JVC GY-LS300CHU User manual

.
The illustration here shows how the handle unit and microphone supplied are attached.
The specifications and appearance of this product are subject to changes for further improvement
without prior notice.
Please check the latest version of the INSTRUCTIONS from the following Mobile User Guide. You can
also download the PDF from the Mobile User Guide.
This manual provides a brief explanation on
operating this camera recorder. For detailed
operation methods and camera settings,
please refer to the “INSTRUCTIONS” provided
in the supplied document disc (CD-ROM) or
the following Mobile User Guide.
GY-LS300CHU/GY-LS300CHE
4K MEMORY CARD CAMERA RECORDER
INSTRUCTIONS (BASIC)
.
Mobile User Guide
When you are outside, you can refer to the instructions from your Android phone or iPhone.
http://manual3.jvckenwood.com/pro/mobile/global/
You can view the Mobile User Guide using the browser on your Android phone or iPhone.
IM 1.00 B5A-0579-00
Thank you for purchasing this JVC product.
Before operating this unit, please read the
instructions carefully to ensure the best
possible performance.
In this manual, each model number is
described without the last letter (U/E) which
means the shipping destination.
(U: for USA and Canada, E: for Europe)
Only “U” models (GY-LS300CHU) have been
evaluated by UL.
Please read the following before getting started:
For Customer Use:
Model No.
Serial No.
Enter below the Serial No. which is located
on the body.
Retain this information for future reference.
GY-LS300CHU

.
1. Read these instructions.
2. Keep these instructions.
IMPORTANT SAFEGUARDS
4.
5.
6.
7.
8.
These are general IMPORTANT SAFEGUARDS and certain items may not
apply to all appliances.
3.
FOR USA
9.
10.
11.
12.
13.
For USA-California Only
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate
Material – special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
CAN ICES-3 A / NMB-3 A
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
2IMPORTANT SAFEGUARDS

Safety Precautions
.
CAUTION
FOR USA AND CANADA
CAUTION:
TO REDUCE THE RISK OF
ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR
BACK).
NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
The lightning flash with
arrowhead symbol, within
an equilateral triangle is
intended to alert the user to
the presence of uninsulated
“dangerous voltage” within
the product’s enclosure that
may be of sufficient
magnitude to constitute a
risk of electric shock to
persons.
The exclamation point within
an equilateral triangle is
intended to alert the user to
the presence of important
operating and maintenance
(servicing) instructions in
the literature accompanying
the appliance.
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
.
This device complies with Part 15 of
FCC Rules. Operation is subject to the
following two conditions: (1) This
device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
Changes or modifications not
approved by JVC could void the
user’s authority to operate the
equipment. This equipment has been
tested and found to comply with the
limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference when the equipment is
operated in a commercial
environment.
This equipment generates, uses, and
can radiate radio frequency energy
and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications. Operation of this
equipment in a residential area is
likely to cause harmful interference in
which case the user will be required
to correct the interference at his own
expense.
Safety Precautions 3
Introduction

.
POUR CANADA
RISQUE
D’ELECTROCUTION
NE PAS OUVRIR
CAUTION:
The mains plug shall remain readily
operable.
Remove the mains plug immediately if
the camera functions abnormally.
WARNING:
The battery pack, the camera with
battery installed, and the remote control
with battery installed should not be
exposed to excessive heat such as direct
sunlight, fire or the like.
ATTENTION:
POUR EVITER TOUT RISQUE
D’ELECTROCUTION NE PAS
OUVRIR LE BOITER. AUCUNE
PIECE INTERIEURE N’EST A
REGLER PAR L’UTILISATEUR. SE
REFERER A UN AGENT QUALIFIE
EN CAS DE PROBLEME.
ATTENTION
Le symbole de l’éclair à
l’intérieur d’un triangle
équilatéral est destiné à
alerter l’utilisateur sur la
présence d’une “tension
dangereuse” non isolée dans
le boîtier du produit. Cette
tension est suffisante pour
provoquer l’électrocution de
personnes.
Le point d’exclamation à
l’intérieur d’un triangle
équilatéral est destiné à
alerter l’utilisateur sur la
présence d’opérations
d’entretien importantes au
sujet desquelles des
renseignements se trouvent
dans le manuel
d’instructions.
Ces symboles ne sont
utilisés qu’aux Etats-Unis.
.
WARNING: TO PREVENT FIRE OR
SHOCK HAZARD, DO NOT
EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
AVERTISSEMENT : POUR EVITER
LES RISQUES D’INCENDIE OU
D’ELECTROCUTION, NE PAS
EXPOSER L’APPAREIL A LA
PLUIE NI A L’HUMIDITE.
NOTES:
The rating plate and safety caution are
on the bottom and/or the back of the
main unit.
The serial number plate is on the
bottom of the unit.
The rating information and safety
caution of the AC adapter are on its
upper and lower sides.
REMARQUES :
La plaque d’identification et
l’avertissement de sécurité se trouvent
sous l’appareil et/ou au dos.
La plaque du numéro de série est
située sur la partie inférieure de
l’appareil.
Les informations d’identification et
l’avertissement de sécurité de
l’adaptateur secteur sont situés sur ses
côtés supérieur et inférieur.
Caution on Replaceable lithium
battery
The battery used in this device may
present a fire or chemical burn hazard if
mistreated.
Do not recharge, disassemble, heat
above 100°C (212°F) or incinerate.
Replace battery with Panasonic, Sanyo,
Sony or Maxell CR2025.
Danger of explosion or risk of fire if the
battery is incorrectly replaced.
Dispose of used battery promptly.
Keep away from children.
Do not disassemble and do not dispose
of in fire.
4Safety Precautions
Introduction

