JVC TK-AM200U - Active Movement Color Dome... User manual

3
TK-AM200 INSTRUCTIONS
For Customer Use:
Enter below the Serial No. which is
located on the body. Retain this
information for future reference.
Model No. TK-AM200
Serial No.
This instruction book is made from
100% recycled paper.
ACTIVE MOVEMENTVIDEO CAMERA
SC96866-001

2
IMPORTANT SAFEGUARDS
1. Read all of these instructions.
2. Save these instructions for later use.
3. All warnings on the product and in the operating instructions should be adhered to.
4. Unplug this appliance system from the wall outlet before cleaning.Do not use liquid clean-
ers or aerosol cleaners.Use a damp cloth for cleaning.
5. Do not use attachments not recommended by the appliance manufacturer as they may
cause hazards.
6. Do not use this appliance near water - for example, near a bathtub, washbowl, kitchen
sink, or laundry tub, in a wet basement, or near a swimming pool, etc.
7. Do not place this appliance on an unstable cart, stand, or table.The
appliance may fall, causing serious injury to a child or adult, and
serious damage to the appliance.
Use only with a cart or stand recommended by the manufacturer, or
sold with the appliance.Wall or shelf mounting should follow the
manufacturer’s instructions, and should use a mounting kit approved
by the manufacturer.An appliance and cart combination should be
moved with care.
Quick stops, excessive force, and uneven surfaces may cause the
appliance and cart combination to overturn.
8. Slots and openings in the cabinet and the back or bottom are provided for ventilation, and
to insure reliable operation of the appliance and to protect it from overheating, these
openings must not be blocked or covered. The openings should never be blocked by
placing the appliance on a bed, sofa, rug, or other similar surface.
This appliance should never be placed near or over a radiator or heat register.This appli-
ance should not be placed in a built-in installation such as a bookcase unless proper
ventilation is provided.
9. This appliance should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supplied to your home, consult your
dealer or local power company. For appliance designed to operate from battery power,
refer to the operating instructions.
10.This appliance system is equipped with a 3-wire grounding type plug (a plug having a
third (grounding) pin).This plug will only fit into a grounding-type power outlet.This is a
safety feature.If you are unable to insert the plug into the outlet, contact your electrician to
replace your obsolete outlet.Do not defeat the safety purpose of the grounding plug.
11.For added protection for this product during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall outlet and disconnect the
antenna or cable system.This will prevent damage to the product due to lightning and
power-line surges.
12.Do not allow anything to rest on the power cord. Do not locate this appliance where the
cord will be abused by persons walking on it.
PORTABLE CART WARNING
(symbol provided by RETAC)
S3126A

3
13.Follow all warnings and instructions marked on the appliance.
14.Do not overload wall outlets and extension cords as this can result in fire or electric shock.
15.Never push objects of any kind into this appliance through cabinet slots as they may touch
dangerous voltage points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the appliance.
16.Do not attempt to service this appliance yourself as opening or removing covers may
expose you to dangerous voltage or other hazards.Refer all servicing to qualified service
personnel.
17.Unplug this appliance from the wall outlet and refer servicing to qualified service person-
nel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the appliance.
c. If the appliance has been exposed to rain or water.
d. If the appliance does not operate normally by following the operating instructions.Ad-
just only those controls that are covered by the operating instructions as improper
adjustment of other controls may result in damage and will often require extensive
work by a qualified technician to restore the appliance to normal operation.
e. If the appliance has been dropped or the cabinet has been damaged.
f. When the appliance exhibits a distinct change in performance - this indicates a need
for service.
18.When replacement parts are required, be sure the service technician has used replace-
ment parts specified by the manufacturer that have the same characteristics as the origi-
nal part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
19.Upon completion of any service or repairs to this appliance, ask the service technician to
perform routine safety checks to determine that the appliance is in safe operating
condition.

