Jolly LX-740 User manual

USER MANUAL
LX-740
V1.0

Table of content
1.Open-Package guidelines........................................................... .1
１.１Package............................................................................. ...1
2.Safety instructions................................................................... ...1
3.Operating determination....................................................... ......3
4.Rigging the fixture................................................................. ......4
4.1 Mounting.......................................................................... .......4
5.
6.
7.
7.1
7.2
7.3
8.DMX protocol........................................................................... ..12
9.Maintance and cleaning...................................................... .......16
10.Electric equipment specification........................................ ......16
10.1 Electrical paramters.......................................................... ..16
10.2
10.3
............
............
............
............
............
............
4.2Installing the Clamps............................................................................4
4.3 Power supply connection and cut off...................................................5
4.4 Power Connection...............................................................................6
4.5 DMX-512 connection/connection between fixtures.............................6
............
............
............
............
............
............
............
8.1 Unit model..........................................................................................12
............
.............
.............
....................................................................16
Channel Characteristics...................................................................16
10.4 Menu Function.................................................................... .............17
10.5 light table........................................................................................17
11.Electronic drawing................................................................................18
Description of the device........................................................... ...7
Dimension.................................................................................. ..8
Display control......................................................................... ....9
Navigation in the Menu......................................................... ...9
Display Operation................................................................. ...9
Menu list................................................................................. 10
Weight and dimensions

Congratulations on choosing our products! Please carefully read this instruction manual in its
entirety and keep it well for using reference. This manual contained about the installation and
the relative using information of this products. Plese refere this manual's relative instruction
when using this equipment.

2.Safety instructions
1.Open-Package guidelines
１.１Package
Unpacking the fixture
1.Open the flight case cover
2.With one person on each side, lift the fixture out of the flight case.
Packing the fixture
1.Disconnect the fixture from power and allow it to cool.
2.Place the fix ture in the bottom of the flight case, and cover the case without forcing.
This equipment is made of new style,high intensity plastic.It fully shows the modem times light charac
teristic with beauty struture. And it is made accord to CE standard. Fully agree with the internation
512 agreement.
teris-
tic with
standard of DMX
1.Signal cable-1PC 2.Safty cable-1PC
3.User Manval-1PC 4.Omega holder-1PC
5.Power cable-1PC 5.Service card-1PC
When receive the product,please be careful to take and put,check if the product has damage or not be-
cause of transportation, and check the following parts:
This device has been shipped with our premises in absolutely perfect condition. In order to maintain this
ensure a safe operation ,it is absolutely necessary for the user to follow the safety instruc -
notes written in this manual.
Important:
The manufacturer will not accept liability for any resulting damages caused by the nonobservance of this
manual or any unauthorized modification to the device.
Please consider that damages caused by manual modifications to the device are not subject to warranty.
condition and to ti
ons and warning
Every person involvd with installation and maintenance of this device to:
-Be qualilfied
-Follow the instructions of this manual.
Note: to prevent the
lamp damaged, focusing
lens must return, can be
placed in the box.
- 1 -