.
When the equipment is installed in a
cabinet or on a shelf, make sure that it
has sufficient space on all sides to allow
for ventilation (10 cm (3-15/16") or more
on both sides, on top and at the rear).
Do not block the ventilation holes.
(If the ventilation holes are blocked by a
newspaper, or cloth etc. the heat may not
be able to get out.)
No naked flame sources, such as lighted
candles, should be placed on the
apparatus.
When discarding batteries,
environmental problems must be
considered and the local rules or laws
governing the disposal of these batteries
must be followed strictly.
The apparatus shall not be exposed to
dripping or splashing and that no objects
filled with liquids, such as vases, shall be
placed on the apparatus.
Do not point the lens directly into the
sun. This can cause eye injuries, as well
as lead to the malfunctioning of internal
circuitry. There is also a risk of fire or
electric shock.
CAUTION!
The following notes concern possible
physical damage to this unit and to the
user.
Carrying or holding this unit by the LCD
monitor can result in dropping the unit,
or in a malfunction.
Do not use a tripod on unsteady or
unlevel surfaces. It could tip over,
causing serious damage to the unit.
CAUTION!
Connecting cables (Audio/Video, etc.) to
this unit and leaving it on top of the TV is
not recommended, as tripping on the
cables will cause the unit to fall, resulting
in damage.
.
When using the AC adapter in
areas other than the USA
The provided AC adapter features
automatic voltage selection in the AC
range from 110 V to 240 V.
USING HOUSEHOLD AC PLUG
ADAPTER
In case of connecting the unit’s power
cord to an AC wall outlet other than
American National Standard C73 series
type, use an AC plug adapter called a
“Siemens Plug” as shown.
For this AC plug adapter, please contact
the local dealers in your area.
Remove the AC adapter from the AC
wall outlet when not in use.
Do not leave dust or metal objects
adhered to the AC wall outlet or AC
adapter (power/DC plug).
Plug Adapter
Safety Precautions 5
Introduction