4
CAUTION:TO REDUCE THE RISK OF ELECTRIC
SHOCK. DO NOT REMOVE COVER (OR
BACK).NO USER-SERVICEABLE PARTS
INSIDE.REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle is
intended to alert the user to the pres-
ence of uninsulated "dangerous volt-
age" within the product's enclosure that
may be of sufficient magnitude to con-
stitute a risk of electric shock to per-
sons.
The exclamation point within an equi-
lateral triangle is intended to alert the
user to the presence of important op-
erating and maintenance (servicing)
instructions in the literature accompa-
nying the appliance.
WARNING:
TO REDUCETHE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT
EXPOSETHIS APPLIANCETO RAIN
OR MOISTURE.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
This device complies with part 15 of the FCC Rules.
Changes or modifications not approved by JVC could
void the user’s authority to operate the equipment.
Due to design modifications, data given in this
instruction book are subject to possible change
without prior notice.
AVERTISSEMENT:
POUR EVITER LES RISQUES
D’INCENDIE OU D’ELECTRO-
CUTION, NE PAS EXPOSER
L’APPAREIL A L’HUMIDITE OU A LA
PLUIE.
Safety Precautions
INFORMATION (FOR CANADA)
RENSEIGNEMENT (POUR CANADA)
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la Class B est
conforme á la norme NMB-003 du Canada.

5
Thank you for purchasing this product.
(These instructions are forTK-AM200U.)
CONTENTS
INTRODUCTION
Features.............................................................................................................................. 6
Safety Precautions.............................................................................................................. 6
Operating Precautions........................................................................................................ 7
Controls, Connectors and Indicators...................................................................................8
Camera Body ................................................................................................................. 8
Ceiling Mount ................................................................................................................. 9
SYSTEM
RM-P2580 System............................................................................................................ 10
INSTALLATION
Connections to Terminal Board ........................................................................................ 12
Camera Settings ............................................................................................................... 14
Ceiling Installation ............................................................................................................ 16
Changing Camera Settings Using the RM-P2580
Menu Operations .............................................................................................................. 18
Menu Screen Flow............................................................................................................ 19
CAMERA MODE SELECT Screen................................................................................... 20
CAMERA VIDEO ADJUST Screen................................................................................... 21
AWC ADJUST Screen ...................................................................................................... 22
VIDEO ADJUST FOR POSI Screen................................................................................. 23
PANIC ALARM SET Screen ............................................................................................. 24
FACTORY SETTINGS Screen.......................................................................................... 24
BLC EDIT Screen ............................................................................................................. 25
CAMERA TEXT Setting .................................................................................................... 26
POSITION TEXT Setting .................................................................................................. 27
AUTO PAN Setting ............................................................................................................ 28
AUTO PATROL Setting ..................................................................................................... 30
OTHERS
PANIC ALARM.................................................................................................................. 32
Specifications.................................................................................................................... 34

6
INTRODUCTION
nActive movement camera with integrated
moving mechanism and camera.
nBacklight compensation function
provided.Enables improvement of video
image shot under backlit conditions.
nElectronic shutter with a selectable
shutter speed of 1/100 sec reduces
flickering caused by fluorescent lighting
in areas where the commercial power
supply frequency is 50 Hz.
nEmployment of TTL automatic tracking
white balance allows use under various
light source conditions.
nPanic alarm input terminal provided.
nElectronic zoom function.
nControl possible via external control
signal conforming to the EIA/TIA RS-
422A or RS-485 standard.The unit can
be controlled using the optional JVC
Remote Control Unit RM-P2580.
nThe following functions are available
when used in combination with the JVC
Remote Control Unit RM-P2580.
• Many kinds of function can be set using
menus.
• Camera text, position text setting.
• Auto panning function
• Auto patrol function
This function outputs the video image
at specified pre-set positions in the set
order.
Features Safety Precautions
Installation of this unit requires expertise.
Please contact your JVC dealer for details.
Be sure to tighten the screws and nuts used
for installation securely.Insufficient tightening
could cause the unit to fall from its mount.

