Jumpking 12ft x 17ft Rectangle Combo User manual

12ft x 17ft Rectangle Combo
User Guide
WARNING: Read these assembly instructions carefully
before attempting to assemble or use this product. Keep
this user guide in a safe place for future reference.
Got a Problem building your trampoline?
Call us on 0344 800 4060 and we can help
Patent no: DE602006006495D1, EP1721640B1 and US7628731
Made In China

IMPORTANT INFORMATION
2
. WARNING! ADULT SUPERVISION & GUIDANCE REQUIRED AT ALL TIMES.
. Recommended age 6+ years.
. No somersaults or flips - can cause serious injury.
WARNINGS!
. Only for domestic use.
. Maximum user weight limit 140 kg.
. Not suitable for children under 36 months - small parts, choking hazard.
. Outdoor use only.
. The trampoline should be assembled by an adult in accordance with assembly instructions
and checked in every instance before use.
. Only one user. Collision hazard.
. Always close the net opening before jumping.
. Remove footwear before jumping on the trampoline.
. Do not use the mat / jumping bed when it is wet.
. Empty pockets and hands before jumping.
. Always jump in the middle off the mat / jumping bed.
. Do not eat whilst jumping.
. Do not exit by a jump.
. Limit the time of continuous usage (make regular stops).
. Do not use in strong wind conditions and sec
. The net should be replaced every 1 year.
ure the trampoline.
ADVISORY
. This trampoline is not intended to be buried in the ground.
. The following product dimension relate to this trampoline:
- Height from ground to top rail: 89 cm (0.89m)
- Height from ground to top of enclosure: 278 cm (2.78m)
- Height from top rail to top of enclosure: 189 cm (1.89m)
. The trampoline must be placed on a level surface at least 2.5m from any structures or
obstructions such as fence, garage, house, overhanging branches, laundry lines or electrical
wires.
. Do not install the trampoline over concrete, asphalt or any other hard surface not at
proximity of other conflicting installation, such as paddling / swimming pools, swings, slides
or climbing frames.
. Inspect the trampoline and the trampoline enclosure net before each use.
Any damaged or worn parts must be replaced before using the trampoline (see parts page 19).
. If an access ladder is used it should be removed when trampoline is not in use.
. Make sure there are no children / animals / obstructions underneath the trampoline.
. Access the trampoline through the door of the enclosure net only. Making sure you securely
close it before bouncing.
. Please don’t use when it’s windy or rainy as this can cause you to slip and become injured.
. Don’t intentionally rebound off the enclosure net as this will weaken it.
. Only attach manufacturer approved accessories to the trampoline and enclosure net.
. Always jump in the middle of the mat and practice bounce techniques safety with adult
supervision and guidance.
. Jump without shoes.
. In certain countries during winter period, the snow load and the very low temperature can
damage the trampoline. It is recommended to remove the snow and store the mat and the
enclosure indoors.

JUMPING INSTRUCTIONS
Fundamental Bounce
1. Start from a standing position with
your head erect and your eyes on the
frame pad.
2. Swing your arms forward and up in a
circular motion.
3. Bring your feet together and point
your toes downward while in the air.
4. Keep your feet about 30 cm (15 in.)
apart from when landing on the bed.
Seat Drop
1. Land in a sitting position with your
legs parallel to the bed.
2. Place your hands on the bed beside
your hips.
3. Push with your hands to return to an
erect position.
Hand and Knee Drop
1. Start bouncing from a standing
position, keeping your eyes on the
frame pad.
2. Land on the bed on your hands and
knees.
3. Push with your hands and come back
up to an erect position.
HalfTurntable
1. Start from the front drop position
and push to the left or right with
your arms to begin turning your body
in the opposite direction.
2. Turn your head and shoulders
toward the direction that your body
is turning.
3. Keep your back parallel to the bed
and your head up.
4. After completing a half turn, land in
the front drop position.
Knee Drop
1. Start bouncing from a standing
position, keeping your eyes on the
frame pad.
2. Land on your knees, keeping your
back straight and your body erect.
3. Come back up to an erect position.
Swivel Hips
1. Start with a seat drop.
2. Turn your head to the left or right
and swing your arms up in the same
direction.
3. Turn your hips in the same direction
as your head and arms, completing a
twist.
4. Land in the seat drop position.
3
IMPORTANT PRECAUTIONS
surface.
1 user allowed at any one time.
This can result in serious injury to head, neck, arms or legs.

