Johnson & Starley Reno HE16H User manual

Johnson & Starley
RELIABILITY YOU CAN TRUST
Publication No. ZZ 1190-4 September 2008
Product Identification No: 87B 074
HEAT
ONLY
SERIES
High Efficiency
Heat Only
Boilers
BS EN ISO 9001 : 2000
www.ener gysavingtrust.org.uk
The Johnson & Starley Reno range has an
energy rating A on a scale of A to G.
For more information see
www.boilers.org.uk
This is a certification mark.
www.johnsonandstarley.co.uk
USERS INSTRUCTIONS
Natural Gas G20:
Reno HE16H - GC No: 41-416-07
Reno HE25H - GC No: 41-416-03
Reno HE31H - GC No. 41-416-06
Propane G31 Variant:
Reno HE16HP - GC No: 41-416-11
Reno HE25HP - GC No: 41-416-13
Reno HE31HP - GC No. 41-416-10

THE BENCHMARK SCHEME
In order to comply with Building Regulations Part L (Part J in Scotland) the boiler
MUST be fitted in accordance with the manufacturer’s instructions.
Benchmark places responsibilities on both manufacturers and installers. The
purpose is to ensure that customers are provided with the correct equipment for
their needs, that it is installed, commissioned and serviced in accordance with the
manufacturer’s instructions by competent persons and that it meets the requirements
of the appropriate Building Regulations. The Benchmark Checklist can be used to
demonstrate compliance with Building Regulations and should be provided to the
customer for future reference.
Installers are required to carry out installation, commissioning and servicing work in
accordance with the Benchmark Code of Practice which is available from the Heating
and Hotwater Industry Council who manage and promote the Scheme.
Visit www.centralheating.co.uk for more information.
HEAT ONLY SERIES
High Efficiency Heat Only Boilers
www.johnsonandstarley.co.uk
2

CONTENTS
Benchmark Scheme 2
1. General Information 4
2. Layout of the User Panel 4
3. Initial Lighting 5
4. Operation of Boiler 5
5. Reset Function 5
6. Error Codes 5
7. Flame Loss 5
8. Boiler Overheating 6
9. Condensate Drain 6
10. Servicing & Maintenance 6
11. Escape of Gas 6
12. Cleaning the Appliance 6
13. Notes 7
3
Telephone: [phone]

2. LAYOUT OF THE USER DISPLAY
1. GENERAL INFORMATION
Part of the installation and commissioning of this appliance is related to
instructions for use by the heating engineer to the user where specific
requirements may occur, see note below.
.
This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety.
www.johnsonandstarley.co.uk
4
FIGURE 1
USER CONTROL PANEL
Central Heating Water
Temperature Control (P1)
Power
ON/OFF
Switch
Power ON Burner On Error code LED’s (1-6)

3. INITIAL LIGHTING
If turning on the boiler for the first time carry out the following
steps:
 Check that the electrical supply to the boiler is ON at the
external isolator.
 Ensure all hot taps are closed.
 Set any remote controls as required.
 Turn the CH control P1 to the minimum setting. Switch
on the appliance at the on/off switch on the control panel. The
boiler will then be in the STANDBY mode.
Only operate the boiler when you are sure that the system has
been correctly filled and vented. If you are in any doubt about the
boiler being filled with water contact your installer.
4. OPERATION OF THE BOILER
In order to turn on the central heating and adjust the temperature,
turn the control knob P1 to the desired setting between off and
maximum 82°C.
If the boiler is not required for an extended period turn the control
knob P1 fully anti clockwise to the off position. In this position the
frost protection will still be active.
5. RESET FUNCTION
Should a fault occur, tuRning the central heating water
temperature control knob P1 to RESET will clear the error and
enable the boiler to relight. If the fault recurs, turn off the boiler
and consult a CORGI registered installer.
6. ERROR CODES
Detailed on page 3 are error codes that you may encounter on
your boiler. For any sequences not illustrated , please refer to
your Installation & Maintenance Instructions or contact your local
CORGI registered installer.
7. FLAME LOSS
Should the flame signal be lost 5 times in any 4 minute period
the boiler will lockout and an error code will be displayed on the
series of LED’s as displayed below. Turning the central heating
water temperature control (P1) to the OFF position and then back
on again, will clear the error and enable the boiler to relight
If the fault recurs, turn off the boiler and consult a CORGI
registered installer.
5
Telephone: [phone]

8. BOILER OVERHEATING
In the event of the boiler overheating the boiler will lockout and
an error code will be displayed in the series of LED’s as detailed
below. Turning the central heating water temperature control P1 to
the OFF position and then back on again will clear the error and
enable the boiler to relight.
If the fault recurs, turn off the boiler and consult a CORGI
registered installer.
9. CONDENSATE DRAIN
The condensate drain must not be modified or blocked.
Blockage of the condensate drain caused by debris or freezing,
can cause the boiler to lockout.
If freezing is suspected and the pipe run is accessible, then
an attempt to free the obstruction by pouring hot water on to
the pipe may be made. If this fails to remedy the problem, the
assistance of a CORGI registered installer should be sought.
10. SERVICE & MAINTENANCE
It is recommended that a full maintenance check be carried out
annually on the appliance. It is also recommended to take out a
further service agreement on the expiry of the guarantee period.
You can obtain further information on this from your gas supplier.
The appliance should be checked /serviced by a CORGI
registered installer.
If you require service on your appliance please contact your local
installer or gas supplier.
On completion of the service the installer should fill in the service
section at the rear of the BENCHMARK log book. All installers
registered with CORGI carry an identification card. This card will
have an ID number which should be recorded in your logbook.
If you have any queries regarding your installer you can contact
CORGI by telephone on 01256 372400.
11. ESCAPE OF GAS
Should a gas leak be suspected contact your gas supplier with
out delay.
Do not search for leak with a naked flame.
12. CLEANING THE APPLIANCE
The appliance casing should only be cleaned with a damp cloth
then dried.
Do not use abrasive or solvent cleaners.
www.johnsonandstarley.co.uk
6

13. NOTES
7
Telephone: [phone]

Johnson & Starley
RELIABILITY YOU CAN TRUST
www.johnsonandstarley.co.uk
RENO BOILER RANGE
ECONOMAIRE WARM AIR HEATERS
HI-SPEC WARM AIR HEATERS
HEAT RECOVERY
HOME ‘N’ DRY VENTILATION
DRYFLOW
RENOXTRA
CENTRAL EXTRACT VENTILATION SYSTEM
DRAVO
Johnson & Starley are the leading UK &
European manufacturers of a complete range
of Domestic Warm Air Heaters.
All the heaters suit both Replacement and
Upgrade needs and are compliant with the
new (2006) amendments
to Part L of the
Building Regulations.
HOME COMFORT SOLUTIONS
Company Details
Website Address www.johnsonandstarley.co.uk
Email [e-mail]
[e-mail]
Telephone Number 01604 762881 (Main switchboard)
Fax Number 01604 767408
Spares
Telephone [phone]
Fax [phone]
Sales
Telephone [phone]
Fax [phone]
Service
Telephone [phone]
Fax [phone]
Warm Air Upgrade Enquiry Service
Telephone [phone]
Fax [phone]
COMMERCIAL & INDUSTRIAL
H&V SOLUTIONS
Company Details
Johnson & Starley Dravo Division Industrial H&V
Website Address www.dravo.co.uk
Email [e-mail]
Telephone Number 01604 707022
Fax Number 01604 706467