7
Operating Precautions
●To save energy, be sure to turn off the
system when not in use.
●This camera has been designed for indoor
use.It cannot be used outdoors.
●This camera has been designed
exclusively to be hung from the ceiling. It
may malfunction if it is placed standing
on a surface or if it is installed in a tilted
position.
●Do not install or use the camera in the
following places.
• In a place exposed to rain or water.
• In a place with vapor or oil soot, for
example in a kitchen.
• Where the temperature is outside the
allowed operating temperature range
(−10°C to 50°C).
• Near a source of radiation, X-rays,
strong radio waves or magnetism.
• In a place subjected to vibrations.
• In a place with excessive dirt.
●The camera incorporates an AGC circuit.
When it is used under low light conditions,
the camera sensitivity is automatically
boosted and the picture may look grainy.
This is not a malfunction.
●Use the ATW (auto-tracking white
balance) mode when the camera is used
under fluorescent lighting. If set to
MANUAL, the correct white balance may
not be accomplished.
●When this camera is used in the ATW
(auto-tracking white balance) mode, the
recorded colors may be slightly different
from the actual colors due to the
operational principles of the auto-tracking
white balance circuit. This is not a
malfunction.
●If a high-intensity object (such as a lamp)
is shot, the image on the screen may have
vertical lines (smear) or blur (blooming)
at its periphery.This is a characteristic of
the CCD; and it is not a defect.
●The camera’s electronic shutter is set to
1/60 s when shipped from the factory.
When the camera is used under
fluorescent lighting in an area with a local
power frequency of 50 Hz, please set the
shutter to 1/100 s on remote control unit.
(Sensitivity will decrease slightly at the 1/
100 s setting.)
●When dirt adheres to the dome cover, the
image will be difficult to see. Be sure to
clean the lens and the dome cover
periodically.Use a soft cloth for cleaning.
Do not use thinner, benzene, etc. If very
soiled, soak the cloth in a neutral
detergent diluted with water and wipe
clean.Then wipe with a dry cloth.
Precautions for use with the RM-P2580
●Focus (including AF) cannot be used.
●Do not select more than maximum 16
preset positions.
●ALARM TEXT EDIT 1 to EDIT 10
cannot be used.

8
1Terminal board
To connect the coaxial cable used as the
video signal cable, the power cable, the
control signal cable, and the alarm input
signal cable. (ZSee page 12.)
2Video output terminal
Outputs composite video signals
(1V(p-p), output impedance 75 Ω).
3
Control signal connection terminals
Terminals for inputting signals with elec-
trical characteristics conforming to the
EIA/TIA RS-422A or RS-485 standard.
4AC 24V input terminal
To input AC 24 V power.
5Panic alarm signal input terminal
Terminal for inputting the panic alarm sig-
nal.Settings concerning the panic alarm
signal should be made using the PANIC
ALARM SET screen. (ZSee pages 24
and 32.)
6
Terminal board cover
Protects the cable connection terminals
from dirt, etc.
7
Camera body mounting guides (×3)
To be inserted into the guide holes
16
of
the ceiling mount.
8
Camera body clamp
Fix the camera body to the ceiling mount
by fastening the ceiling mount’s camera
clamping screw
18
to this clamp.
9
Drop prevention wire hook
Attach the drop prevention wire
20
from
the ceiling mount to this hook.
10
Switch cover
Open this cover to use the setting
switches.The cover can be opened by
pushing the cover edge in the direction
of the arrow.
11
Control signal selector switch
(RS-422A/RS-485, RS-232C)
Switches the communication mode of the
control signal terminal 3.
• When connected to the RM-P2580, set
to the RS-422A/RS-485 side.
• When connected to a personal com-
puter, etc. set to the RS-232C side.
Controls, Connectors and Indicators
nCamera Body (With terminal board in attached condition)
INTRODUCTION
(Side view)
7
6
9
2
7
7
3
5
4
1
8
0
$
#@!

9
12
System setting switches
Set switches in accordance with the sys-
tem to be connected to.
The settings comprise setting the form
of the control signal cable connection,
communication protocol, control signal
termination ON/OFF, and image synchro-
nization method.
(ZSee “Camera Settings” on page 14.)
13
Camera ID setting switches
Use to set the camera ID.
Be sure to set the camera ID when switch
1 of the system setting switches
12
is
set to ON (MULTIDROP).
(ZSee “Camera Settings” on page 14.)
14
FOR SERVICE connector
Exclusively for service purposes.
Ceiling Mount
15
Mounting holes ( × 4)
Use these holes to attach the ceiling
mount to the ceiling.
16
Guide holes for mounting camera ( × 3)
Guide holes for mounting the camera
body.The camera body mounting guides
7
are inserted into these holes.
17
Camera direction alignment mark
When mounting the ceiling mount to the
ceiling, align this mark with the center of
the direction in which you want the cam-
era to face.
18
Camera clamping screw
To hold the camera body in place, be sure
to use this screw to clamp the camera
clamp 8.
19
Positioning alignment protrusion
When attaching the camera body, align
the camera clamp
8
on the camera
body with this protrusion.
20
Drop prevention wire hook
Attach this wire to the drop prevention
wire hook 9on the camera body.
21
Safety wire attachment hole
To prevent the camera from accidentally
dropping down, fasten a wire from the
ceiling to this hole using an M3 screw.
(ZSee “Ceiling Installation” step
2. on
page 16.)
nCeiling Mount
21
%
%
*
^)
&
^
%
^
%
(