4
CARE & MAINTENANCE
Regular care and maintenance of your trampoline is required. This will help prolong its life and reduce
the possibility of injury. Neglecting this can lead to a risk for users.
Inspect your trampoline before each use using the checklist below as a guide. Take particular care in
doing this at the start of each season and at regular intervals. Ensure all parts are in tact and cannot
become dislodged during play, tighten any screws or nuts and bolts where required.
IMPORTANT: If any faults are found, the trampoline MUST NOT BE USED. We advise that the
trampoline is dismantled and placed in a dry place until new parts are
Looking after your trampoline:
Excess weight and improper use will damage it and
cause it to break easily.
Do not use any abrasive cleaners as this could damage the product.
Prolonged exposure to sun
and harsh weather can shorten its life.
Common damage can be caused by water pooling, garden/outdoor debris landing on it, sparks
from nearby or displays landing on it.
their claws can damage it.
A trampoline can act like a sail in strong winds. It can be blown over
which can cause damage to the frame and surrounding areas. We recommend that it is moved
to a sheltered location and secured to the ground, or
dismantled and stored awa
y
.
Follow assembly
instructions in reverse order making sure the springs are removed before dismantling frame.
To be lifted by 2 people. Lift slightly off the ground,
keeping the frame horizontal. Never drag to move it as this can displace parts. Always check that
parts are positioned correctly after moving.
PART
All Parts
Springs
Frame / Enclosure
Poles
Bed / Enclosure
Net / Frame Pad /
Foam Tubes
CHECKLIST
Securely attached
Correctly positioned
No sharp edges or points present
No missing parts
No damage (bent / broken / rusting)
No missing parts
No bent parts
No damage
No rusting or corrosion
No missing parts
(e.g. V-rings / Ties / Zips etc.)
No sagging
No damage
(Holes / Rips / Fraying / Tearing)
NOT OKOK
Use your Trampoline as advised on pages 2-3.
Keep your trampoline clean. If any part becomes dirty, clean with a damp cloth and dry thoroughly.
Store the enclosure net and frame pad in a dry place when not in use.
Keep the bed in good condition by protecting it with a cover.
Keep animals/pets away from the trampoline,
Protect from high winds.
Dismantle and store away in a dry place if not being used for long periods.
Take care when moving the trampoline.

BUILDING YOUR TRAMPOLINE
Description:
Safety glasses
Description:
Cross-head screwdriver
Description:
Mallet
Description:
Gloves
WHAT YOU WILL NEED
1. This is a 2 person build.
2. Time for build is approximately 2 hours.
3. Choose a good location:
(wood chippings, sand or grass).
(7.3m) from ground level, away from
wires, trees and other possible hazards.
(2.5m) around sides, away from walls, fences, structures, tarmac
and other hard surfaces and play areas.
5
Description:
Allen Key

6
PARTS LIST
Part 2
Part 6Part 8
Part 11
Part 16
Part 17
Part 18 Part 19 Part 20
Part 21 Part 22
Part 9
Part 14 Part 15
Part 3
Part 13
Part 12
Part 7Part 10
Part 4Part 5
Part 1
Description:
L-Top tube
D marking
Quantity: 2
Description:
Description:
Stitched bed
Quantity: 1
Description:
Top enclosure poles
Quantity: 8
Description:
Enclosure netting
Quantity: 1
Description:
7inch Springs
Quantity: 144
Description:
Bottom enclosure
poles
Quantity: 8
Description:
Cords
Quantity: 8
Description:
Cap connector
Quantity: 8
Description:
10mm Screws
Quantity: 4
2 pcs pre-assemble
on frame.
Description:
L Legs
Quantity: 8
Description:
Spring tool
Quantity: 1
Description:
Quantity: 24
Description:
Centre legs
Quantity: 4
Frame pad
Quantity: 1
Description:
Black G3 poles
Quantity: 4
2 x Long Sections
2 x Short Sections
Self tapping screws
and spring washers
Description:
Quantity: 2
Description:
Top Tube
D marking
9 spring holes
Quantity: 2
Description:
L-Top tube
A marking
Quantity: 2
Description:
Top tube
2 pcs B 2 pcs C
Quantity:
Description:
T-Connector +
welded tube
2 pcs A 2 pcs B
2 pcs C 2 pcs D
Quantity: 8
4
Description:
Top Tube
D, A marking
10 spring holes
Quantity: 2
Description:
G3 L Steel Connector
(Have been attached to
the G3 poles Part L)
Quantity: 4
Top Tube with
extension
C marking
9 spring holes9 spring holes
4 sections