Never let the power-cord come into contact with other cables! Handle the power cord and all connections
with particular caution!
Make sure that the available voltage is not higher than stated on the rearpanel.
Always plug in the power plug least. Make suer that the power-switch is set to off-position before you con
ections with themains with particular caution!
Make sure that the power-cord is never crimped or damaged by sharp edges.Check the decice and the p-
ower-cord from time to time.
Always disconnect from the mains, when the device is not in use or before cleaning it.
Only handle the power-cord by the plug,Never pull out the plug by tugging the powercord.
This device falls under protection class I.Therefore it is essential to connect the yellow/green conductor
to earth.
The electric connection,repairs and servicing must be carried out by a qualified employee.
Do not connect this device to a dimmer pack.
Do not switch the fixture on and off in short intervals as this would reduce the lamp’s life.
Do not touch the device’s housing bare hands during its operation(housing becomes hot)!
For replacement use lamps and fuses of same type and rating only.
t 90
c°C
IP20
t 40
a°C
Risk Gr oup 2
Accor ding to
En624 71
Eye damage!
Avoid looking directly into the light source(meant especially for epileptics)!
Minimum distance of illuminated objects
0.20 metres from the lens of the projector.
Maximum ambient temperature
Do not operate the fixture if the ambient temperatuer(Ta) exceeds 40°C (104°F).
Temperature of the external surface
The maximum temperature that can be reached on the external surface of the fitting,in a ther-
mally steadystate,is 90°C (194°F).
IP20 protection rating
The fitting is protected against penetration by solid of over 12mm (0.47”) in diameter (first
digit 2), but not against dripping water,rain,splashes or jets of water (second digit 0).
Indoor use only
Not suitable for household illumination
Photobiological Safety
CAUTION.Possibly hazardous optical radiation emitted from this product.Do not stare at
operating lamp.May be harmful to the eyes.
Light collimation system
This product contains internal light collimation system.Avoid intense light from any angle.
The products to which this manual refers comply with the European Directives purs-
uant to:
•2006/95/EC - Safety of electrical equipment supplied at low voltage (LVD)
•2004/108/EC - Electromagnetic Compatibility (EMC)
•2011/65/EU - Restriction of the use of certain hazardous substances (RoHS)
•2009/125/EC - EcoDesign requirements for Energy-related Products (ErP)
Protection against electrical shock
Connection must be made to a power supply system fitted with efficient earthing (Class I app-
liance according to standard EN 60598-1) .It is, moreover, recommended to protect the supply
lines of the projectors from indirect contact and/orshorting to earth by using appropriately
sized residual current devices.
The projector needs to be positioned so that the objects hit by the beam of light are at least
- 2 -
0.2

Disposing
This product is supplied in compliance with European Directive 2012/19/EU-Waste Electrical
and Electronic Equipment (WEEE) .To preserve the environment please dispose/recycde this
product at the end of its life according to the local regulation.
Battery
This product contains a rechargeable lead-acid or lithium iron tetraphosphate battery. To pre-
serve the environment,please dispose the battery at the end of its life according to the regul-
ation in force.
This device is a moving-head for creating decorative effects and was designed for indoor use only.
If the device ha been exposed to drastic temperature fluctuation(e.g.after transportation).do not weitch it
on immediately.The arising condensation water might damage your device,Leave the device switched off
until it has reached room temperature.
Never run the device without lamp!
Do not shake the device,Avoid brute force when installing or operating the device.
Never life the fixture by holding it at the projectorhead, as the mechanics may be damaged. Always hold
the fixture at the transport handles.
When choosing the installation-spot,please make sure that the device is not exposed to heat,moisture or
dust.There should not be any cables lying around.You endanger your own and the safety of others!
The minimum distance between light output and the illuminated surface must be more than 0.2 meters.
Make sure that the area below the installation place is blocked when rigging,derigging or servicing the fi-
xture.
Always fix the fixture with an appropriate safety rope, Fix the safety rope at the correct holes only.
Operate the fixture after having checked that the housing is firmly closed and all screws are tightly faste-
nd.
The lamp must never be ignited if the objective-lens or any housing-cover is open, as discharge lamps
may explose and emit a hign ultraviolet radiat, which may cause burns.
The maximum ambient temperature 40°C must never be exceeded.
Operate the device only after having familiarized with its functions. Do not permit operation by persons
not qualified for operating the device. Most damages are the result of unprofessional operation!
Please use the original packaging if the device is to be transported.
Please consider that unauthorized modifications on the device are forbidden due to safety reasonsl.
If this device will be operated in any way different to the one described in this manual, the product may
suffer damages and the guarantee becomes void.Furthermore, any other operation may lead to dangers
like short-circuit,burns, electric shict,burns due to ultraviolet radiation,lamp explosion,crash etc.
3.Operating determinations
- 3 -

