JINJUNYE Aquajack 600 User manual

Robotic pool cleaner for aboveground pools
Instruction manual
Battery: 7.4V /4000mAh
Charging power: 8.4V DC, 1.5A
Motor voltage: 7.4V DC
Waterproof grade: IPX8
600
Give time to home, Give home to JINJUNYE

1
The cleaner is not a toy, and is operated by people older than 8 years age.
Any people who operates the cleaner, has to read the manual carefully
before work it.
(1)The cleaner is designed to clean the swimming pool, SPA.
(2)Please use the original batteries and charger when using.
(3)Only charging it when the cleaner is power off.
(4)Put the cleaner into a clean and dry place. Do not expose it under the
sun, or close to explosive.
(5)The filter bag is easy to be broken when there is sharp substances under
water.
(6)
The cleaner automatically stops to work when it is out of water.
(7)Do not close to the vacuum head when it is working, due to its suction
power, especially for the human body, animals, hairs or clothes.
(8)Do not disassemble the cleaner without professional guidance or notice
from the authorized distributor or manufacturer.
(9)Do not leak the lubricant oil, and it causes water polluted.
(10)Stop to work the cleaner when there is anything wrong; Please contact
with the authorized distributor or replace it to the original parts/accessories.
(11)Cleaner working conditions:
(11)-1 Maximum applicable water depth: 3 m (10 ft)
(11)-2 Water temperature: 4°C( 39.2°F )-35°C( 95°F )
SAFETY WARNING
1. Charger
Warning!
When installing and using this electrical equipment, you should always
follow the basic safety precautions. Please read the following carefully
(1)Use the original charger provided only.
(2)For indoor use only. The charger should not be used outdoor and not
be exposed to rain, humidity, any liquid or heat.
(3)Keep the charger out of children.
(4)Never use the charger if any damage is found.

2
(5)Do not handle the cleaner and charger with wet hands and bare feet，
when charging the cleaner.
(6)Disconnect the charger from power when not in use.
(7)If the wire is damaged, it must be replaced by a new charger to avoid
danger.
(8)Make sure the cleaner and charger are totally dry before charging.
(9)Charge the cleaner 4-5 hours prior to the first use.Normally cleaner can
be operated about 60 minutes after fully charged.
Above warning and cautions are not intended to incorporate all possi-
ble instances for risks and/or severe injury. Pool/spa owners should
always exercise intensive caution and common sense when operating the
cleaner.
2. Battery disposal
(1)The cleaner battery is a lithium battery, it must be disposed properly,
please contact with your local authority for more information.
(2)Never attempt to disassemble the lithium battery.
(3)Remove all personal items such as rings, bracelets, necklaces and watch-
es when unwiring a lithium battery from the vacuum unit.
(4)The battery causes short curcuit current, as well as severe burning when
it is high enough.
(5)Wear complete eye protection, gloves and protective clothing when
removing the battery pack.
(6)No smoking or sparkling flame near the cleaner, or, it may causes
unknow gases.
(7)If acid comes in contact with skin and clothing, wash immediately with
plenty of soap and water.
(8)If acid comes in contact with eyes, immediately flood eye with running
cool water for at least 15 minutes.Get medical attention immediately.

Assembly
Assembly and operation
Charging warning
3
A: Floater
B: Upper cover
B-1: Jet head
C: Filter
D: Bottom base
E: Charger
A
B
B-1
E
C
D
Switch
Charging port
Bottom cover body assembly bottom
There is a rotation jet head at the upper cover, the water is
passing from bottom to the jet head to make the robot
moving. While facing obstacle, the jet head turns around 180
degrees, the robot rounds the obstacle and moving by another
line. The rubbish is collected and installed by the bottom filter
cabine.
Use only the original external adapter and the charging cable
provided.
Make sure the robot and charger ports are clean and dry
before installation.
Power up the robot before using it for the first time (about 4-5
hours)
Note:
Once the robot starts charging, the
indicator light on the external adapter
will turn red. When the robot is fully
charged, the indicator light will turn
green.

4
1. 3.2. 4.
5.
Power on
When the robot has no power, it will automatically stop at the edge of the pool.(may also get stuck in the
middle of the pool by obstacles)
1. 2.
3.
Turn on the switch, loosen the rope on the float,
put the robot horizontally into the pool, and wait
for the robot to sink freely to the bottom. (if the
product is not put into the water, the machine will
not rotate because the machine has the function of
"stop when leaving water").
Adjust the length of the rope to ensure that
the length of the rope is at the same height as
the water level, and the extra length of the
rope is tied or cut short.
Open this place, you
can carry it by hand,
and take out the robot
easily
Garbage disposal
Note: 1. It is recommended to turn off the filtration system as the water circulation in the pool may affect the
robot's motion mode.
2. Any obstacle in the swimming pool will affect the robot's crawling and cleaning track, such as ladder;
3. If you are using a brine tank, make sure that all the salt is dissolved before putting the robot into the water.

