Jumper mini3 User manual

mini3 User Manual

1 Safety Notices.............................................................................1
2 Device Overview .........................................................................2
3 Basic Operation...........................................................................4
3.1 Boot................................................................................4
3.2 Shutdown .......................................................................5
3.3 Standby..........................................................................5
3.4 Restart............................................................................5
3.5 Install SIM card and TF card ...........................................5
3.6 Connect Network ............................................................6
3.7 Connect to Bluetooth devices..........................................7

1
1 Safety Notices
①Avoid dropping the unit on the ground or by other strong impact.
②Do not use in extreme cold, heat (<35 ℃), excessively humid,
dusty environment, long-term use, do not let the machine in the sun.
③Try to avoid using in magnetic, strong electrostatic environment.
④Once water or other liquids to spill on the unit, should be
immediately shut down, the unit wipe dry before use.
⑤Do not use any cleaner or other liquid containing chemical
ingredients to clean the machine to avoid corrosion and moisture
damage, if absolutely necessary cleaning, use a soft, dry cloth or
paper towel.
⑥The company's hardware and software were non-normal
operation, the machine repair or other data loss resulting from
unforeseen circumstances or delete is not responsible for, nor bear
the losses caused.
⑦When using the file card of T-Flash, do not remove the card to
avoid damage to the memory card or device.
⑧Please feel free to back up your important data to avoid loss.
⑨Do not disassemble the unit, otherwise it will lose warranty rights.
⑩Manual and related software updates at any time without notice,
and Quick Start Guide found discrepancies, please prevail in kind.

2
2 Device Overview

3
1) USB Interface: USB interface can read and write U disk /
removable hard disk and other equipment data.
2) Headphone jack: You can connect a 3.5mm stereo headset.

4
3) Front camera: You can take pictures and video.
4) Handset: Can be used for voice calls.
5) Volume up key: Press this button to increase the volume.
6) Volume down key: Press this button to decrease the volume.
7) Power button: You can use the power button to achieve on /
off and sleep wake up the computer.
8) Reset button: Press this button to restart the machine.
9) TF deck: Support Micro SD, maximum capacity to 32GB.
10) Rear camera: You can take pictures and video.
11) Flash Light：Fill in the light in a darker environment.
12) SIM card slot: support at the same time insert two standard
SIM card.
13) Speakers：Built-in speakers allow you to hear the sound
without linking extra equipment.
3 Basic Operation
3.1 Boot
Press the On / Off button 3-5 seconds and release the seed.
(Note: There is no response when you press the power button, the
device may need to recharge).

5
3.2 Shutdown
①Press and hold for 4 seconds to enter the shutdown screen, and
then click Shut Down.
②Press for 10 seconds to force shutdown.
3.3 Standby
In the power-on state Short press the power button to enter standby
or wakes up from standby.
3.4 Restart
Press and hold for 4 seconds to enter the shutdown screen, and
then click Restart.
3.5 Install SIM card and TF card
Install SIM card
1) When installing the SIM card, the board must be turned off first.
2) Then in the back of the tablet, the upper right corner of the
position, open the SIM deck and TF deck cover.
3) Insert a standard SIM card into the SIM card slot in the direction
shown below.
4) Finally press the boot button to start using the phone card to call
and the Internet.

6
Insert TF Card
Insert the TF card slot in the direction shown in the image below.
Then you can read the contents of the TF card .Support insert or
remove.
3.6 Connect Network
1) In the main menu or interface, choose setting application
procedure.
2) Click WLAN, open wifi, MID will automatically search the available
Wifi wireless internet.

7
3) Choose the Wi-Fi internet you want to connect, if it has password,
it will popup the password window, enter password, click connect.
After you're connected, you're ready to set up email, browse the
web, and do a whole lot more online.
If Wi-Fi isn't available, or you just want the assurance of a wired
connection.
3.7 Connect to Bluetooth devices
Bluetooth function operation
1. Click setting application in main menu interface
2. Click bluetooth and open it.
3. If somebody open bluetooth in your surroundings, click search
device in right above, then MID will automatically search the

8
bluetooth device nearby.
4. Click the available Bluetooth device, it will popup request window,
enter into related password, and match the device to connect.
5. After match successfully, choose the operation you want to.