.
IMPORTANT (for owners in the U.K.)
Connection to the mains supply in
the United Kingdom.
DO NOT cut off the mains plug from
this equipment.
If the plug fitted is not suitable for the
power points in your home or the cable is
too short to reach a power point, then
obtain an appropriate safety approved
extension lead or contact the local
dealers in your area.
BE SURE to replace the fuse only with
an identical approved type, as originally
fitted, and to replace the fuse cover.
If nonetheless the mains plug is cut off
be sure to remove the fuse and dispose
of the plug immediately, to avoid possible
shock hazard by inadvertent connection
to the mains supply.
If this product is not supplied fitted with a
mains plug then follow the instructions
given below:
DO NOT make any connection to the
Larger Terminal coded E or Green.
The wires in the mains lead are coloured
in accordance with the following code:
If these colours do not correspond with
the terminal identifications of your plug,
connect as follows:
Blue wire to terminal coded N (Neutral)
or coloured black.
Brown wire to terminal coded L (Live) or
coloured Red.
If in doubt —consult a competent
electrician.
CAUTIONS:
 To prevent shock, do not open the
cabinet. No user serviceable parts
inside.
Refer servicing to qualified personnel.
When you are not using the AC
adapter for a long period of time, it is
recommended that you disconnect the
power cord from AC outlet.
Blue to N
(Neutral) or Black
Brown to L (Live)
or Red
.
FOR EUROPE
This equipment is in conformity with the
provisions and protection requirements of
the corresponding European Directives.
This equipment is designed for professional
video appliances and can be used in the
following environments:
Controlled EMC environment (for
example, purpose-built broadcasting or
recording studio), and rural outdoors
environments.
In order to keep the best performance and
furthermore for electromagnetic
compatibility we recommend to use cables
not exceeding the following lengths:
The inrush current of this apparatus is
7.6 A.
Exclusive
Cable
Exclusive
Cable
Exclusive
Cable
Exclusive
Cable
Coaxial
Cable
Shielded
Cable
Shielded
Cable
Shielded
Cable
Shielded
Cable
DC 1.8 m
1.4 m
1.2 m
1.7 m
2 m
2 m
3 m
1 m
1 m
USB Mini
AV OUT
HDMI
REMOTE
SDI OUT
AUX
HEADPHONE
AUDIO INPUT 1/2
O
Port Cable Length
CAUTION:
Where there are strong electromagnetic
waves or magnetism, for example near a
radio or TV transmitter, transformer,
motor, etc., the picture and the sound
may be disturbed. In such case, please
keep the apparatus away from the
sources of the disturbance.
6Safety Precautions
Introduction

.
WARNING
This is a Class A product. In a domestic
environment this product may cause
radio interference in which case the user
may be required to take adequate
measures.
CAUTION:
To avoid electric
shock or damage to
the unit, first firmly
insert the small end
of the power cord into the AC Adapter
until it is no longer wobbly, and then plug
the larger end of the power cord in to an
AC outlet.
FOR EUROPE
.
The plastics packaging bags may cause
suffocation when they are covered over the
head. Tear them open, and keep them away
from the reach of infants and children by
ensuring that they are disposed of properly.
.
Dear Customer
This apparatus is in conformance with
the valid European directives and
standards regarding electromagnetic
compatibility and electrical safety.
European representative of
JVC KENWOOD Corporation is:
JVC Technical Services Europe GmbH
Konrad-Adenauer-Allee 1-11
61118 Bad Vilbel
Germany
Sehr geehrter Kunde, sehr geehrte
Kundin, dieses Gerät stimmt mit den
gültigen europäischen Richtlinien und
Normen bezüglich elektromagnetischer
Verträglichkeit und elektrischer
Sicherheit überein.
Die europäische Vertretung für die
JVC KENWOOD Corporation ist:
JVC Technical Services Europe GmbH
Konrad-Adenauer-Allee 1-11
61118 Bad Vilbel
Deutschland
.
Manufacturer
3-12,Moriya-cyo,Kanagawa-ku,
Yokohama-shi,
Kanagawa 221-0022,Japan
Importer (EU only)
JVC House
JVC Business Park
12 Priestley Way,London NW2 7BA,
United Kingdom
Safety Precautions 7
Introduction

.
Battery Pack
The supplied battery pack is a lithium-ion
battery. Before using the supplied battery
pack or an optional battery pack, be sure
to read the following cautions:
To avoid hazards
... do not burn.
When transporting, carry the battery in
a plastic bag.
... do not modify or disassemble.
... do not expose the battery to
temperatures exceeding 60°C (140°F),
as this may cause the battery to
overheat, explode or catch fire.
... use only specified chargers.
To prevent damage and prolong
service life
... do not subject to unnecessary shock.
... charge within the temperature range
of 10°C to 30°C (50°F to 86°F). Cooler
temperatures require longer charging
time, or in some cases stop charging
at all. Warmer temperatures prevent
complete charging, or in some cases
stop charging at all.
... store in a cool, dry place. Extended
exposure to high temperatures will
increase natural discharge and
shorten service life.
... keep a 30% battery level (D) if the
battery pack is not to be used for a
long period of time.
... remove from charger or powered unit
when not in use, as some machines
use current even when switched off.
... do not drop or subject to strong
impact.
... do not short-circuit the
terminals. Keep it away
from metallic objects
when not in use.
Terminals
.
Para Brasil
Informação sobre eliminação de
baterias
Este produto não deverá ser eliminado
como lixo doméstico em geral.
Devolva a bateria velha ao comerciante
ou para a rede autorizada, para que seja
devolvida ao fabricante ou importador.
A reciclagem e eliminação de lixo em
uma maneira adequada, ajudarão para
preservar recursos, prevenindo, ao
mesmo tempo, contra efeitos prejudiciais
sobre a nossa saúde e o meio ambiente.
o
Para Retirar a Bateria Recarregável
Pressione botão e puxe a bateria para fora.
.
Empurre
8Safety Precautions
Introduction