4.1 Mounting
For the various mounting positions of the FIXTURE(standing on the floor, sideways or hanging different
accessories kits are available.
Through this a safe and firm installation is assured.
You’ll find special connectors on the bottom side of the system which are put to use here.
4.2 Installing the Clamps
Please consider the respective national norm s during the Installation!The installation must only be car-
ried out by an authorized dealer!
The installation of the projector has to be built and constructed in a way that it can hold 10 times the wei-
ght for 1 hour without any harming deformation.
The installation must always be secured with a secondary safety attachment, e.g.an appropriate catch
net.This secondary safety attachment must be constructed in a way that no part of the installation can
fall if the main attachment fails.
When servicing the fixture staying in the area below the installation place,on bridges,under high working
places and other endangered areas is forbidden.
The operator has to make sure that safety-relating and machine-technical installations are approved by
an expert before taking into operation for the first time and after changes before taking into operation an-
other time.
The operator has to make sure that safety-relating and machine-technical installations are approved by
an expert after every four year in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are approved by
a skilled person once a year.
The projector should be installed outside areas where persons m ay walk by or be seated.
Important!Overhead rigging requires extensive expering CE,including (but not limited to)calculating
working load limits, installation material being used, and periodic safety inspection of all installation ma-
terial and the projector. If you lack these qualifications, do not attempt the installation yourself, but inste-
ad use a professional structural rigger. Improper installation can result in bodilyinjury and or damage to
property.
The projector has to be installed out of the reach of people.
If the projector shall be lowered from the ceiling or high joists, professional trussing system s have
to be used. The projector must never be fixed swinging freely in the room .
Caution Projectors may cause severe injuries when crashing down! If you have doubts concerning the
safety of a possible installation, do not install the projector!
Before rigging make sure that the installation area can hold a minim um point load of 10 times the
projector s weight.
4.Rigging the fixture
Pay attention to the regulations of CE.
Installation by qualified staff to complete.
- 4 -

The projector can be placed directly on the stage floor or rigged in any orientation on atruss without alte-
ring its operation characteristics.
For overhead use,always install a safety-rope that can hold at least 10 times the weight of the fixture.You
must only use safety-ropes with screw on carabines.Pull the safety-rope through the two apertures on the
bottom of the base and over the trussing system etc.
Warning: it is necessary to make sure that
the installation location is perfectly appropriate,
and the installation location is safe and reliable.
1
2
12
3
4.3 Power supply connection and cut off
Connect the light source to the main power source with the plug of the power cord, or cut off the power
supply:
Connection: according to procedures, the power
plug and socket is inserted into the groove one one
alignment,rotation.
Cut off:according to procedures,press the button
on the rotating plug,pull out.
- 5 -
Mounting plate
Secure chain Omega holder

2 1
3
2 1
3
5 1
4 2
3
5 1
4 2
3
5 1
4 2
3
1:Ground
2:Signal(-)
3:Signal(+)
1:Ground
2:Signal(-)
3:Signal(+)
4:N.A.
5:N.A.
2 1
3
5 1
4 2
3
4.5 DMX-512 connection/connection between fixtures
Only use stereo shieded cable and 3-pin XLR-plugs and connectors in order to connect.
Caution
At the last fixture,the DMX-cable has to be terminated with a terminatou. solder a 120 resistor between
signal(-) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture.
DMX iutput
3-pin XLR socket
DMX iutput
5-pin XLR socket
DMX output
3-pin XLR socket
DMX output
5-pin XLR socket
4.4 Power Connection
mains with the enclosed power cable and plug.
If you wish to change the power supply settings, see the chapter appendix Connect the fixture to the
L
N
CABLE(EU) CABLE(US) Pin
Brown Black Live
Yellow/Green Green Earth
Light blue White Neutral
INTERNATIONAL
Standard edition
DMX512
Warning: please verify the power of the power
supply equipment prior to the connection! Earth wire
must be grounded!
- 6 -