7
Join Part 4 and Part 5 together.
STEP 1 : ASSEMBLING THE FRAME
You will need the following parts to complete section 1:
2 x Part 1 & 21: L tube with C D marking and
T-Connector + Welded Tube (2xD).
2 x Part 2 & 21: L tube with A B marking and
T-Connector + Welded Tube (2xA).
4 x Part 3 & 21: Top tube with B and C marking and
T-Connector + Welded Tube (2xB 2xC).
2 x Part 4: Straight tube with C marking with extension
(9 spring holes)
2 x Part 5: Straight tube with D marking(9 spring holes)
2 x Part 6: Straight tube D A marking(10 spring holes)
4 x Part 7: Centre Leg
8 x Part 8: L Leg
16 x Part 16: Self tapping screw + washers
21
16
12
L-Top tube
C D marking
L-Top tube
A B marking
Centre leg L Leg
You will also need a cross-head screwdriver
(not supplied).
Self tapping screw and washer
Cross-head screwdriver
4
5
Top tube C marking(9 spring holes)
Top tube D marking(9 spring holes)
8
With D marking
With C marking
Long - 9 spring holes
6
Top tube D A marking(10 spring holes)
7
Top tube C marking with extension (9 spring holes) Top tube D marking(9 spring holes)
With A marking
With B marking
Long - 9 spring holes
Please note: The Welded tube faces inwards on the frame
Top tube B marking and C marking(9 spring holes)
3
T-Connector + Welded tube
Place Part 1 - L Tube upside down and attach Part 21 - T-Connector + welded tube D marking to the long end,
join Part 3 - Top tube C marking (9 spring holes) to the short end and attach Part 21 - T-Connector + welded tube
C marking.
N.B: The welded tube is to be positioned on the inside of the frame and screw holes facing towards one another.
Place Part 2 - L Tube upside down and attach Part 21 - T-Connector + welded tube A markingto the long end,
join Part 3 - Top Tube B marking (9 spring holes) to the short end and attach Part 21 - T-Connector + welded tube
B marking.
Screw together Part 7 - Centre leg and Part 8 - L Leg to make your leg sections.
As shown in image above.

8
Push down on the end of the centre leg to fully
rt the L Leg into the T-Connector.esni
You have now completed the frame section.
Repeat the last two steps until you have assembled the remaining sections of the trampoline
frame.
You have now completed step 1.
Screw one of the self tapping screws through the
hole in the T-Connector and into the hole in
the leg extension using the cross-head screwdriver.
With D marking
With C ma
A marking
A marking
B marking
B marking
rking
D marking
D marking
C marking
C marking
Top tube D marking
9 spring holes
Top tube C marking
9 spring holes
Top tube C marking
9 spring holes
Top tube D marking
9 spring holes
Tighten with 10mm screws
Note: You may need to tap the L Leg in using a rubber mallet
or by placing a piece of wood over the top of the tube. Do not
use a metal hammer on the metal tube as this may distort
the end of the tube.
Using Part 20 tighten the 10mm screws to secure the two top rails together - Part 4 and 5.
Important: The frame is held together under tension, so
you may need to use some force to insert certain parts.
Place your feet on the top tubes and grip the L Leg with
both hands.
Pull the L Leg unil it can be slotted into the T-Connector.
Slot the end of the L Leg into the T-Connector.