Contents
Introduction
Safety Precautions ............................................ 3
Contents ............................................................ 9
Verifying the Accessories .................................. 9
Names of Parts ................................................ 10
Preparations
Attaching the Handle Unit ................................ 13
Attaching the Lens (Commercially Available) .. 13
Adjusting the Grip Belt ..................................... 14
Attaching the Supplied Microphone O ........ 14
Charging the Battery ........................................ 14
Configuring the Initial Settings ......................... 16
Usable Cards ................................................... 17
Estimated Recordable Time of SD Cards ........ 18
Inserting an SD Card ....................................... 18
Shooting
Basic Shooting Procedures ............................. 21
Miscellaneous Functions for Shooting and
Recording Methods ......................................... 22
Playback
Playing Recorded Clips ................................... 23
Connecting External Devices
Connecting External Monitor ........................... 24
Loading Clips to the PC ................................... 25
Network Functions
Functions of Network Connection .................... 26
Others
Menu Screen Hierarchical Chart ..................... 27
Basic Operations in Menu Screen ................... 28
Display Screen ................................................ 29
Status Screen .................................................. 36
Troubleshooting .............................................. 37
Precautions for Proper Use ............................. 39
Specifications .................................................. 43
Software License Agreement .......................... 45
Important Notice concerning the Software ....... 47
Content of this manual
Symbols used
Caution : Describes precautions concerning the
operation of this product.
Memo : Describes reference information, such as
functions and usage restrictions of this
product.
O
: Function that operates only when the handle
unit is attached.
F
: Function that operates only with a compatible
commercially available lens.
Verifying the Accessories
Verify that the following accessories are included
with the camera recorder before using.
Accessories
Warranty Card (U model only) 1
INSTRUCTIONS (BASIC) 1
Document Disc 1
AC Adapter 1
Power Cord (U model: 1, E model: 2)
Battery 1
Handle Unit 1
Microphone 1
* Eyepiece and body cap are attached to the
camera recorder.
Contents 9
Introduction

Names of Parts
.
D
A
B
C
E
G
H
F
I
A[ND FILTER] ND Filter Switch
BLens Release Button
CLens Mount
DBuilt-in Microphone
EHandle Unit
Memo :
0The handle unit is detached from the camera
recorder unit in the factory shipment.
For details on attaching the handle unit, please
refer to [Attaching the Handle Unit] .
F[MODE] Camera/Media Mode Selection Button
G[POWER ON/OFF] Lock Power ON/OFF Switch
Turns ON/OFF the power.
0Hold down the lock button (blue) in the center
to toggle ON/OFF.
0When the power is turning OFF, “P.OFF”
appears on the LCD monitor and viewfinder.
0Wait for 5 seconds or more to turn on the
power again.
H[POWER/CHARGE] Power/Charging Display
Lamp
I[AWB/9] Auto White Balance/User 9 Button
.
K
P
O
Q
L
M
N
R
oBottom
S
J
JVisibility Adjustment Lever
KBattery
LViewfinder
MEyepiece
NMicrophone
O[REC/7] Record Trigger/User 7 Button
PZoom Lever at the Grip
Q[EXPANDED FOCUS/8] Expanded Focus
Assist/User 8 Button
RTally Lamp
STripod Mounting Hole
10 Names of Parts
Introduction