5.Description of the device
DMX Terminator Diagram
-For installations where the DMX cable has to run a long distance or
is In an electrically noisy environment it is recommended to use a
DMX terminator. This help in preventing corruption of the signal by
electrical noise. The DMX terminato r is simply an XLR plug witha
120 resistor connected between pins 2 and pins3, which is then
plugged into a the output XLR socket of the last ifxture in the chain.
Ω
1
2
3
120Ω
PIN2 PIN3
- 7 -
Head
Tilt °, 228 Fixture could auto
reset.
3.
Arm
Pan °,450 Fixture could auto
reset.
Base
2.
1.
4.5-pin XLR female
5.5-pin XLR male
6. display
7.power in
8.power out
9.MODE button
10.UP button
11.DOWN button
12.ENTER button
European standard edition
4
5 6
7
8
910
11 12

6.Dimension
- 8 -
250 mm
165 mm
160 mm
88 mm
336 mm

7.Display control
7.1 Navigation in the Menu
7.2 Display Operation
Using the buttons or touch screen, and this can be simply and easily set the address code and
code.
functions
If you view or modify the lighting feature set, then press ENTER button, the display will enter the menu
interface. Both there is sub menu corresponding to the functional operation of the main menu. Each of the
menus is representative of the specific features of the lamp. The specific contents shows as the table
menu below.
Set or browse lighting function, press UP or DOWN button.
Press ENTER to save your changes or enter the submenu.Press the UP or DOWN can change the nume-
rical (increase or decrease in value).
Press the MODE button to return to menu. Set a time 0 to 10 minutes automatically exit menu interface
and close the screen.
Put through power supply, open the power switch of lamps and lanterns, display show the company
website. According to the main interface, as shown in figure:
In the main interface, press "MODE" button to view the software version, press the "UP" "DOWN" can m-
odify the DMX address.
LOGO
- 9 -
Click on the main interface of the icon, numerical to view view Settings related information of lamps and
lanterns.Symbols such as the main interface appear “ “,the following error message indicates that there
might be a lamps and lanterns,can click to view and control information content to modify the lamps and
lanterns.
CODE #
ERRO INFO CHECK MEASURMENT NOTE
E02 Program Err 1 Check the welding of Chip
E04 MBDInit Error Check the communication signal 485& 485 chip & memory IC
E05 BD1Init Error
E06 BD2Init Error
E12 Bus1 Error Check main cable ABAB（485） chip
E16 MFpga Error
E17 BD1 BUS Error
E18 BD2 BUS Error
E21 Pan FB. Error
E23 Tilt FB. Error
E22 Pan Zero Error
E24 Tilt Zero Error
E36 Zoom RT. Error
E46 H.Fan Error Check the fan of head
E057 EthMDL Error Check the fan of ArtNet、communication signal
RESET
ERROR
Check main cable ABAB（485） chip
Check the communication signal& welding of communication chip
Check the light coupling line, optical coupling switch and a plate of the
relative position measurement
Check cable of sensor, distance and location of ,magnets and sensor

- 10 -
7.3 Menu list
DMX Address 001-XXX
Standard * 1-22
Easy 1-16
Fixture Id 0001-XXXX
Hold
Close *
Static
Program 1
Program 2
Program 3
Resettable xxxxH xxM Clear
Total xxxxH xxM
Error List
DMX Values
DMX Diagnosis
System Information
Pan Invert ON/OFF * Defaul：OFF
Tilt Invert ON/OFF * Defaul：OFF
Feedback ON */OFF Defaul：ON
Liner *
S Curve
Inv SQ
Square
OFF
1 Min.
2 Min. *
5 Min.
10 Min.
Auto Screen ON/OFF
Auto *
High
Silenve
Auto *
DMX
Static
Program 1
Program 2
Program 3
English *
中文
Defaul:2 Min.
Defaul:Liner
Fan Mode
Personality
Default：Standard
Address
Channel Mode
ON DMX
Defaul:English
Screen Time
Language
Default：Close
Fixture Times
Dim.Curve
Boot Mode
Information

