Jung FTR231 User manual

Operating instructions
Floor thermostat
Art. no. FTR231
16.09.2022
82404903 J0082404903
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Schalksmühle
GERMANY
Telefon: [phone]
Telefax: [phone]
[email protected]
www.jung.de

Table of Contents
1 Safety instructions.............................................................................................................3
2 Device components...........................................................................................................3
3 Intended use .....................................................................................................................3
4 Product characteristics......................................................................................................4
5 Functional description .......................................................................................................4
6 Operation ..........................................................................................................................4
7 Information for electrically skilled persons ........................................................................5
7.1 Commissioning ...................................................................................................... 7
8 Technical data...................................................................................................................8
9 Warranty............................................................................................................................9
2 / 9
82404903 16.09.2022
J0082404903
Floor thermostat

1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled
persons.
Serious injuries, fire or property damage possible. Please read and follow manual
fully.
Danger of electric shock. Always disconnect before carrying out work on the device
or load. In so doing, take all the circuit breakers into account, which support danger-
ous voltages to the device and or load.
Danger of electric shock. The sensor cable is connected to the mains voltage poten-
tial. If the sensor cable is damaged, immediately disconnect the device from the
mains by switching off all associated circuit breakers.
This manual is an integral part of the product, and must remain with the end cus-
tomer.
2 Device components
Image1: Device components
(1) Room temperature controller insert
(2) Frame
(3) Status LED
(4) Central plate
(5) Control knob
(6) Adjustment rings for temperature limit
3 Intended use
– Electronic temperature controller for controlling electric underfloor heating or
floor temperature conditioning systems
– Control of the floor temperature in closed rooms
– Mounting in appliance box with dimensions according to DIN 49073
Floor thermostat
3 / 9
82404903 16.09.2022
J0082404903

4 Product characteristics
– Manually setting a comfort temperature for the floor
– Manually switching off the temperature control
– Input terminal for activation of reduction temperature (ECO) via central clock
– External temperature sensor (remote sensor)
– Frost protection function
– Controller output working method: pulse width modulation (PWM) or two-point
switchable
– Interruption of heating for 5 minutes after one hour in continuous heating mode
– Permanent LED operation possible
5 Functional description
ECO operation
In many areas of the building it makes sense for the temperature to be set to a lower
ECO temperature at certain times rather than to heat permanently to the comfort tem-
perature. By connecting the input terminal Ø to 230 V, the temperature is reduced by
4 °C and the status LED lights up green. This should be controlled by a central clock.
Controller adaptation
Depending on the heating system, the control behaviour can be adjusted.
Pulse width modulated control (factory setting): The output is not permanently actu-
ated, but for a time period (pulse width) that depends on the difference between tar-
get and actual temperature. This method brings the actual temperature gradually
closer to the target temperature.
Two-point control: The output remains switched on until the selected target temperat-
ure has been exceeded by 0.5 °C. The output will not be switched on again until the
target value is undercut by 0.5 °C. Since most heating systems respond very slowly,
this type of control can entail temperature overshooting.
6 Operation
Increasing or reducing the floor temperature
￭ Turn the control knob to the right or left.
If the target temperature is not reached, the LED lights up red for a maximum
of 2 minutes (green = ECO). The indication can also take place during the en-
tire heating process (see Activating/deactivating permanent LED operation).
In the middle position, the device regulates to approx. 30 °C target temperat-
ure. The lowest target temperature is approx. 5 °C and the highest target tem-
perature is approx. 50 °C
Floor thermostat
4 / 9
82404903 16.09.2022
J0082404903