Side Control Panel
.
B
F
G
D
C
MN J I HL K
E
A
A[LOCK/10] AE/FAW Lock/User 10 Button
B[AF/MF] Focus Selection Button
C[AUTO MODE FULL/PRESET/OFF] Auto Mode
Switch
For switching the Auto mode.
Memo :
0This camera recorder is set to Full Auto mode in
the factory default.
D[F.ASSIST/1] Focus Assist/User 1 Button
E[TC/2] Time Code/User 2 Button
FLCD monitor
GJ / K Volume Buttons/[+/-] Selection Buttons
H[SHUTTER] Shutter Speed Button
I[AE LEVEL] Automatic Brightness Adjustment
(AE) Level Setting Button
J[MARKER/6] Marker Display/User 6 Button
K[WHT BAL B/A/PRST] White Balance Switch
L[GAIN L/M/H] Gain Switch
M[IRIS A/M] Auto Iris/Manual Iris Button
NIris Dial
Side Terminal Section
.
A
D
C
B
A[HOST] USB Host Terminal
B[DEVICE] USB Mini Terminal
C[HDMI] HDMI Output Terminal
D[SDI OUT] SDI Output Terminal
Rear Terminal
.
C
B
D
A
GFEH
A[BATTERY] Terminal
B[BATT. RELEASE] Battery Lock Release Button
C[REC] Record Trigger Button
Memo :
0This button is interlocked with the [REC/HOLD]
record trigger button I on the the handle unit.
D[DC] DC Input Terminal
E[REMOTE] Remote Terminal
F[AUX] AUX Input Terminal (Φ3.5 mm)
G[x] Headphone Jack (Φ3.5 mm)
H[AV] AV Output Terminal
Names of Parts 11
Introduction

LCD Monitor
.
G
F
E
H
I
J
D
B
A
C
L KM
ALCD Monitor
B[CANCEL/STOP] Cancel/Stop Button
CLCD Cross-Shaped Button (JKHI)/Set Button
(R)
D[MENU/THUMB] Menu/Thumbnail Button
E[LOLUX/3] Low-light Shooting/User 3 Button
F[C.REVIEW/4] Clip Review/User 4 Button
G[ZEBRA/5] Zebra/User 5 Button
H[DISPLAY] Display Button
I[STATUS] Status Screen Display Button
JMonitor Speaker
KSD Card Slot
LCard Slot A/B Status Indicator
M[SLOT SEL] Card Slot Selection Button
Handle Unit Section
.
D
C
F
A
B
E
L
H
I
G
S
T
Q
R
J
OPNM
K
AMicrophone Holder
BMicrophone Holder Lock Knob
CHandle Tally Lamp
DAccessory Mounting Screw Hole
EShoe
FHandle Unit Fastening Screw
GZoom Lever on Handle
H[ZOOM L/M/H] Zoom Speed Switch
I[REC/HOLD] Record Trigger Button/Lock
Switch
Memo :
0This switch is interlocked with the [REC] button
C on the rear terminal.
0[REC] button C on the rear terminal is not
locked.
J[INPUT1/INPUT2] Audio Input Terminal 1, 2
(XLR 3-pin x 2)
KCable Clamp for Microphone
LHandle Terminal
M[CH-1] CH1 Audio Input Signal Selection Switch
N[CH-2] CH2 Audio Input Signal Selection Switch
O[AUDIO INPUT INPUT1] Audio Input Signal
Selection Switch
P[AUDIO INPUT INPUT2] Audio Input Signal
Selection Switch
Q[AUDIO SELECT CH-2 AUTO/MANU] CH2
Audio Recording Mode Switch
R[CH-2] CH2 Recording Level Adjustment Knob
S[CH-1] CH1 Recording Level Adjustment Knob
T[AUDIO SELECT CH-1 AUTO/MANU] CH1
Audio Recording Mode Switch
12 Names of Parts
Introduction

Attaching the Handle Unit
The handle unit is detached from the camera
recorder unit in the factory shipment.
To use the handle unit, attach it by following the
steps below.
* Attach or detach the handle unit when the power
is turned off.
.
1Fit the handle terminal at the bottom of the
handle unit to the handle unit mount at the
top of the camera recorder.
0Fit the handle unit carefully, paying attention
not to damage the terminals at the bottom of
the unit.
2Slide the handle unit in the direction
indicated by the arrow to attach it to the hot
shoe of the camera recorder.
3Press the screw on the handle unit and turn
it in the clockwise direction. Tighten it
securely to fasten the unit to the camera
recorder.
0The handle unit may be unsteady if the screw
is not securely fastened, and may fall off
during use.
Caution :
0Attach or detach the handle unit when the power
is turned off.
Doing so when the power is turned on can result
in malfunction.
Attaching the Lens
(Commercially Available)
You can attach the Micro Four Thirds Mount lens
on this camera recorder.
*After attaching the lens, perform the VSM
(Variable Scan Mapping) setting as needed.
For details, please refer to the
“INSTRUCTIONS” provided in the supplied
document disc (CD-ROM).
Caution :
0Check that the camera recorder is turned off
before attaching the lens. Attaching the lens with
the power turned on can result in accident and
malfunction.
0When detaching the lens, do not touch the
sensor or allow dust to adhere to the sensor.
.
1
2
3
1Detach the body cap.
0Do not lose the body cap, keep it properly.
2Attach the lens.
0Align the attachment mark on the lens with
the lens alignment mark (red dot) on the
camera recorder, and then insert the lens
onto the camera recorder.
0Turn the lens clockwise until a “click” sound
is heard.
Memo :
0To detach the lens, press the lens release button
and turn the lens counterclockwise.
0For details on the lens, please refer to the
“INSTRUCTIONS” of the lens used.
Attaching the Handle Unit 13
Preparations