- 11 -
Test Sequence Run/Stop
Alone
Master
Slave
Pan 0-255
Tilt 0-255
ZOOM 0-255
Colour 0-255
R 0-255
G 0-255
B 0-255
W 0-255
Strobe 0-255
Dimmer 0-255
Step 1-30
Capture DMX Stop/Run
Reset Reset Step/Reset Prg
Fade Time 0-999
Hold Time 0-999
Pan 0-255
Tilt 0-255
ZOOM 0-255
Colour 0-255
R 0-255
G 0-255
B 0-255
W 0-255
Dimmer 0-255
Strobe 0-255
Program 2 (See above)
Program 3 (See above)
Program 1
Program 2
Program 3
Reset Pan/Tilt/Zoom
Pan
Tilt
Zoom
Factory Default
Stand-AloneService
Calibrations Input Password:****
M/S
Static Mode
Program Play
Program Edit
Program 1

- 12 -
8.DMX protocol
8.1 Unit model
Mode1 Mode2 Dmx Value Function Fade Type
1 1 Pan Pan movement by 450° 0-255
2 2 Pan Fine Fine control of pan movement 0-255
3 3 Tilt Tilt movement by 228° 0-255
4 4 Tilt fine Fine control of tilt movement 0-255
Standard mode 0
Max. Speed Mode 1
Speed from max. to min 2-255
Time from 0.2 sec. to 25.5 sec 2-255
Reserved 0-19
Display ON 20-24
Display OFF 25-29
RGBW colour mixing mode 30-34
CMY colour mixing mode 35-39
Pan/Tilt speed mode 40-44
Pan/Tilt time mode 45-49
Blackout while pan/tilt moving 50-54
Disabled blackout while pan/tilt moving 55-59
Dimmer curve - square law 60-64
Dimmer curve - linear 65-69
Fans mode: Auto 70-74
Fans mode: High 75-79
White point 8000K ON 80-84
White point 8000K OFF 85-89
Fans mode: Quiet 90-94
Reserved 95-129
Reserved 130-139
Pan/Tilt reset 140-149
Zoom reset 150-159
Reserved 160-169
Tungsten effect simulation (750W) On 170-171
Tungsten effect simulation (1000W) On 172-173
Tungsten effect simulation (1200W) On 174-175
Tungsten effect simulation (2000W) On 176-177
Tungsten effect simulation (2500W) On 178-179
Tungsten effect simulation Off 180-181
Reserved 182-255
No function (0=default) 0
Filter 4 (Medium Bastard Amber) 1-2
Virtual colour
wheel
77
Pan/Tilt speed mode
Pan/Tilt time mode
5 5 Pan/Tilt Speed
Pan/Tilt Time
6 6 Power/Special
Functions
To activate following functions, stop in DMX value for at least 3 s
and shutter must be closed at least 3 sec.(Shutter,Strobe)
channel 20/15 must be at range: 0-31 DMX). Corresponding menu
items are temporarily overriden
To activate following functions, stop in DMX value for at least 3 seconds.
Tungsten effect simulution for whites 2700K and 3200K

