JVC TK-C1480E User manual

MNEU SETTING
1
TK-C1480E
1/2" HIGH RESOLUTION COLOUR VIDEO CAMERA
Product Guide
Super LoLux
0.4 lux
TK-C1480Manual.xprNew01.10.295:27PMページ1

New TK-C1480E series
When JVC introduced its TK-1280E series and TK-C1380E series to the 1/2" camera market,
they are widely accepted and recognized as standard-setting cameras.
The new TK-C1480E series, which is to maintain market leadership, adopts newly developed
DSP and CCDs, which feature much higher sensitivity, as well as more functions than its
predecessor, the TK-C1380E series. Added functions include: backlighting and remote
surveillance with RS-422A/RS-485 communications.
Features
Using the 1/2-inch EXVIEW CCD permits sensitivities of 0.8 lux (F 1.2, 50%) and 0.4 lux (F
1.2, 25%). When combined with the slow shutter function, these are increased to 0.025 lux (F
1.2, 50%) and 0.0125 lux (F 1.2, 25%), respectively.
Until now it has been difficult to clearly distinguish between bright and dark subjects in the
same view. With the introduction of JVC’s newly developed DSP this shortcoming no longer
exists, making 24-hour surveillance possible.
For remote camera parameter setting in repeat surveillance communication, RS-422A/
RS-485 standards are provided. An easy-to-use parameter setup menu and high-quality
shooting with no backlight, both of which are popular functions of the TK-C1380E, are also
adopted by the new series.
1/2" IT 440,000-Pixel CCD
Super LoLux
480 TV Lines
S/N 50dB
ExDr (Extended Dynamic Range function)
Motion Detection
RS-422A/RS-485 Communication
Auto Black ON/OFF
Slow Shutter for High Sensitivity
It’s Able to Control by RM-P2580
1
CONCEPT
TK-C1480Manual.xprNew01.10.295:27PMページ1

Super LoLux Sensitivity
Using a new high-sensitivity CCD
permits Super LoLux photography.
TK-C1380E TK-C1480E
0.95 lux, 25% 0.4 lux, 25%
2.0 lux, 50% 0.8 lux, 50%
0.025 lux (50% at slow shutter x32)
0.0125 lux (25% at slow shutter x32)
Spectral Response
TK-C1380E (Conventional CCD) TK-C1480E (EXVIEW CCD)
Because there is a difference in the spectral response of the CCD between TK-C1380E and TK-C1480E, the
same color reproduction is difficult to obtain. (Of course, we have tried to adjust the color matrix of the
TK-C1480E so that it is as close as possible to that of TK-C1380E.)
2
DETAILED FEATURES
1.0
0.8
0.6
0.4
0.2
0.0
400 450 500 550 600 650 700
Cy
Ye
G
Mg
Wave Length (nm)
1.0
0.8
0.6
0.4
0.2
0.0
400 450 500 550 600 650 700
Cy
Ye
G
Mg
Wave Length (nm)
Relative Response
TK-C1480Manual.xprNew01.10.295:27PMページ2

ExDr
ExDr mode: This is the shutter mode for a subject for which strong light and normal (or low) light conditions
coexist.
The ExDr mode is divided into two further modes:
Manual ExDr mode and Auto ExDr mode.
1Manual ExDr mode:
Selectable high speed shutter
1/500 to 1/20,000
Other Competitors style: Fixed
Variable contrast level
+5 to -5
Minus (-) direction: The iris is set at strong light.
Plus (+) direction: The iris is set at low light.
Other Competitors style: Auto only
2Auto ExDr mode:
The iris at the strong light portion and at the low light portion can be automatically detected and the results are
combined to determine the required shutter speed.
Variable contrast level
+5 to -5
Minus (-) direction: Adjusted for strong light
Plus (+) direction: Adjusted for low light
3
DETAILED FEATURES
48 area
Auto peak detect →auto shutter
TK-C1480Manual.xprNew01.10.295:27PMページ3

JVC's positioning compared to competing companies
4
JVC TYPE (ExDr)
EXPANDABILITY SYSTEMS
CCD: SELECT ANY CHIP FROM MARKET
DSP & SOFTWARE: JVC EXCLUSIVE DSP & SOFTWARE
ANY CHIP FROM MARKET
e.g. able to use high
performance CCD like EXVIEW
EXCLUSIVE JVC ORIGINAL
DSP AND SOFTWARE SYSTEMS
&
OTHER MANUFACTURERS’ TYPE
CLOSED CIRCUIT SYSTEMS
CCD: EXCLUSIVE CCD
DSP & SOFTWARE: EXCLUSIVE DSP & SOFTWARE
EXCLUSIVE CCD
HYPER PROGRESSIVE
EXCLUSIVE DSP
AND SOFTWARE SYSTEMS
&
TK-C1480Manual.xprNew01.10.295:27PMページ4