Adjusting the Grip Belt
Open the pad and adjust the position of the grip belt
accordingly.
.
Caution :
0If the grip is loose, the camera recorder may fall
off resulting in injuries or malfunction.
Attaching the Supplied
Microphone O
You can attach the supplied microphone to the
microphone holder.
The supplied microphone uses a phantom power
supply.
.
4
5
1, 3
2
1Turn the knob on the microphone holder
counterclockwise to loosen and open the
microphone holder.
2Place the microphone in the microphone
holder.
3Turn the knob on the microphone holder
clockwise to secure the microphone.
4Connect the microphone cable to the
[INPUT1] or [INPUT2] terminal.
5Pin the microphone cable to the clamp.
6Perform the settings for the phantom mic
correctly.
Charging the Battery
Charging the Battery
Charge the battery immediately after purchase or
when the battery power is running low.
*The battery is not charged when purchased.
.
3
2
1
4
1
Hold down the lock button (blue) at the
center of the [POWER ON/OFF] switch to set
to “OFF”.
2Attach the supplied battery.
Slide it in until you hear a click.
3Connect the supplied AC adapter to the
[DC] terminal.
Open the cover of the [DC] terminal and connect
as shown in the diagram.
4Connect the AC adapter to a power outlet.
0The [POWER/CHARGE] lamp blinks during
charging and will go out after charging is
complete.
0Remove the AC adapter after charging is
complete.
14 Adjusting the Grip Belt
Preparations

Memo :
0Blinking of the [POWER/CHARGE] lamp during
charging indicates the charge level.
[POWER/CHARGE] Lamp Charge Level
Alternates between a blinking
orange light (4 times) and
light off (1 second)
Less than 25 %
Alternates between a blinking
orange light (3 times) and
light off (1 second)
Less than 50 %
Alternates between a blinking
orange light (2 times) and
light off (1 second)
Less than 75 %
Alternates between a blinking
orange light (blinks once) and
light off (1 second)
Less than 100 %
Light goes out Fully charged
0You can charge the battery even when operating
the camera recorder using the AC adapter.
Removing the Battery
.
1
2
1
Hold down the lock button (blue) at the
center of the [POWER ON/OFF] switch to set
to “OFF”.
2While pressing and holding the [BATT.
RELEASE] button, push up and remove the
battery in the direction of the arrow.
Caution :
0Do not remove the battery when the [POWER
ON/OFF] switch is “ON”.
0Do not insert or remove the DC cable when the
battery is in use.
0Leaving the camera recorder unused with the
battery inside will deplete the battery power
even if you set the [POWER ON/OFF] switch to
“OFF”. Remove the battery if you are not using
the camera recorder.
Estimated Charging and Continuous
Operating Times
oCharging time
SSL-JVC50 (accessory) : Approx. 4 hrs
*
When the [POWER ON/OFF] switch is set to “OFF”
Memo :
0If you charge the battery immediately after using
while the battery is still warm, it may not be fully
charged.
0For details, refer to the “INSTRUCTIONS” of the
battery.
oContinuous operating time
SSL-JVC50 (accessory) : Approx. 3 hrs 45 mins
(*1)
Approx. 4 hrs (*2)
*1 When [System] is set to “4K” and all other
settings are in factory default (excluding the
lens)
*2 When [System] is set to “HD” and all other
settings are in factory default (excluding the
lens)
Memo :
0Actual operating times may differ depending on
the age of the battery, charging condition, and
operating environment.
0Operating time is shortened in cold
environment.
0The operating time may shorten when power
zoom is used, accessories are connected, or
when the LCD monitor is frequently used.
0For purchase of spare batteries and battery
charger, please contact the local dealers in your
area.
Charging the Battery 15
Preparations