- 13 -
Filter 25 (Sunset Red) 3-4
Filter 19 (Fire) 5-6
Filter 26 (Bright Red) 7-8
Filter 58 (Lavender) 9-10
Filter 68 (Sky Blue) 11-12
Filter 36 (Medium Pink) 13-14
Filter 89 (Moss Green) 15-16
Filter 88 (Lime Green) 17-18
Filter 90 (Dark Yellow Green) 19-20
Filter 49 (Medium Purple) 21-22
Filter 52 (Light Lavender) 23-24
Filter 102 (Light Amber) 25-26
Filter 103 (Straw) 27-28
Filter 140 (Summer Blue) 29-30
Filter 124 (Dark Green) 31-32
Filter 106 (Primary Red) 33-34
Filter 111 (Dark Pink) 35-36
Filter 115 (Peacock Blue) 37-38
Filter 126 (Mauve) 39-40
Filter 117 (Steel Blue) 41-42
Filter 118 (Light Blue) 43-44
Filter 122 (Fern Green) 45-46
Filter 182 (Light Red) 47-48
Filter 121 (Filter Green) 49-50
Filter 128 (Bright Pink) 51-52
Filter 131 (Marine Blue) 53-54
Filter 132 (Medium Blue) 55-56
Filter 134 (Golden Amber) 57-58
Filter 135 (Deep Golden Amber) 59-60
Filter 136 (Pale Lavender) 61-62
Filter 137 (Special Lavender) 63-64
Filter 138 (Pale Green) 65-66
Filter 798 (Chrysalis Pink) 67-68
Filter 141 (Bright Blue) 69-70
Filter 147 (Apricot) 71-72
Filter 148 (Bright Rose) 73-74
Filter 152 (Pale Gold) 75-76
Filter 154 (Pale Rose) 77-78
Filter 157 (Pink) 79-80
Filter 143 (Pale Navy Blue) 81-82
Filter 162 (Bastard Amber) 83-84
Filter 164 (Flame Red) 85-86
Filter 165 (Daylight Blue) 87-88
Filter 169 (Lilac Tint) 89-90
Filter 170 (Deep Lavender) 91-92
Filter 172 (Lagoon Blue) 93-94
Filter 194 (Surprise Pink) 95-96
Filter 180 (Dark Lavender) 97-98
Filter 181 (Congo Blue) 99-100
Virtual colour
wheel
77
Mode1 Mode2 Dmx Value Function Fade Type

- 14 -
Filter 197 (Alice Blue) 101-102
Filter 201 (Full C.T. Blue) 103-104
Filter 202 (Half C.T. Blue) 105-106
Filter 203 (Quarter C.T. Blue) 107-108
Filter 204 (Full C.T. Orange) 109-110
Filter 219 (Fluorescent Green) 111-112
Filter 206 (Quarter C.T. Orange) 113-114
Filter 247 (Filter Minus Green) 115-116
Filter 248 (Half Minus Green) 117-118
Filter 281 (Three Quarter C.T. Blue) 119-120
Filter 285 (Three Quarter C.T. Orange) 121-122
Filter 352 (Glacier Blue) 123-124
Filter 353 (Lighter Blue) 125-126
Filter 507 (Madge) 127-128
Filter 778 (Millennium Gold) 129-130
Filter 793 (Vanity Fair) 131-132
Raw DMX 133-235
Rainbow effect (with fade time) from slow-> fast 236-245
Rainbow effect (without fade time) from slow-> fast 246-255
8 8
Red/Cyan Colour saturation control - coarse 0-100% 0-255
9 Red/Cyan fine Colour saturation control - fine 0-255
10 9 Green/Magenta Colour saturation control - coarse 0-100% 0-255
11 Green/Magenta fine Colour saturation control - fine 0-255
12 10 Blue/Yellow Colour saturation control - coarse 0-100% 0-255
13 Blue/Yellow fine Colour saturation control - fine 0-255
Colour saturation control - coarse 0-100% 0-255
No function 0-255
15 Whitefine Colour saturation control - fine 0-255
8000K 0
5600K 64
4200K 128
3200K 192
2700K 255
Colour temperature correction for from cool white to 2700K 0-255
Virtual colors ("Virtual" has priority) 0-9
Maximum mode (highest values have priority) 10-19
Minimum mode (lowest values have priority) 20-29
Multiply mode (multiply Virtual and Colour Mix) 30-39
Virtual colour wheel77
12 CTC
If function "White Point 8000K" is ON
To get colour temperatures stated above, RGBW channels have to
be set at the same value e.g. 255DMX (0=default)
To activate Tungsten effect at 2700K and 3200K , set DMX value at
"Power/Special functions" channel)
If function "White Point 8000K" is OFF
16
Colour Mix control
Defines relation between colour channels
"Virtual" = Virtual Colours (Virtual Colour Wheel)
"Colour mix" = Colour channels (RGBW/CMY)
1317
14 11 White
If RGBW mode is selected:
If CMY mode is selected:
Mode1 Mode2 Dmx Value Function Fade Type

