Jobsite IR-KIT MKII User manual

For Receiving and Routing Infrared
Commands from Any Remote Control
to Concealed Audio/Video Equipment
DATA SHEET
LCD/PLASMA PROOF IR REPEATER KIT IR-KIT MKII

IR-KIT MKII
LCD/PLASMA-PROOF IR REPEATER KIT
LCD/PLASMA PROOF IR REPEATER KIT IR-KIT MKII
FEATURES
IR-SMR MKII: SURFACE MOUNT IR RECEIVER
• LCD/Plasma proof design
• Rejects interference from flat panel displays,
CFL lighting or indirect sunlight
• Works with practically all remotes
• Green talkback LED indicates when A/V system is on
• Blue talkback LED confirms reception of IR signals
• 10' (304.8 cm) of connecting wire included
• Reliable adhesive backing
IR-E1: INFRARED EMITTER
• Infrared pass through housing
• Miniature size and shape
IR-CB2: CONNECTING BLOCK
• Provides two IR receiver inputs to accommodate
receivers with Zone 2 capabilities
• Selectable high/low emitter outputs for use with
IR-E1HO high output emitter
or single and dual emitters
• 12V DC status input jack and LED indicator
INSTALLATION FRIENDLY DESIGN
IR-SMR MKII
• 10' (304.8 cm) of connecting wire included
• Reliable adhesive backing
IR-E1
• 10' (304.8 cm) of cable with 3.5mm plug
• Reliable adhesive backing
• Includes IR blocking cover
IR-CB2
• Includes in-line UL listed regulated power supply
MOUNTING:
IR-SMR MKII AND IR-E1
• Self-adhesive surface mount
IR-CB2
• Wall or flat surface: use drywall screws
DIMENSIONS:
IR-CB2
• 5-11/16” wide x 1-1/4” high x 2” deep
144.5 mm wide x 31.8 mm high x 50.8 mm deep
IR-SMR MKII
• 2” wide x 11/16” high x 1/2” deep
50.8 mm wide x 17.5 mm high x 12.7 mm deep
IR-E1
• 5/16” wide x 3/16” high x 1/2” deep
7.9 mm wide x 4.7 mm high x 12.7 mm deep
SPECIFICATIONS
IR SYSTEMS:
• Works with practically all brands of IR remote controls
IR-SMR MKII
• IR receiving (varies by brand of remote control):
• 20'-35' (609.6 cm - 1066.8 cm) range
• From 20˚ to 30˚ degrees off-axis operation
• Wiring requirements:
• 10' (304.8 cm) of 4-conductor connecting wire is supplied
IR-E1 IR TRANSMITTING:
• 4' (122 cm) line of sight
• Emitter mounts directly to the IR window of a component
• Wiring requirements:
• 10' (304.8 cm) of 2-conductor 24-gauge wire with a 3.5mm
plug is supplied
• Use 18 gauge for distances up to 20' (609.6 cm) and 16
gauge for up to 200' (6096 cm)
IR-CB2 CONNECTIONS:
• 2 receiver inputs, 5 emitter outputs
• Wiring requirements:
• Cat-5 or better
• Home runs required from each IR receiver
• Power requirements:
• 110V to 12V DC power supply (included)
WARRANTY:
• 2 year limited
IR-KIT MKII
PART# FG01459

JOBSITE SYSTEMS
12331 SW 130 STREET
MIAMI, FL 33186
P 866.4JB.SITE (866.452.7483)
F 305.238.0185
WWW.JOBSITESYSTEMS.COM
©2007 JobSite Systems. All rights
reserved. JobSite, Pure Custom and Niles
are registered trademarks of Niles Audio
Corporation and the JobSite Logo is a
trademark of Niles Audio Corporation. All
other trademarks are the property of their
respective owners. CS0171A
Specifications subject to change without notice.
PREPARING FOR INSTALLATION:
While the IR-KIT MKII is compatible with most brands of audio/video
components, there are a few exceptions. You should perform a temporary
hookup to test for compatibility before you conceal wire or permanently
mount any parts.
INSTALLATION:
1. Place the IR-CB2 connecting block so that the emitter wires will reach the
components.
2. Place the IR-SMR MKII receiver in a convenient location near the television.
3. Insert each wire of the IR-SMR MKII receiver into the appropriate hole on
the removable connector plug of the IR-CB2 connecting block and snap
the locking tabs down. Insert the connector into the socket of the IR-CB2
connecting block.
4. Plug the emitters into the sockets labeled EMITTER OUTPUTS on the
IR-CB2 Connecting Block.
5. Position the emitters on each component’s IR sensor window using the
adhesive backing on the emitter.
6. Plug the connector on the supplied 12VDC power supply into the socket
labeled POWER on the IR-CB2 Connecting Block and then plug the power
cord into an electrical outlet.
7. To control your audio/video components, simply aim your remote control at
the IR-SMR MKII surface mount receiver.
IR-KIT MKII INSTALLATION DIAGRAM
LCD/PLASMA PROOF IR REPEATER KIT IR-KIT MKII