10
SYSTEM
RM-P2580 System
nSystem with up to 8 cameras
(Sixteen position settings available for each camera.)
• Confirm switch settings on the screen as follows.
qConfirm that the image from the camera to be
checked is displayed on the monitor.
wTurn OFF and then ON the AC 24 V power to the
camera to be checked.
eThe camera begins the initial operation and
characters similar to those shown in the illustration
on the right appear on the monitor screen.
rConfirm that “DUPLEX”and “ID- ”are displayed
and that the ID number is the correct number (the
number should be the same as the number of the
VIDEO INPUT terminal to which the camera is
connected on the rear panel of the RM-P2580).
tIf wrong, set the camera ID again.
MONITOR screen
(example showing camera ID as “05”)
“DUPLEX” should
be displayed. The number shown in
the □□ part of ID-□□
should be correct.
REC
PLAY
FFREW
REVERSE PAUSE/
STILL
REC
CHECK
STOP/EJECT
COUNT/
CLOCK
TIME
MODE TIMER REC AL/PL RESET
MENU
VIDEOCASSETTE RECORDER
SHIFT/TRACKING
SET/V.LOCK
RESET
/CANCEL
OPERATE
SR-L910
OPE.LOCK
1
TO CAMERATO CAMERA DATA I / ODATA I / O
RXRX+ { RX
-
| TX+ { TX
-
| COMCOM 1 2 3 4 5 6 7 8 COMCOM 9/1 10/2 11/3 12/4 13/5 14/6 15/7 16/8 COMCOM COMCOM COMCOM
CAMERACAMERA
SW
UNIT
ALARM AUTO
431 2 875 6
2 3 4 5 6 7 8
1
MONITOR
OUTPUT MONITOR
SERIAL-2SERIAL-1
VIDEO INPUT
VIDEO OUTPUT
OUTPUT
2
1
ON
2 3 4 5 6 7 8
POWER
OFF
ON
AC INPUT
‘
IN TIALI
PROT OOLDUPLEXID-05C
Camera
TK-AM200
Camera
TK-AM200
Camera
TK-AM200
Camera 1
Camera 2
Camera 8
Camera ID: 01
Termination: OFF
Camera ID: 02
Termination: OFF
Camera ID: 08
Termination: ON
Control signal cable
Video signal cable
Power cable
Remote Control Unit
RM-P2580
Time lapse VCR MONITOR
MONITOR
AC24V
AC24V
AC24V
CAM SW
OUT
VIDEO IN
COM
CAMERA
SW
TO
CAMERA
MONITOR
OUTPUT 2
MONITOR
OUTPUT 1
Memo:
• When operating a system using the RM-P2580, several cameras (up to 8) can be connected and
used on one control signal cable.Consequently, an incorrect switch setting on just a single camera
will cause the entire system to work incorrectly.

11
nConnections
nSettings
When connecting
●Turn OFF the power supply to all equipment to be used before making connections.
●Carefully read the Instruction Manual for each piece of equipment to be used before
making connections.
●For the appropriate connection cables and the length of these, carefully read“Connections
to Camera Terminal Board” on page 12.
●The control signal cable cannot be used for loop connection.
Lug plates AC 24 V power cable
To AC 24V power
supply
To RM-P2580
To VIDEO INPUT
terminal on
RM-P2580
Connecting the control signal cable
(
Use a twisted-pair cable for connection. ZSee page 13. )
Camera 2
terminal board Connect:
Camera TX+ to RM-P2580 RX+
Camera TX– to RM-P2580 RX–
Camera RX+ to RM-P2580 TX+
Camera RX– to RM-P2580 TX–
The ABCDmarks indicated
on both the camera terminals
and the RM-P2580 terminals
facilitate correct connections.
Connect the terminals with
identical marks.
CTX+
DTX–
ARX+
BRX–
TX+A
TX–B
RX+C
RX–D
TX+A
TX–B
RX+C
RX–D
TX+A
TX–B
RX+C
RX–D
RM-P2580
Camera 1
terminal board
Camera 3
terminal board
Control
signal cable
Video signal cable
(coaxial cable)
Terminal board
RX+ C
RX– D
A TX+
B TX–
1234
ON 0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
Camera ID setting switches
Set to match the RM-P2580 VIDEO
INPUT terminal number for each
camera.
Switch 3: Set this to ON (signal termination ON) only
on the camera placed at the end of the
control signal cable.
Set to OFF on all other cameras.
Switch 2: Set to OFF (DUPLEX) side.
Switch 1: Set to ON (MULTIDROP) side.
Control signal selector switch:
Set to the RS-422A/RS-485 side.
(Example: Camera 1
ID “×10” position 0,
ID “×1” position 1)
Switch 4: Select the synchronization method of the
camera image.
Set the switch on all cameras to ON (Line
Lock) and match with theV. PHASE.
(Only possible in 60 Hz regions.)
(ZSee page 20.)

