Joy-it BUMP-SENSOR User manual

Joy-IT powered by SIMAC Electronics GmbH - Pascalstr. 8 - 47506 Neukirchen-Vluyn - www.joy-it.net
BUMP-SENSOR
SEN-BUMP01

BUMP-SENSOR
SEN-BUMP01
1. GENERAL INFORMATION
Dear customer,
thank you very much for choosing our product.
In the following, we will introduce you to what to observe while starting
up and using this product.
Should you encounter any unexpected problems during use, please do
not hesitate to contact us.

2. DEVICE OVERVIEW
When the switch is not activated, a HIGH level is present at the signal pin.
When the switch is activated, a LOW level is present at the signal pin and
the LED on the board lights up red.
PowerSupply -
PowerSupply +
Signal

3. USE WITH ARDUINO
Wiring
Connect the sensor to your Arduino as shown in the diagram and table
below.
BUMP-Sensor Arduino
GND GND
VCC 5 V
OUT 2

Example Code
In this code example, the status of the sensor is read out every second
and displayed in the serial monitor.
const int SWITCH_PIN = 2;
bool switchState = HIGH; //Variable the switch status
void setup() {
// Initialize the switch pin as an input
pinMode(SWITCH_PIN, INPUT);
// Initialize serial communication at 9600 bps:
Serial.begin(9600);
}
void loop() {
// Read the state of the switch value:
switchState = digitalRead(SWITCH_PIN);
// Read the state of the switch
if (switchState == LOW) {
Serial.println("Switch is pressed!");
} else {
Serial.println("Switch is not pressed!");
}
// Wait for a short period before reading again
delay(1000);
}

4. USE WITH RASPBERRY PI
Wiring
Connect the sensor to your Raspberry Pi as shown in the diagram and
table below.
BUMP-Sensor Raspberry Pi
GND GND (Pin 6)
VCC 3V3 (Pin 1)
OUT GPIO17 (Pin 11)

Example Code
In this code example, the status of the sensor is read out every second
and displayed in the console.
import RPi.GPIO as GPIO
import time
# Define the GPIO pin number
SWITCH_PIN =17
# Setup GPIO mode
GPIO.setmode(GPIO.BCM)
# Setup the GPIO pin as input with a pull-up resistor
GPIO.setup(SWITCH_PIN, GPIO.IN, pull_up_down=GPIO.PUD_UP)
try:
while True:
# Read the state of the switch
switch_state =GPIO.input(SWITCH_PIN)
# Check switch state
if switch_state == 0:
print("Switch is pressed!")
else:
print("Switch is not pressed!")
# Wait for a short period before reading again
time.sleep(1)
except KeyboardInterrupt:
# Cleanup the GPIO settings when the script is terminated
GPIO.cleanup()

Published: 20.09.2023
www.joy-it.net
SIMAC Electronics GmbH
Pascalstr. 8, 47506 Neukirchen-Vluyn
5. ADDITIONAL INFORMATION
Our information and take-back obligations according to the Electrical and
Electronic Equipment Act (ElektroG)
Symbol on electrical and electronic equipment:
This crossed-out dustbin means that electrical and electronic appliances do not
belong in the household waste. You must return the old appliances to a
collection point.
Before handing over waste batteries and accumulators that are not
enclosed by waste equipment must be separated from it.
Return options:
As an end user, you can return your old device (which essentially fulfills the same
function as the new device purchased from us) free of charge for disposal when
you purchase a new device.
Small appliances with no external dimensions greater than 25 cm can be dis-
posed of in normal household quantities independently of the
purchase of a new appliance.
Possibility of return at our company location during opening hours:
SIMAC Electronics GmbH, Pascalstr. 8, D-47506 Neukirchen-Vluyn,
Germany
Possibility of return in your area:
We will send you a parcel stamp with which you can return the device to us free
of charge. Please contact us by email at [e-mail] or by telephone.
Information on packaging:
If you do not have suitable packaging material or do not wish to use your own,
please contact us and we will send you suitable packaging.
6. SUPPORT
If there are still any issues pending or problems arising aer your purcha-
se, we will support you by e-mail, telephone and with our ticket support
system.
Email: [e-mail]
Ticket system: http://support.joy-it.net
Telephone: [phone] (Mon - Thur: 10:00 - 17:00 o‘clock,
Fri: 10:00 - 14:30 o‘clock)
For further information please visit our website:
www.joy-it.net