Configuring the Initial
Settings
When the power is first turned on, the Initial Setting
screen for performing the initial settings in the
camera recorder appears.
Set the date/time of the built-in clock in the [Initial
Setting] screen.
All operations are disabled until initial settings are
complete.
.
Memo :
0It is recommended to use the AC adapter as the
power supply.
0Attach the lens cap.
1
Hold down the lock button (blue) at the
center of the [POWER ON/OFF] switch to set
to “ON”.
A language selection screen appears.
0For U models
.
Español
Français
English
Language
0For E models
.
Pусский
Español
Italiano
Deutsch
Français
English
Language
Memo :
0The menus and messages on the screen of the
LCD monitor or viewfinder are displayed in the
selected language.
2Select a language using the cross-shaped
button (JK), and press the Set button (R).
The Initial Setting screen appears.
.
Diagnose
The Time is about 6 minutes.
with lens cap.
try self diagnosis attaching
Prior to the first operation,
3Ensure the lens cap is attached, and press
the Set button (R).
0Self-diagnosis starts.
0A progress bar appears, and “Complete
Diagnosis” appears when the diagnosis is
complete.
.
Close
Complete Diagnosis
Don't Remove Lens Cap.
Diagnosing...
Memo :
0It takes about 6 minutes to complete the
diagnosis. During the diagnosis, do not operate
or turn off the camera recorder.
16 Configuring the Initial Settings
Preparations

4Press the Set button (R) after confirming
the exit screen.
The [Initial Setting] screen appears.
0For U models
.
Set
UTC-05:00
Initial Setting
0For E models
.
Set
UTC
Initial Setting
Memo :
0The [Initial Setting] screen appears when the
power is turned on for the first time and when the
power is turned on after the built-in battery is fully
discharged.
0The configured date/time data is saved in the
built-in rechargeable battery even if the power is
turned off.
5Set the time zone and date/time.
AMove the cursor with the cross-shaped button
(HI) and select the setting item.
BChange the values with the cross-shaped
button (JK).
6Press the Set button (R) after setting is
complete.
The clock is set to 0 seconds of the input date/
time.
Memo :
0The configured date/time data can be displayed
on the LCD monitor and viewfinder and be
recorded to the SD card.
0The value of the year can be set in the range of
“2000” to “2099”.
Usable Cards
Format Setting and Usable SD Card
Combinations
System Format Bit Rate Usable SD
Card
4K - - UHS-I U3 or
higher
HD QuickTime
50M (YUV422),
50M (XHQ)
Class 10 or
higher
35M (UHQ) Class 6 or
higher
AVCHD - Class 4 or
higher
SD - -
Web - -
Caution :
0Using cards other than those from Panasonic,
TOSHIBA or SanDisk may result in recording
failure or data loss.
0If an UHS-I card with no classification indication
is used, it may not be possible to perform HD
recording.
Configuring the Initial Settings 17
Preparations

Estimated Recordable
Time of SD Cards
The estimated recordable time is only a guide.
Differences may occur depending on the SD card
in use and the battery condition.
oWhen [Main Menu] B [System] B [Record Set]
B [Record Format] B [Format] is set to
“AVCHD”
Resolution
1080p
1080i 480i/
576i
Bit Rate HQ HQ SP LP EP -
4GB 16 19 25 46 82 50
8GB 33 39 50 95 168 103
16GB 67 78 100 190 336 209
32GB 135 156 200 380 672 420
64GB
(SDXC)
270 312 400 760 1344 842
128GB
(SDXC)
540 624 800 1520 2688 1687
(Unit: minute)
oWhen [Main Menu] B [System] B [Record Set]
B [Record Format] B [Format] is set to
“QuickTime”
System 4K HD SD Web
Resolution 2160p 1080i/1080p 480i/
576i
960p 480p
Bit Rate - XHQ UHQ - HQ LP
4GB 3 9 12 47 130 285
8GB 6 18 25 95 270 580
16GB 12 36 50 190 540 1160
32GB 25 72 100 380 1080 2320
64GB
(SDXC)
50 145 200 760 2160 4720
128GB
(SDXC)
100 290 400 1520 4320 9440
(Unit: minute)
Memo :
0If the SD card contains files recorded by devices
other than this camera recorder or files that are
saved from a PC, the recordable time may be
shorter or data may not be properly recorded.
0For each file format, up to 600 clips can be
recorded to one SD card on this camera
recorder. When 600 clips are recorded to one
card, the remaining space is displayed as 0 min
regardless of the estimated recordable time,
and no further recording can be performed.
0When the file format is set to “AVCHD”, up to
4000 clips can be recorded to one SD card.
Inserting an SD Card
This camera recorder comes with two card slots
(Slot A and B) for video/audio recording and
playback.
.
1
3
SD Card Cover
2
SD Card
1Open the SD card cover by sliding the cover
in the direction indicated by the arrow.
2Insert an SD card with the notched corner
pointing up.
The status indicator of the card slot to which the
card was inserted lights up in red.
3Close the SD card cover in the direction
indicated by the arrow.
18 Estimated Recordable Time of SD Cards
Preparations

