JL Audio SB-F-SUPRCNSL/10W3v2 User manual

➔
➔
➔
➔
Stealthbox®
INSTALLATION GUIDE
SB-F-SUPRCNSL/10W3V2, JL AUDIO, Inc 2005 Sheet SKU#011149 Revision 8/4/2005Page 1
for the
SB-F-SUPRCNSL/10W3v2
(‘98-Up Ford SuperDuty
250,350,450,550 & 650
‘00-Up Excursion)
This Stealthbox is a product which
requires professional installation skills and
tools.
Please read this installation guide thor-
oughly before beginning the project. It
will guide you step by step through the
installation.Several of the steps in this
process may require two people to
accomplish.
It is absolutely vital that the enclosure
be properly mounted to the vehicle
according to these instructions. Failure
to mount the enclosure properly pres-
ents two problems: 1)The sub-bass
performance will suffer due to the
movement of the enclosure caused by
the force exerted by the woofer(s) and
2) A loose enclosure presents a serious
safety hazard in the event of a collision
or sudden deceleration.
Please enjoy your JLAudio Stealthbox
responsibly.
STEP 1: From inside the factory console,
using a 9/16”socket, remove the four bolts
that secure the console to the vehicle. (Two
of these bolts will be used later to secure
the Stealthbox).
STEP 2: Remove the console from the vehi-
cle.
STEP 3: Remove the inside section of the
console. (This will not be reinstalled).
-Two screws are located under the front tray.
-Three screws attach the hinge.
-Three screws are located on each side of the
consoles shell (six total)
After this section is removed,the console shell
will be in two parts.
STEP 4: Using a pair of pliers,from the inside
of the console shell.Remove the ridges locat-
ed toward the front of the console.
STEP 5: Reassemble the front and rear parts
of the console shell using the supplied hard-
ware (4 #8 x 1/2”long screws, 4 washer and
4 nuts) as shown in the picture.
STEP 6: Turn the console shell upside down.
Position the Stealthbox inside the shell,
START
HERE
Continued on Next Page ➔
www.jlaudio.com
➔
➔
STEP 7: Use the remaining mounting holes as a
drill guide.
Using a 1/8” drill bit and drill, drill a hole through
each of these guide holes, into the Stealthbox.
STEP 8: Install #8x 1/2” black pan-head screws
into the drilled holes.

➔➔
➔➔➔
STEP 10: Install #8 x 1/2” black pan-head screws
into the drilled holes.
Cont..
From
Previous
Page
Continued on Next Page ➔
➔
STEP 11: Using a 1/8” drill bit and drill. Drill two
holes at the hinge area using the outside holes only.
The center hole does not need to be drilled.
➔
STEP 12: Remove the screws installed in STEP 8
and STEP 10. Separate the console shell from the
Stealthbox.
STEP 13: Attach the OEM’s console lid to the
shell. Use one of the OEM’s screws and supplied
speed-clip to the center hole of the hinge.
STEP 9: Turn the console right-side-up with the
Stealthbox attached.
Using the holes on the top of the console shell as
guides, use a 1/8” drill bit and drill to drill holes
through each of these guide holes and into the
Stealthbox.
SB-F-SUPRCNSL/10W3V2, JL AUDIO, Inc 2005 Sheet SKU#011149 Revision 8/4/2005Page 2
www.jlaudio.com
STEP 14: Place the Stealthbox in the vehicle. Using
a pair of OEM bolts, from STEP 1. Loosely secure
the rear foot bracket to the floor, do not tighten.
STEP 15: Remove the paper backing on the sup-
plied sheet wax squares.
With the Stealthbox in place, lift the front of the
Stealthbox and position both supplied sheet wax
squares onto the carpet and lined up with the front
foot bracket of the Stealthbox, lower the console
down.
STEP 16: Using one of the supplied 3/8”x1-1/2”
bolts, place the bolt through each hole of the front
foot bracket (one at a time). Press down on the bolt,
too leave impressions on the sheet wax squares.
STEP 17: Remove the two OEM bolts from STEP
14. Remove the Stealthbox from the vehicle.