9
This step will require 2 people who must be
wearing gloves.
Slot two of the frame section together as shown in
the diagram.
You will now need to slot the frame together, this
will take some force. The easiest method is if the
two people face each other.
Important:
Numbers relate to amount of
spring holes on top rail.
Ensure all of the top tubes, L legs
and centre legs are fully inserted.
The frame is now fully assembled and you have
now completed step 2.
Hold the top tubes either side of the
T-Connector+welded tubes and push
towards each other until the loose end of the
frame can be inserted into the T-connector.
STEP 2 : ASSEMBLING THE FRAME
Attach Part 6: Top tube with A D markings (10
spring holes) in between the T-connector+welded
tube marked A and D. Repeat this to have two halves.
Take the joined Part 4 and 5 top tubes and join the
two halves ensuring the black bolt covers are on
the inside of the frame (facing inwards).
Please ensure the black bolt covers are on the
inside of the frame.
Note: The long side will bow outwards.
With A
marking
A13
A13
B9
With B marking
B9
D9 C9
With C marking
C9
C9
C9
D9
With D
marking
AD10
D13
AD10
D13
With C marking
With B marking
With A
marking
With D
marking

10
STEP 3 : FITTING THE STITCHED BED
This step will require 2 people who must be
wearing gloves and protective eye wear.
Lay the stitched bed (with the V-Rings) out, inside
the frame of the trampoline with the warning labels
facing upwards.
Please note the bed is 2 foot smaller than the frame.
Locate the 4 corner V-rings.
Slot one of the springs onto one of the V-rings
as shown.
Important: springs must be slotted on the right way
around with the more curled end of the spring
hooked into the V-ring.
Slot the other end of the spring into one of the
spring holes on the top of the frame.
IMPORTANT: Ensure the spring is fully
inserted into the slot on the top of the frame.
Part 10
Part 9
Please see page 11 for detailed spring attachment

11
Attach a spring to the diagonal V-ring.
Important: You will now need to use the spring
tool to attach the spring to the frame.
Hook the spring tool onto end of spring, and pull
until the spring can be slotted into the spring slot
on the top of the frame.
IMPORTANT: Ensure the spring is fully
inserted into the slot on the top of the frame.
T-connector+welded tube
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17 18
Attach the springs in the sequence shown.
Starting at point 1-4 - Attach 5 Springs to the corner sections.
Continue following the sequence 5-18 keeping the tension even.
Note: The long side of the frame bows outwards until springs pull the fame inwards.
The stitched bed is now fitted and you have completed step 3.
Sleeve

12
STEP 4 : FITTING THE FRAME PAD
This step will require 2 people.
Lay the frame pad - Part 11 out over the edge of
the frame with the ties facing downwards.
Align the openings in the frame pad with the
T-connector+welded tube's on the frame.
The frame pad is now and you have
completed step 4.
WARNING: The trampoline MUST NOT be used
during construction.
ABC
Frame Pad Frame Pad
Frame Pad
Top tube
Top tube
Top tube
Webbing Webbing Webbing
D-ring D-ring
D-ring
Look under the trampoline and locate the pairs
of straps near the edge of bed(10) and loop the
See the inset drawing. A, B and C. Repeat this
step with the remaining straps (not shown).
Please note the pad comes in 4 sections.
straps through the D-rings fastening to the
frame.

STEP 5 : FITTING THE ENCLOSURE TUBES
You will need the following parts to complete step 5:
8 x Top enclosure tubes
- Part 12
8 x Bottom enclosure tubes
- Part 13
8 x Self tapping screws & washers -- Part 16
You will also need a cross-head screwdriver (not
supplied).
Slot the thin end of one of the bottom enclosure
tubes into the open end of one of the top
enclosure tubes.
Align the screw hole in the bottom enclosure pole
with the screw hole in the top enclosure pole.
Screw one of the self tapping screws through the
hole in the top enclosure pole and into the hole in
the bottom enclosure pole using the cross-head
screwdriver.
Please note the screw is larger than the hole.
Some force will be needed to screw this in.
Top enclosure tube
Bottom enclosure tube
Self tapping screw and washer
Cross-head screwdriver
13

14
Slot the bottom enclosure pole into the welded tube
attached to the T-Connector. These are visible through
the slots in the frame pad.
Assemble the remaining seven enclosure tubes
using the self tapping screws and the
cross-head screwdriver.
Slot the remaining seven enclosure tubes into the
T-connector+welded tube's on the frame.
The enclosure tubes are now and you have
completed step 5.
Screw one of the self tapping screws through the slot
in the tubing and into hole using the cross-head
screwdriver.