Formatting (Initializing) SD Cards
When the following cards are inserted, [!FORMAT]
appears at the remaining media display area.
Format the card using the camera recorder menu.
0Unformatted SD cards
0SD cards formatted under different
specifications
Caution :
0Be sure to format the SD card on this camera
recorder. SD cards formatted on a PC and other
peripheral equipment cannot be used on this
camera recorder.
0[!RESTORE] appears at the remaining media
display area when an SD card that requires
restoring is inserted.
1Select [System] B [Media] B [Format
Media].
2Select the slot of the SD card to be
formatted and press the Set button (R).
.
2
Set
Format Media
Format Slot A
Format Slot B
3The status of the selected SD card appears.
4Select [Format] and press the Set button
(R).
.
4
Set
Cancel
Format
Format Media
5Formatting starts.
.
Formatting...
6Formatting is complete.
When formatting is complete, “Complete” appears
and the camera recorder returns to the [Format
Media] screen.
Memo :
0During formatting, menu operation is
unavailable but you can start recording.
However, this is only available when a
recordable SD card is inserted in the other slot.
0Formatting cannot be performed in the following
cases.
0Recording is in progress on the SD card to be
formatted.
0SD card is not inserted.
0Write-protect switch of the SD card is set (z
is displayed).
Caution :
0If you format the SD card, all data recorded on
the card, including video data and setup files,
will be deleted.
Inserting an SD Card 19
Preparations

Clips Recorded to SD Cards
Folders in the SD Card
The captured image is recorded into different
folders according to the [System] and [WFormat]/
[YFormat] settings.
System WFormat/
YFormat Record Folder
4K/HD/SD/
Web
QuickTime DCIM
HD/SD/
Web
AVCHD PRIVATE/AVCHD
Memo :
0By formatting (initializing) the SD card from the
[Format Media] menu on the camera recorder,
folders required for recording in the current
[System] settings will be generated.
0When the [System] settings and [QuickTime]
settings are changed, folders required for
recording in those settings will be automatically
generated.
Caution :
0When a clip inside the folder is moved or deleted
using the Explorer (Windows) or Finder (Mac),
recording to the SD card may fail if formatting
(initializing) of the card is not performed.
Clip (Recorded Data) and Clip Name
0When recording is stopped, the images, audio
and accompanying data which are recorded
from start to stop are recorded as one “clip” on
the SD card.
0An 8-character clip name is automatically
generated for the recorded clip.
(“Clip Name Prefix” + “Clip Number”)
0When [Main Menu] B [System] B [Record Set]
B [Record Format] B [WFormat] is set to
“AVCHD”, the clip name generated consists of
only the Clip Number (5-digit number).
Example: QuickTime
.
ABCG0001
This is set to “xxxG” (“xxx” denotes the last 3
digits of the serial number) by default.
Clip Name Prefix (any four alphanumeric characters)
The Clip Number can be reset in
the menu.*
A number in automatic
ascending order is assigned in
the recording order.
Clip Number
* [Clip Set] B [Reset Clip Number]
Memo :
0Before recording starts, you can set any
characters for the clip name prefix by using
[Main Menu] B [System] B [Record Set] B [Clip
Set] B [Clip Name Prefix].
0Changes cannot be made after recording.
Recorded Clips
0The recorded materials may be split into several
files but they can be played back continuously
on the camera recorder.
0Clips may be recorded across the two SD cards
in card slots A and B depending on the recording
time of the clip.
Caution :
0A clip recorded across several cards cannot be
played back continuously. Continuous playback
is only possible when the recording is made on
one card.
20 Inserting an SD Card
Preparations