➔➔
➔➔➔
VEHICLE SHEET METAL
METAL BRACE PLATE
FLAT WASHER
HEX NUT
FRONT MOUNTING BRACKET
OF BRACKET
LOCK WASHER
FLAT WASHER
BOLT
STEP 19: Run speaker wire to the Stealthbox’s
location. Make sure the speaker wire is going to be
accessible at the rear of the Stealthbox.
*At this time, double check for proper oper-
ation of woofer*.
Cont..
From
Previous
Page
Continued on Next Page ➔
➔
STEP 18: With a 1/8” drill bit and drill, drill a pilot
hole.
With a 1/2” drill bit and drill, drill a hole through each
of the two locations.
*Caution: Check under the vehicle for any
loose brake lines,fuel lines, transfer case or
other hazards before drilling.Always wear
eye protection when drilling.*
➔
STEP 22: A second person is needed to help out in this
step.
Place a supplied flat washer onto each supplied 3/8”x1-1/2”
bolt. Place each bolt assembly through the front bracket of
the Stealthbox and the drilled holes from STEP 18.
From under the vehicle, place the supplied metal brace plate,
flat washer, lock washer and nut onto each bolt assembly.
With a second person inside the vehicle securing the bolt
head with an open-end wrench.Tighten the nut onto the
bolt assembly.
STEP 21: Replace the OEM bolts back to
the rear foot bracket. Hand-tighten the rear
bolts.
SB-F-SUPRCNSL/10W3V2, JL AUDIO, Inc 2005 Sheet SKU#011149 Revision 8/4/2005Page 3
www.jlaudio.com
STEP 25: Tighten the bolts at the rear of the
Stealthbox,inside the vehicle.
STEP 26: Connect the speaker wire to
the terminal cup on the Stealthbox. STEP 27: Place the pair of supplied alu-
minum spacers over the two holes that are
located at the upper rear of the Stealthbox,
From STEP 11.
STEP 20: Position the Stealthbox back into place.

Specifications:
Enclosure Type: Sealed
Driver Type: 10W3v2-D6
Nominal Impedance: 3Ω
Cont.. Power Handling: 300 Watts
JLAudio recommends using a high quality amplifier such as the JLAudio 250/1. The diagram below shows the recommended
crossover,infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox®.
Included Hardware:
2) 3/8” x 1-1/2” bolts
2) Sheet wax squares
4) flat washer
4) #8-32 Kep nuts
2) Felt pads
2) 3/8” Lock washer
2) 1/2” Aluminum spacers
4) #8-32 x 1/2” Machine screws
4) #8 x 1/2” Sheet metal screws
4)#8 x 1-1/4” Sheet metal screws
1) Metal Brace Plate
10369 N. Commerce Pkwy, Miramar, Florida 33025-392 Phone: [phone] Fax: [phone]
JL AUDIO 250/1
monoblock subwoofer amplifier
Amplifier Input Section
Input Sens.
Input Voltage
Low/High
Left Ch. Right Ch.
Signal Sensing
Off/On
Output Mode
Full-Range/Low-Pass/High-Pass
Left Ch. Right Ch.
Amp LP Filter
Mode/Slope
Off/12dB/24dB
Filter Freq. (Hz)
Bass Control
LF Boost (dB)
Off/30Hz
Infrasonic Filter
+1 +13
+3
+7
+10
Preamp Output Section
+12VDC Ground Remote
The JLAudio 250/1 is a very versatile audio component. Please consult the owner’s manual for detailed information
about installing and tuning this amplifier.
➔➔➔
STEP 28: Position the OEM console shell over the
Stealthbox.
*Make sure that the aluminum spacers from
STEP 27, do not move from their location.*
STEP 32: Place the supplied pair of felt pads
between the lid and the console shell.This is going
to prevent vibration contact of console storage lid
and console shell.
➔
SB-F-SUPRCNSL/10W3V2, JL AUDIO, Inc 2005 Sheet SKU#011149 Revision 8/4/2005Page 4
www.jlaudio.com
Mid/High Frequency Driver Information:
CONGRATULATIONS!
INSTALL COMPLETE.
XR570-Csi
TR570-Cxi
Front Location Driver Size:
5”x7”
Applicable JL Audio Products:
TR,VR, XR ZR570-Csi
Rear Location Driver Size:
5”x7”
Applicable JL Audio Products:
TR, XR570-Cxi
Cont..
From
Previous
Page
STEP 29: Insert the pair of supplied #8 screws
through the hinge holes (STEP 11) and into the
Stealthbox.
STEP 30: Reinstall the remaining supplied screws
that attach the console shell to the Stealthbox.
These screws were removed in STEP 12.
STEP 31: Replace the front tray.
Difficulty Scale