Indication of the current operating mode
￭ Press the control knob briefly.
The LED lights up for 10 seconds in the colour of the current operating mode.
Orange = frost protection, red = heating mode.
Switching off the temperature control
￭ Press the control knob for longer than 2 seconds until the LED lights up or-
ange.
The device has switched to frost protection. The frost protection prevents the
temperature from falling below 5 °C.
Each time the control knob is turned, the LED lights up orange for 10 seconds.
￭ To activate the temperature control, press the control knob again for more
than 2 seconds.
The device switches back to heating mode. The LED lights up red for
10 seconds.
Activating/deactivating permanent LED operation
In permanent operation, the status LED lights up continuously during the active heat-
ing phase.
￭ Press the control knob for longer than 10 seconds until the LED lights up or
flashes in the colour magenta.
LED lights up magenta = permanent operation is active
LED flashes magenta = permanent operation is inactive (default setting)
￭ Press the control knob briefly to switch the mode.
￭ Press the control knob for more than one second to adopt the displayed mode.
After 10 seconds without actuation, the displayed mode is automatically adop-
ted.
7 Information for electrically skilled persons
Remote sensor mounting instructions
The remote sensor must meet the requirements of protection class II and be routed
together with sensor cable S03VV in a protective tube. This protects the remote
sensor from humidity and allows for an easier exchange in the event of repair.
Is the status LED (3) flashes red rapidly, there is an error at the remote
sensor. No temperature measurement, and thus no control, is possible.
If the sensor cable is interrupted or no remote sensor is connected, continuous
heating is carried out. If there is a short circuit of the sensor cable, heating is
not carried out.
Floor thermostat
5 / 9
82404903 16.09.2022
J0082404903

DANGER!
Mortal danger of electric shock.
Disconnect the device. Cover up live parts.
Connecting and fitting the device
Recommended installation height: 1.50 m.
Image2: Connection example of the insert
Image3: Clampable conductor cross-section
(7) External temperature sensor (remote sensor)
(8) Switching contact of central clock
(9) Electric underfloor heating
￭ Connect insert (1) according to the connection diagram (see figure 2). Ob-
serve the conductor cross-sections (see figure 3).
￭ Optionally, connect the ECO operation input Ø via a switching contact of a
central clock (8).
If 230 V is applied to the input, the target temperature is reduced by 4 °C.
Floor thermostat
6 / 9
82404903 16.09.2022
J0082404903

￭ Fit device in appliance box; terminals must be at the bottom.
￭ Fit the frame, central plate and control knob.
￭ Switch on mains voltage.
7.1 Commissioning
Setting control behaviour
Factory setting: pulse width modulated control (PWM)
This setting can be used with most heating systems without adaptation.
Changing the settings
￭ Press the control knob for longer than 20 seconds.
The LED flashes green for PWM control and green/blue for 2-point control.
￭ Press the control knob briefly: The control behaviour is changed.
￭ Press the control knob for longer than one second.
The current control behaviour is saved and the setting mode is exited automat-
ically.
After approx. 2 minutes without any operation the menu is exited without sav-
ing.
Setting the temperature limits
The temperature control has a setting range from 5 to 50 °C. The adjustment rings in
the central plate can be used to limit the temperature setting range.
Floor thermostat
7 / 9
82404903 16.09.2022
J0082404903

Image4: Setting the temperature limit (before/after)
￭ Pull the control knob off the central plate so that the adjustment rings are vis-
ible Bild.
Pulling off is done by hand or with a suitable tool, e.g. vacuum lifting tool or
key cap puller.
￭ Turn the large blue adjustment ring clockwise to the desired minimum temper-
ature. Each notch corresponds to a change of about 2°C.
￭ Turn the small red adjustment ring anticlockwise to the desired maximum tem-
perature.
The respective adjustment ring can only be turned in one direction. To return
to the original setting, continue turning to the respective position.
￭ Replace the control knob, observing the coding (Fig. 4, bottom) of the control
knob and rotary axle.
8 Technical data
Rated voltage AC 220 ... 240 V ~
Floor thermostat
8 / 9
82404903 16.09.2022
J0082404903

Mains frequency 50 / 60 Hz
Switching current 10 A
Connected load
Ohmic load 2300 W
Standby power max. 0.15 W
Ambient temperature -5 ... +45 °C
Storage/transport temperature -25 ... +70 °C
Cable length inputs max. 100 m
Controller class (EU 811/2013) IV
Contribution to energy efficiency 2%
FFNTC remote sensor
Dimensions Ø×H 7.8 × 20 mm
Length connecting cable 4 m (can be extended to 50 m)
Degree of protection IP 67
9 Warranty
The warranty is provided in accordance with statutory requirements via the specialist
trade.
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Schalksmühle
GERMANY
Telefon: [phone]
Telefax: [phone]
[email protected]
www.jung.de
Floor thermostat
9 / 9
82404903 16.09.2022
J0082404903