Juplink Vanin RX4-1500 Wi-Fi6 User manual
Website : www.juplink.com
Before Setting
To customize your wireless network
connection and other advanced repeater
settings, please go to
www.juplink.com/pages/contact-us
to download RX4-1500 updated Firmware
and User Guide for more information.
Operating Conditions
Working Temperature: 0~45°C / 32~113°F
Working Humidity: 10%~90% RH
(No condensation)
Storage Temperature:-40~85°C / -40~185°F
Storage Humidity: 5%~95% RH
(No condensation)
Quick Start Guide-2
V A N I N
RX4-1500
Wi-Fi6 Router
LED Status Indicators
LED indicator
Green LED Indicator
To start the WPS negotiation process of the router
To connect to the wired devices such as computers, switches, ect
To reset the router
Solid on The router is starting to connect or has been successfully connected
to the internet.
Status Description
Description
WPS
RST
The router is performing WPS negotiation
Ports / Buttons
LAN 1. 2. 3. 4
WAN Port
Power
To conncet this router to the internet
To connect to the power cord
Fast blinking
Step 2: Connect Your Router
① Find the SSID (Network Name) Juplink-RX4-1500_5G or
Juplink-RX4-1500 on phone or computer
1. Basic connection - Wirelessly
2. Basic connection - WPS Button
② Click the network icon of your device or go to Wi-Fi Settings of your
smart device, and then select the SSID Juplink-RX4-1500_5G or
Juplink-RX4-1500 to join the network.
Ensure that Mobile Data ( if any ) is disabled.
Note : ① WPS is not supported by iOS devices.
② The WPS function cannot be configured if the wireless function
of the router is disabled. Also, the WPS function will be disabled if
your wireless encryption is WEP. Please make sure the wireless
function is enabled and is configured with the appropriate
encryption before configuring the WPS.
② Within two minutes, press the button on your router.
① Tap the WPS icon on the device’s
Back of your router view
Wireless devices that support WPS, including Android phones, tablets,
and most USB network adapters, can be connected to your router
through this method.
Computer Smart Device
WLAN
Juplink-RX4-1500
Juplink-RX4-1500_5G
WLAN
Juplink-RX4-1500
Juplink-RX4-1500_5G
Step 3: Log In to Your Router Step 4: Set up Internet Connection
POWER WPS 2.4G 5G
POWER WPS 2.4G 5G
POWER WPS 2.4G 5G
POWER WPS 2.4G 5G
Internet
Please ensure that the router has been turned on and connected to the Internet Service Provider(ISP)
① Connect the power adapter to the router’s power port and plug the other end into a power outlet. The LED indicator becomes solid green
② Connect the WAN port of the router to a LAN port of your modem
③ Connect your device to the router.
Modem Apower Outlet
AC-DC Power cord
Ethernet WAN in Front Panel LED Green
Modem LAN out
Step 1: Basic Installation
Juplink-RX4-1500_5G
Juplink-RX4-1500
Juplink Wi-Fi 6 Router
① Lauch a web browser on the device which has been connected
to the repeater,Enter 192.168.0.1 in the address bar to log in.
② Username:admin / Passwrod:admin
③ Click Login Button below
http://192.168.0.1
Login 192.168.0.1 Juplink RX4-1500 router
Username
Password
admin
admin
Cancel Login
Method 1 : Connect to the Internet Automatically
Note: Generally, the addressing type is DHCP. If it is PPPOE,
you need to fill in the username and password which
was provided by your ISP
Please refer to
Method 2: Connect to the Internet - PPPoE
③ Confirm your WiFi name and password and click OK button
④ The router will reboot and you can reconnect by using the new
Wi-Fi Name ( SSID ) and new password in 10 Seconds.
① Select PPPoE type from the Addressing Type drop-down list
② Enter the Username and Password provided by your ISP.
Method 2 : Connect to the Internet - PPPoE
② Set 2.4G /5G SSID ( Wi-Fi Name ) and
2.4G /5G SSID Network Key ( Wi-Fi password ) then click Continue
Step 5: 2.4G Network Setting
① Select Network then select 2.4G setting.