12
50 100 170 180 300 320 500
0.65 0.9 1.2 1.6 2.0
1.25 2.0
Connections toTerminal Board
Turn OFF the power supply to all equipment
to be used before making connections.
Connections toTerminal Board
Remove the terminal board cover and
connect the video signal cable (coaxial
cable) (
× 1). Connect the AC 24V power
cables (
× 2) and the control signal cables ( × 4).
When alarm input via the camera is used,
connect the alarm input cables ( × 2) to the
panic alarm signal input terminals.
mAC 24V power supply cable
Connect the AC 24V power supply to the
AC 24V terminals on the terminal board.
To prevent connection errors or a cable
disconnection, we recommend the use of
lug plates for the connections.
The following table shows the connection
distances.
Maximum extension (m)
CPEV, VVF, etc.
conductor diameter (mm)
CCV, etc. conductor
cross section (mm2)
INSTALLATION
Lug plates AC 24V power cable
To AC 24V power supply
RM-P2580
Video signal
cable (coaxial
cable)
Remove the terminal board cover
by flipping it up while pushing its
top to the left.
Control signal cable
or place the power supply near to the
camera. If voltage drop occurs during
operation, the performance will be
unstable.
• Be sure not to inadvertently connect the
AC 24V cable to an AC 120V power
supply.This could destroy the unit.
To switcher,
monitor, Remote
Control Unit RM-
P2580
Terminal board
CAUTION:
• If thin cables are used (i.e. with a high
resistance), a significant voltage drop
will occur when the unit is at its
maximum power consumption (pan, tilt,
zoom operated simultaneously). Either
use a thick cable to restrict the voltage
drop at the camera side to below 10%,

14
Camera Settings
1. Open the switch cover on the side.
To open the cover, pull outward while
pressing at the edge in the direction of
the arrow.
(Be sure not to press with excessive
force as this could deform or destroy the
cover.)
2. Set the control signal selector switch.
This switch is used to switch the input
and output signal to and from the con-
trol signal connection terminals.
When shipped from the factory, the
switch is set to “422A/485”. Normally,
there should be no need to change this
setting.When it becomes necessary to
change the setting, use a fine screw-
driver or other difficult to break or bend
object to change the setting.
INSTALLATION
Set the switches on the side of the camera in accordance with the system or equipment to
be connected to.
Always turn OFF the power before setting the switches.
Switch cover
Press.
Camera ID
setting switch
System setting
switches
Control signal
selector switch
Settings for use
with RS-422A/485
Settings for use
with RS-232C
RXD (signal input) GND (signal GND) TXD(signal output)
Control signal
connection
terminals
RX– (– signal input)
RX+ (+ signal input)
TX– (– signal output)
TX+ (+ signal output)
232C 422A
485
(Initial setting:
422A/485)
●422A: Use this setting when the
485 camera is connected to the op-
tional Remote Control Unit RM-
P2580.
Input and output of signals with
electrical characteristics con-
forming to the EIA/TIA RS-422A
or RS-485 standard takes
place.
●232C: Input and output of signals with
electrical characteristics con-
forming to the EIA/TIA RS-
232C standard takes place.
(When connecting to a personal
computer, etc.)
Memo:
The control signal selector switch setting
position and the signals input and output to and
from the control signal connection terminals are
as shown in the illustration on the left.
Improper setting could result in incorrect
operation or damage.
Empty