Maintenance and storage
Maintenance and replacement of impeller
5
Recommended tool (not included): screw driver
Maintenance and replacement of wheels
Main wheel
Steering wheel
1. The battery discharges itself during storage. Make sure the robot is fully charged before storage.
2. When not in use, you must recharge the battery at least every three months.
•Unplug the external adapter from the socket and then the charging cable from the external adapter and the
robot.
•Remove the attachment from the robot. If necessary, rinse the robot and accessories with clean water. Do not
use detergent.
•Before storage, make sure the robot is drained.
•Use a wet cloth to clean and dry the robot and its accessories.
•Store in a well ventilated place away from sunlight, heat, fire sources, pool chemicals and children.
•The storage environment temperature should be 10
°C – 25
°F
(50
°C
– 77 °F ).
Note: higher storage temperatures may shorten battery life.
Note: the main wheel on this side has
magnets. Please contact the dealer for
replacement or maintenance.
1. 23.
Impeller
.

Battery assembly and replacement
Do not treat electrical appliances as unclassified municipal waste, use separate collection facilities. For
information on available collection systems, contact your local government.
Do not remove the lithium battery without authorization.
When removing the lithium battery from the vacuum device, please remove the ring, bracelet, necklace and
watch.
The short-circuit current generated by a battery is enough to adsorb the ring (or similar items), causing severe
burns.
Before removing the battery pack, please wear eye protection cover, gloves and protective clothing.
Be careful not to touch the wire or any metal parts, or it will cause spark or short circuit.
Do not smoke, spark or flame near the cleaner, or it will ignite the battery and produce gas.
Avoid exposing the battery to fire or high temperature, otherwise it may cause explosion.
Warning!
6
Note!
In case of battery leakage, avoid contact with the damaged battery and put it in a plastic bag.
If skin or clothing is in contact with acid, wash immediately with plenty of soap and water.
If the eyes are in contact with acid, rinse the eyes with water for at least 15 minutes and send them to a doctor
for treatment.
Battery replacement
1.Pull out the four clips of the core part of the upper cover outward and separate it from the body assembly of the bottom cover.
3. Open the battery cover, find the
battery connection line, press the
clip on the connector, pull it out, and
take out the battery.
Note: wrap the connector with
insulating tape immediately to avoid
short circuit caused by contact
between two wire terminals.
4. According to the disassembly steps, re install the battery and assemble the charging parts.
Note: (1) if there are impurities in the seal ring, clean it and install it back into the seal ring groove.
(2) Pay attention to the assembly direction. The six screw holes must be aligned to lock the screws.
2. Use a screwdriver to
remove all screws on the
power cover of the
bottom cover.
NOTE: User must consult dealer before any battery replacement.

Trouble shooting
Problem Possible causes Solution
Robots don't capture debris.
The battery is low.
Impeller stuck.
Impeller damaged.
The glove box is full.
The robot was stopped by an
obstacle. Check the cleaner for obstructions.
Remove obstacles.
Clean the glove box and filter cover.
Then charge the robot.
7
Please contact your dealer for replacement.
If you have problems with your cleaner, follow the troubleshooting steps below to restore performance.
Note: turn off the power before making any repairs.
Turn off the power supply of the robot and
visually check whether the impeller rotates. If
necessary, contact your dealer for further
instructions. Warning! Before servicing the
equipment, make sure that the robot is turned
off.
The robot stops moving in
the middle of the pool (the
rotating head is still
turning).
The robot is blocked by the suction
of the main pool floor drain. Turn off the filtration system (see
instructions in the manual).
The glove box is full. Clean the glove box and filter cover.
The operation time was shorter
than expected. Clean the filter chamber and recharge the
robot for 4-5 hours
The water circulation generated
by the filtration system interrupts
the direction of movement.
Turn off the filtration system (see
instructions in the manual).
The wheel is stuck. Check and remove debris from the wheels.
Clean the glove box and filter cover.
The glove box is full.
The glove box is full, check and remove any
debris that may be stuck under the rotating
head. It can be rotated by hand and rinsed
with water until smooth.
Clean the glove box and filter cover.
The bottom of the swivel is
stuck.
The glove box is full.
The turning head does not
rotate or rotates obviously
slowly.
The robot moves slowly.
The robot cannot cover the
entire pool / move along
the wall of the pool.
The ground is not totally flat
It takes more minutes before moving again
or Make the bottom of the pool flat or trim
the bottom brush strip. Contact your dealer
for replacement parts.

8
The debris escaped from the
robot.
The valve of the suction
nozzle (bottom of the
cleaner) is broken.
The baffle at the suction cup is like a door
to prevent debris from escaping from the
debris chamber. Contact your dealer for
replacement parts and instructions.
Debris enters the outside of
the filter cover. The filter cover is damaged. Replace the filter cover with a new one. Please contact your dealer for
replacement parts.
Battery damage.
Please contact the dealer to replace the
battery. Warning! Don't turn on the robot and
replace the battery yourself. This can cause
serious or fatal injury, so the warranty will
not be valid.
Charger is damaged.
Contact the dealer for replacement.
Warning! Using the wrong external adapter
will result in damage to the robot / battery
and void the warranty.
The robot can still work
without water. Remove hair and other rubbish with tools
Circuit board damaged Please contact the dealer for replacement.
The water of the robot is not
dry, and the contact is short
circuited, so the robot can still
work without water.
Leave it outside the water for a few
seconds and wait for the water to dry
There is garbage at the contact
point, such as wet hair, which
causes short circuit of the
contact.
If the charger shows red
light all the time, it cannot
change to green light more
than 8h.
If the charger change to
green light in a very short
time, and the device also
only work for a short
time(within half an hour,
need multiple validation).
When the product starts to
charge after the work is
over,if the charger shows
green light all the time.
( Make sure the charger cable
is properly and completely
connected to the external
adapter and robot. )
If the charger light does not
light any more.