- 15 -
Addition mode (Virtual + Colour mix) (45=default) 40-49
Subtraction mode (Virtual – Colour mix) 50-59
Inverted Subtraction mode (Virtual – Colour mix) 60-69
Reserved 70-128
Virtual colors (virtual has priority) 129
Crossfade (crossfade between Virtual and Colour mix) 130-254
Colour channels ("Colour mix" has priority) 255
18 14 Zoom Zoom from max. to min.beam angle (128=default) 0-255
19 Zoom - fine Fine zooming (0=default) 0-255
Shutter closed 0-31
Shutter open (32=default) 32-63
Strobe-effect from slow to fast 64-95
Shutter open 96-127
Opening pulse in sequences from slow to fast 128-143
Closing pulse in sequences from fast to slow 144-159
Shutter open 160-191
Random strobe-effect from slow to fast 192-223
Shutter open 224-255
21 16
Dimmer Dimmer intensity from 0% to 100% 0-255
22 Dimme - fine Fine dimming 0-255
17
20 15 Shutter/ strobe
Colour Mix control13
Mode1 Mode2 Dmx Value Function Fade Type

- 16 -
9.Maintance and cleaning
It is absolutely essential that the fixture is kept clean and that dust,dirt and smoke fluid residues must not
buildup on or within the fixture. Otherwise, the fixtures light-output will be significantly reduced. Regular
cleaning will not only ensure the maximum light-output, but will also allow the fixture to function reliably
through out its life. A soft lint-free cloth moistened with any good glass cleaning fluid is recommended,
under no circum stances should alcohol or solvents be used!
The front objective lens will require weekly cleaning as smoke-fluid tends to building up residues,reduc-
ing the light-output very quickly.The cooling-fans should be cleaned monthly.
The gobos may be cleaned with a soft brush,The interior of the fixture should be cleaned at least annua-
lly usinga vacuum-cleaner or an air-jet.
There are no serviceable parts inside the device except for the lamp and the fuse.
Replacing the fuse: If the lamp burns out,the fine-wire fuse of the device might fuse,too.Only replace the
fuse by a fuse of same type and rating.Before replacing the fuse,unplug mains lead.
Maintenance and maintenance of the operation, please contact the manufacturer or distributor.
DANGER:Disconnect from the mains before starting any maintenance work.
10.1 Electrical paramters
10.Electric equipment specification
SOURCE:
POWER:300
VOLTAGE:
RGBW LED-40W
W
AC100-240V 50/60HZ
Color Temperature:6500K
10.2 Weight and dimensions
Dimensions：250X165X336
NET WEIGHT:5.8Kg
Dimensions
WEIGHT
mm
（Carton Package）: mm
(Carton Package) : Kg
445X360X270
7.2
10.3 Channel Characteristics
．
and network control mo de optional.
2．450 228 Fixture could auto reset.
3．Demme r: lime ar dimme r.
5．Zoom: linear amp lifier.。
6． Shutter: electronic shutter, random strobe.
7．The netwo rk control mo de and DMX control mode have independent control and combined control.
1 22、16 two standard DMX channel mo del
Scan: Pa n °,Tilt °,