15
Double
figures Single
figures
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
"1""0"
●Switch 4: Synchronization signal
selector switch
Switches the synchronization method
of the camera image.
OFF: Internal synchronization (INT)
ON:
The camera’s vertical synchroniza-
tion is matched with the frequency
of the AC 24V line power supply.
When switching between mul-
tiple cameras using a switcher,
selecting this mode and adjust-
ing the vertical phase can re-
duce the monitor sync distur-
bances occurring when the
camera image is switched.(This
cannot be used in regions where
the power frequency is 50 Hz.)
●Switches 5, 6, 7, 8
These switches are not used.
(Set them to OFF.)
4. Camera ID setting switches
Camera ID setting is only performed
when the system connection selector
switches (Switch 1 and 2) are set to“RM-
P2580”.
The camera ID number is a number to
identify each of the cameras connect to
the RM-P2580.The camera ID number
should be the same as the number of
the RM-P2580 VIDEO INPUT terminal
to which the camera is connected.
Example:
The camera connected to VIDEO
INPUT 1 is set
to “01” as shown
on the right.
Memo:
If the camera ID numbers of cameras connect
to the RM-P2580 are duplicated, the system
will not work correctly.
5. When setting of the switches is com-
pleted, close the cover over the setting
switches again.
Memo:
Switch 1 and 2 are used to specify the
form of the control signal cable connection
between the remote control unit and the
camera and the communication protocol.
Switch 1 (Initial setting: OFF)
OFF: POINT TO POINT
ON: MULTIDROP
Switch 2: (Initial setting: OFF)
OFF: DUPLEX
(two-way data transmission)
ON: SIMPLEX
(one-way data transmission)
●Switch 3: Termination ON/OFF
switch
This is a termination ON/OFF switch
between the “RX+” and “RX–” control
signal connection terminals.
ON: The “RX+” to “RX–” route is ter-
minated by a 110Ωresistor.
OFF: The RX+ to RX– route is not
terminated.
(Initial setting: OFF)
In a system using the Remote Control Unit
RM-P2580, set this to “ON” only on the
cameraplaced at the end of the control sig-
nal cable.Set to OFF on all other cameras.
3. Set system setting switches.
Set the system connection selector
switches (Switch 1, 2) in accordance
with the equipment that the camera
body is to be connected to.
Connecting
equipment Switch 1 Switch 2
RM-P2580 ON OFF
●Switch 1, 2: System connection
selector switch
12345678
1
ON
1
OFF
Switches
ON
Switch numbers

16
Camera
direc-
tion
mark
3 mm
or
less.
Ceiling Installation
INSTALLATION
75 mm
1.
Drop prevention
wire
Hook
4.
Guide
Tab
Connector
cable
Tab
Guide
3.
Connector
on terminal
board
3. -1)
3. -1)
3. -2)
2.
White wire
To ceiling slab
or channel
M3 screw
Wire
Safety wire
attachment
hole
Memo:
Bundling the drop prevention wire together with the
cables connected to the terminal board using vinyl
tape will help prevent the cables from being
pinched.
CAUTION
Be sure to attach the drop prevention wire. If
not attached, the camera body could drop
down.
1. Make a hole (75 mm diameter) in the ceil-
ing for passing the connection cables.
2. Attach the provided ceiling mount to the
ceiling.
●Attach the ceiling mount so that the cam-
era direction mark is aligned with the direc-
tion in which you want the camera to face.
Coincide the center of the mount with the
hole (75 mm diameter) for passing the
cables through the ceiling.Attach the ceil-
ing mount to the ceiling using 4 screws.
●Use M4 screws or bolts for attaching the
ceiling mount.
●If wood screws are used, use screws with
a diameter of 4.1 mm.
●The screw head height should be no more
than 3 mm.
CAUTION:
To prevent the ceiling mount and
camera from dropping down, it is
recommended to connect the ceiling
mount to a ceiling slab or channel with
a wire.Fasten the wire to the safety wire
attachment hole using an M3 screw as
shown in the illustration.
3. Pass the wired terminal board through the
hole in the ceiling mount and attach it to the
camera body.
1) Slide the tab on the terminal board into
the guide on the camera.When the ter-
minal board is moved in the direction of
the arrow, it is secured to the camera.
2) Connect the connector cable from the
camera body to the connector on the ter-
minal board.
4. Attach the drop prevention wire.
As shown in the illustration, pull the drop
prevention wire out from the ceiling mount
and attach it to the drop prevention wire
hook on the underside of the camera body.