STEP 6 : FITTING THE ENCLOSURE NETTING
You will need the following parts to complete step 6:
1 x Enclosure netting - Part 15
Lay the enclosure netting out on the trampoline.
Enclosure
netting
15
2 x Black G3 poles
(2 x Long Sections, 2 x Short Sections)
- Part 14
Find the sleeves that run along the top of the
enclosure netting.
Slot the thin sections on the two black G3 poles
into the metal ends so the poles become two long
sections.
Black G3
poles
You may need to slide the connected poles around
in the nettings sleeves until the thin black sections
are aligned with the gaps between sleeves.
Connect the 4 Corner Connectors - Part 22 to
the G3 Poles.
Please Note: The corner connectors will sit in a
larger gap in the netting.
The zip of the door is on the long side of the
trampoline.
insert one of the exposed sections of the Black
G3 pole into a plastic grip on top of one of the
enclosure tubes.
With the netting hanging on the inside of the
enclosure poles, stand on the trampoline and
4 x G3 Connectors - Part 22

Attach the seven other exposed sections of the
G3 rods to the other enclosure tubes in the
order shown in the diagram.
Ensuring the four corners of the G3 rods are
in the exposed sections.
The enclosure net is now and you have
completed step 6.
16
4
5
6
78

17
STEP 7 : ATTACHING THE BOTTOM OF THE NET
You will need the following parts to complete step 7:
8 x Cords
- Part 17. .
Tie one end of the cord around a V-ring on the bed
of the trampoline. Push the outer end through a
hole in the bottom of the netting. Sew in and out
using every V-ring and hole in the netting nearest
to that V-ring.
Important: Keep the cord tight at all times.
Continue to do this until all the net is sewn in,
tying off the rope and starting the next when it has
come to the end.
From the underside of the trampoline, tie the
remaining elastic straps around the springs or
through the V-Rings.
You have completed step 7 and the trampoline is
fully assembled.

USING THE TRAMPOLINE
To enter the trampoline, unzip the door and climb
in.
Always close the doorway before using the
N.B.: The zip will be on the long side of the
trampoline.
trampoline.
Ensure that there is 7.3 metres (24 feet) clearance
above the trampoline.
Also check that there are no overhanging objects
in the area above the trampoline.
7.3m
24ft
Door
zip
18
2.5m
8.2ft
Before using your trampoline, check again that
there is enough clearance around it. Maintain a
clear space of 2.5 metres (8.2 feet) on all sides of
the trampoline.
Also check that the area is free from walls,
structures, fences, tarmac and any other hard
surfaces and other play areas.

SPARE PARTS
For a full range of accessories and replacement parts call 0344 800 4060
or visit our web site at: www.jumpking.eu
Customer Helpline on: 0344 800 4060.
To help us assist you, please provide the following information when calling:
12’ x 17’ Rectangle Combo
(see parts list below).
19
To order replacement parts, you can email us on: [email protected], or call our
17
16
Key
No. Qty. Description
Key
No. Qty. Description
23
14
9
18
7
7
21
21
3
8
8
1
6
7
8
458
10
11
12
13
14
15
5
2
5
19
Welded T-connector
1 2 L Frame with C D marking
2 2
4
L Frame with A B marking
3
1
T-connector+welded tube
(Ax2, Bx2, Cx2, Dx2)
4 2
C marking (9 Spring holes)
5 2 Straight tube with D marking
S
Straight tube with B & C marking
(9 spring holes)
traight tube with extension
(9 spring holes)
6 2 Straight tube with A D marking
(10 spring holes)
7 4 Centre Leg
8 8L Leg
9 144 8.5” springs
10 1 Bed
11 1 Surround pad
12 8 Bottom enclosure poles
13 8 Top curved enclosure poles
14 1 G3 Rod - 4 in pack with connectors
15 1 Net
16 1 Self tapping screws pack of 24
17 1 Ropes - 8 in pack
18 1 Spring tool
19 8 Cap Connector
20 4 10mm Screws
21 8
23 Manual
21