects for ninety (90) days from date of purchase.
Warranty Exclusions:
1. Jetta Corporation warranties do not cover defects due to shipping damage, installation errors, use other than non-bathing purposes,
abuse, misuse, failure to provide maintenance and / or cleaning as directed in the Owner’s Manual, accident or acts of God. Any
modications, alterations or customization made by an unauthorized service representative or without authorization by Jetta
Corporation will result in warranty becoming null and void.
2. This warranty does not cover costs associated with installation, removal or installation of replaced unit.
3. This warranty does not include freight charges associated with return of components or unit for repair nor freight charges associated
with replacement components or unit.
4. The warranty does not include any costs associated with electrical modications or plumbing modications.
5. The forgoing warranty is exclusive and in lieu of all other warranties, including any other warranty of quality, express or implied,
and including any warranty of merchantability, or any warranty of tness for any particular use.
Warranty Service:
In order to make a claim under this warranty, the original consumer / purchaser must notify Jetta Corporation in writing no later than fteen (15)
days from occurrence, and must be within the expressed warranty period(s). Provide a description of the problem, serial number of bath or proof
of purchase. Labor includes costs that are deemed typical and customary and must be approved by Jetta Corporation or authorized representative
prior to repair in accordance with above conditions and limitations. This warranty excludes any labor incurred due to insufcient access to compo-
nents, including but not limited to electronics, pumps, blowers and plumbing. Send claim to:
Jetta Corporation
Warranty Service Department
425 Centennial Blvd.
Edmond, OK 73013
[phone] or [phone]
Fax: [phone]
With the issuance of this warranty, Jetta Corporation stipulates, and the purchasers agrees, that in the event of litigation is instituted as a result of
this limit warranty, said litigation will be controlled by the applicable laws of the State of Oklahoma, and the buyer and seller both agree that the
appropriate forum and venue for any such litigation will be in Oklahoma County, State of Oklahoma.
For Jetta J-Line and WaterDance Baths by Jetta product lines.

425 Centennial Blvd.
Edmond, OK 73013
Corporate [phone]
Toll Free [phone]
Fax [phone]
www.jettacorp.com
REV 05/2013
tub label