17
Positioning
alignment
protrusion
A
Camera
clamp
B
Camera clamping screw
Camera
clamp
Camera
clamping
screw
Ceiling mount
Camera
body
Camera clamping screw
(Slightly loosen)
(Tighten.)
5. 5.
Mount the camera body.
1) Ensure that the camera clamping screw
on the ceiling mount is loosened.
2) Align the ceiling mount’s positioning
alignment protrusion (Ain the illustra-
tion on the left) with the camera clamp
(Bin the illustration on the left) position
on the camera body and press the cam-
era body straight against the mount.
CAUTION:
Exercise caution so as not to pinch the
drop prevention wire and the connected
cables.
3) Rotate the camera body clockwise as far
as it will go.
At this point, check that the camera body
clamp is located on the camera clamp-
ing screw on the ceiling mount.
4) Tighten the camera clamping screw.
n Changing the position of the mounted
camera body
1) Slightly loosen the camera clamping
screw. By turning the camera body
counterclockwise, the position of the
mounted camera body can be
changed within a range of approxi-
mately 40 degrees (approximately 20
degrees to the left and right).
Memo:
Loosening the camera clamping screw too
much will cause the camera body to come
off the ceiling mount.
2) After the position for the camera body
is decided, tighten the camera clamp-
ing screw.
CAUTION
Be sure to tighten the camera clamping
screw fully. Otherwise the camera body
may vibrate or drop from the ceiling.
n
To dismount the camera from the ceiling,
perform steps 3. to 5. in reverse order.

18
Menu Operations
When the RM-P2580 is used as the remote control unit, the camera’s built-in menus can be
called up and set from the remote control unit.This function is explained on this page.
(For details, refer to the Instruction Manual for the remote control unit.)
Changing Camera Settings Using the RM-P2580
1. Set the power switch on the rear panel of
the remote control unit to ON.
2. When the MENU button is pressed for about
3 seconds, the LED lights up and the re-
mote control’s SETUP screen will be out-
put from the MONITOR OUTPUT-1 connec-
tor.
3. Use the PAN/TILT control lever to move the
cursor (>) and align it the CAMERA item.
●The cursor will move up when the lever is
pressed up (¶).
●The cursor will move down when the le-
ver is pressed down (Ä).
4. Press the SET button to display the SETUP
screen of the camera.
Memo:
Items followed by “..” are items that have a
submenu.
5. Select the item in the same manner as in
step
3 .
6. Press the PAN/TILT control lever to the left
or to the right to change the set value of the
selected item.
●The value will become smaller when the
lever is pressed to the left (§).
●The value will become larger when the le-
ver is pressed to the right (©).
When the set value of an item is changed,
the change mark (∗) shown in the illustra-
tion on the left appears.
Memo:
For details on submenu settings, see the next
and following pages.
7. When changes have been made, press the
MENU button to return to the higher order
menu.
●At this point, “DATA SAVED” is displayed
on the screen for about 3 seconds when
item settings have been changed.
SETUP
CAME A MODE SELECT . .R
CAME A V I DEO ADJUST . .R
VIDE ADJ FOR POSI . .O
TEXT EDIT..
AUTO PATROL SET . .
AUTO PAN SET . .
PANI ALARM SET . .C
FACT RY SETT INGS. .O
Camera SETUP screen
CAM RA MODE SELECTE
V.PH SE 217A
POS . EXT LOC . UP– LT
ALM. EXT SIZE DOUBLET
BLC DIT1. .E
BLC DIT2. .E
Submenu sample screen
CAM RA MODE SELECTE
V.PH SE 217A
POS . EXT LOC . UP–RT
ALM. EXT SIZE DOUBLET
BLC DIT1. .E
BLC DIT2. .E
Change mark
Sample screen after change
SETUP
MENU SET
SPEED
IRIS
AF
FOCUS
ZOOM
OPEN
FAR
TELE CLEAR /HOME
7
4
1
8
0
5
2
9
6
3
ENTER
AUTO
PAN
OPTION
1OPTION 2
CAMERA POSI-
TION
AUTO
PATROL
CLOSE
NEAR
WIDE
AUTO F-1 F-2 F-3
PAN/TILTLENS CAMERA/POSITION
CAMERA POSITION
REMOTE CONTROL UNIT RM-P2580
ALARM
POWER
KEY LOCK
MENU
button SET
button Power switch
on the rear
panel.
PAN/TILT
control
lever
SETUP
POS I I ON SETUP . .T
CAME A . .R
CONT OL UN I T . .R
Item
cursor Submenu
to be
followed
SETUP screen from the remote control
RM-P2580