② You can modify your Wi-Fi Name (SSID) , Wi-Fi Password (Key)
Authentication Mode and Encryption Mode
③ After click Apply/Save Button, The router will reboot and you can
reconnected by using the new SSID and New Key (Password)
Step 6: 5G Network Setting
① Select Network then select 5G setting.
② You can modify your Wi-Fi Name (SSID) , Wi-Fi Password (Key)
Authentication Mode and Encryption Mode
③ After click Apply/Save Button, The router will reboot and you can
reconnected by using the new SSID and New Key (Password)
What’s in the Box
1 x Juplink RX4-1500 Router
1 x Ethernet Cable
1 x AC-DC Adapter
1 x Quick Start Guide
Manufacturer’s information
Nanjing Juplink Intelligent Technologies Co.,Ltd.
Address: No. 757 Dixiu Road, Binjiang Economic Development Zone
Jiangning District, Nanjing Technical
Made in China
① Select DHCP type from the Addressing Type drop-down list
② Set 2.4G /5G SSID ( Wi-Fi Name ) and
2.4G /5G SSID Network Key ( Wi-Fi password ) then click Continue
Note: The Default Password Both 2.4G and 5G is: 12345678
Before Setting
To customize your wireless network
connection and other advanced repeater
settings, please go to
https://www.juplink.com/pages/contact-us
to download RX4-1500 updated Firmware
and User Guide for more information.
Operating Conditions
Working Temperature: 0~45°C / 32~113°F
Working Humidity: 10%~90% RH
(No condensation)
Storage Temperature:-40~85°C / -40~185°F
Storage Humidity: 5%~95% RH (No condensation)
Quick Start Guide
V A N I N
RX4-1500
Wi-Fi6 Router
Other Setting
POWER WPS 2.4G 5G
POWER WPS 2.4G 5G
Website : www.juplink.com
Internet
Modem
Ethernet WAN in
Existing Wi-Fi Extended Wi-FiReceive signal
Modem LAN out Repeater Your Wireless Device
Router
Step 2 : Login Web UI
1. Connect your Wi-Fi device to the repeater’s Wi-Fi network
Juplink-RX4-1500_5G or Juplink-RX4-1500.
2. Lauch a web browser on the device which has been connected
to the repeater,Enter 192.168.0.1 in the address bar to log in.
3. Username:admin / Passwrod:admin
Ensure that Mobile Data ( if any ) is disabled.
WLAN
Juplink-RX4-1500
Juplink-RX4-1500_5G
http://192.168.0.1
Login 192.168.0.1” Juplink RX4-1500 router
Username
Password
admin
admin
Cancel Login
1. Click on Application and go to the Repeater interface.
2. Click the Scan WiFi button, Then wait about 5 seconds.
3. Select Enable & Sync with gateway（ suggest ）
Step 3 : Setup Your Repeater 4. Enter the password of the Wi-Fi that will be extended in Key blank
5. Click Connect button
Juplink_RX4-1500_5G
Juplink_RX4-1500_2.4G
2 Repeater Mode - Client
Internet
Modem
Ethernet WAN in PC or other device WAN inRepeater LAN out
Existing Wi-Fi Receive signal
Modem LAN out Reapeater Your DeviceRouter
Follow the instructions to complete the setup of repeater
Connect the LAN port of repeater to the WAN port of wired device
Step 1 : Setup Your Repeater
Step 2 : Connect Your Device
3 AP ( Access Point ) Mode
WLAN
RX4-1500
Internet
Modem
Ethernet WAN in
Modem LAN out Access Control Router Access Point Router
Step 2 : AP mode Connection
Ethernet WAN inEthernet LAN out
1 Repeater Mode
Step 1 : Common Connection
Step 1: AP Mode Setting
Before Installation Please complete the following settings:
1. D isconnecting the WAN port. Connect a device
to your to the Juplink router and launch a web browser.
2. Visit http://192.168.0.1 you are prompted to enter
a username ( admin ) and password ( admin ) .
3. Select Network and click LAN
Manually set IP address as the following format
192.168.0.XXX ( XXX is any number of 2~254)
Then you need to enter this address to log in to the
web UI instead of the default 192.168.0.1
Note:
If the default login credentials do not work, you might have
changed the admin password. If you cannot remember your
new password, you must perform a factory reset to restore the
router to its factory default settings. For more information, see
Restoring a Juplink home router to the factory default settings.