19
The menu screen flow is as follows. For details, see the pages referred to.
Menu Screen Flow
SETUP
POS I I ON SETUP . .T
CAME A . .R
CONT OL UN I T . .R
CAM RA MODE SELECTE
V.PH SE 217A
POS . EXT LOC . UP– LT
ALM. EXT SIZE DOUBLET
BLC DIT1. .E
BLC DIT2. .E
ADJUEOVID ST FOR POSI
BLC ODE OFFM
W. BA ANCE ATWL
RB G IN 186A
MG G I N 1 9 2A
UTO PATROLA
PATR L1 HOME 10sO
PATR L2 POS1 10sO
PATR L3 POS2 10sO
PATR L4 POS3 10sO
PATR L5 POS4 10sO
PATR L6 POS5 10sO
PATR L7 POS6 10sO
PATR L8 POS7 10sOWDFBW/>ZDOMO
IC APAN LARM SET
DURA ION 10 sT
POLA I TY MAKER
POS I I ON POS1T
MODE A L ARM
CAME A V I DEO ADJUSTR
AGC ODE 10dBM
SUPE AGC OFFR
SHUT ER SPEED 1 / 60T
ENHA CE HIGHN
AV /P AK 8 / 2E
COLO LEVEL 5R
AWC D J US T . .A
TEXT EDIT
CAME A TREX..T
POS I I ONTEXT..T
UTOAPANSET
STAR PO SET. .TSIIONT
RETU N PO SET . .RITIONS
TORYFAC SETT INGS
FACT RY S NOOSETINGT
SETUP
CAME A MODE SELECT . .
..
R
CAME A V I DEO ADJUSTR
VIDE ADJ FOR POSI. .O
TEXT EDIT..
AUTO PATROL SET . .
AUTO PAN SET . .
PANI ALARM SET . .C
FACT RY SETT I NGS . .O
Normal screen
SETUP screen
from the remote control
Camera SETUP screen
ZSee page 20.
CAMERA MODE SELECT screen
(Used for setting functions
separately for each camera.)
ZSee page 23.
VIDEO ADJUST FOR POSI screen
(Used for setting functions related to
the image of each position.)
ZSee page 30.
AUTO PATROL screen
(Used for setting the auto patrol
function for automatic sequential
movement for each camera.)
ZSee page 24.
PANIC ALARM SET screen
(Used for settings related to
the panic alarm input.)
FACTORY SETTINGS screen
(For returning all settings to the default values.)
ZSee page 24.
AUTO PAN SET screen
(Used for settings related to
auto panning.)
ZSee page 28.
TEXT EDIT screen
(Used for setting and editing
character strings superimposed
on the screen.)
ZSee pages 26 to 27.
CAMERA VIDEO ADJUST screen
(Used for settings functions related to
the video image of each camera.)
ZSee page 21.

20
CAMERA MODE SELECT Screen
Item Function Variable Factory
range setting
V. PHASE
POS.TEXT
LOC.
ALM.TEXT
SIZE
BLC EDIT 1
BLC EDIT 2
Used to adjust and align the vertical phase
of the camera body with other cameras
operating in the Line Lock (LL) mode.
Adjust while viewing the monitor screen.
Adjustment is made by tilting the PAN/TILT
control lever to the left or right.
Used to select the location for displaying
position text.
UP-L: Displays the text in the upper
left corner of the screen.
DOWN-L: Displays the text in the lower
left corner of the screen.
UP-C: Displays the text in the center
of the upper part of the screen.
DOWN-C: Displays the text in the center
of the lower part of the screen.
UP-R: Displays the text in the upper
right corner of the screen.
DOWN-R: Displays the text in the lower
right corner of the screen.
Used to select the size of the characters
displayed during ALARM.
Pressing the SET button displays the
screen (BLC EDIT 1 screen) on which the
user can set the backlight compensation
metering area.
Z See “BLC EDIT Screen”on page 25.
Pressing the SET button displays the
screen (BLC EDIT 2 screen) on which the
user can set the backlight compensation
metering area.
Z See “BLC EDIT Screen”on page 25.
Changing Camera Settings Using the RM-P2580
0 to 255
UP-L
DOWN-L
UP-C
DOWN-C
UP-R
DOWN-R
NORMAL
DOUBLE
127
UP-L
DOUBLE
NORMAL DOUBLE
ALARM
ALARM
Used for setting functions separately for each camera.