5
DETAILED FEATURES
DIFFERENCE BETWEEN OTHER MANUFACTURER AND JVC TYPE FOR WIDE-DYNAMIC RANGE
HIGH LIGHT SHUTTER
NORMAL LIHGT SHUTTER
1. OTHER MANUFACTURER STYLE (PAL)
Normal Shutter Normal Shutter
For WIDE-Dynamic range function CCD : EXCLUSIVE HYPER PROGESSIVE CCD DSP : EXCLUSIVE PROCESSING
1/50 (FIX)
1/50 (FIX)
1/50 (FIX)
1/100 (FIX)
1/100 (FIX)
1/100 (FIX)
1/4000 (FIX)
1/4000 (FIX)
1/4000 (FIX)
2. JVC STYLE (PAL)
MERIT : better S/N level DEMERIT : reduce the sensitity(reduce the graduation) PAL long shutter : 1/100(FIX) auto 1/10000 manual 1/20000
MANUAL ADJUST POSSIBLE !!
MANUAL ADJUST POSSIBLE !!
MANUAL ADJUST POSSIBLE !!
x 2times reading x 2times reading x 2times reading
For WIDE-Dynamic range function CCD : USE ANY CCD FROM MARKET(JVC USES EXVIEW) DSP : EXCLUSIVE PROCESSING
1/50 1/50 1/501/50
MERIT : keep sensitivity(better graduation) DEMERIT : AGC changeable based on the condition and if it has high light object, it has noisy picture(S/N)
mixed picture output under 1/60 shutter with Gain control
mixed picture output under 1/60 shutter with Gain control
mixed picture output under 1/60 shutter with Gain control
A path B path 2 path reading x2times reading
A path B path 2 path reading x2times reading
A path B path 2 path reading x2times reading
1/50 1/50 1/50 1/50
Variable (Auto & manual)
Variable (Auto & manual)
Variable (Auto & manual)
RAM (MEMORY)
RAM (MEMORY)
RAM (MEMORY)
MIXED PICTURE OUTPUT WITH 1/60 SHUTTER
MIXED PICTURE OUTPUT WITH 1/60 SHUTTER
MIXED PICTURE OUTPUT WITH 1/60 SHUTTER
MIXED PICTURE OUTPUT WITH 1/60 SHUTTER
MIXED PICTURE OUTPUT WITH 1/60 SHUTTER
MIXED PICTURE OUTPUT WITH 1/60 SHUTTER
TK-C1480Manual.xprNew01.10.295:27PMページ5

High-speed side shutter operation for ExDr-AUTO
(Note) Slow shutter mode is not available for WD-ON and manual operation.
Auto Exdr, Auto and Normal modes are available for Sense Up operation.
Manual Exdr and Manual modes are not available for Sense Up operation.
6
SHUTTER LENS
Sees the highest peak on
the divided-by-48 portion.
Adjusts (and sets) the
shutter so that the peak
value may become a
certain level.
Too bright
as a whole
Stops down
the lens
Too dark
as a whole
Opens
the lens
Simultaneous operation
Lowers the high-speed
side shutter speed
(down to 1/100 second)
When the lens is fully
open because the area is
too dark as a whole.
Automatic
If still too dark for a speed
of 1/100 second, then WD
is set to OFF (WD-AUTO).
And at a speed of 1/50
second AGC is turned ON.
(Auto Iris Operation)
TK-C1480Manual.xprNew01.10.295:27PMページ6

Contrast MIX method (or Contrast Mixing)
Level on the Menu shows the value of changing (A).
+5 565mV 80%
+4 540mV 77%
+3 515mV 74%
+2 490mV 70%
+1 465mV 66%
normal 440mV 63%
-1 415mV 59%
-2 390mV 56%
-3 365mV 52%
-4 340mV 49%
-5 315mV 45%
*A place where low brightness is detected
7
DETAILED FEATURES
200%
100%
Low
brightness
side
(Long
Shutter)
High
brightness
side
(Short
Shutter)
Input
Output
200%
100%
Input
Output
200%
100%
Input
Output
200%
100%
Input
Output
200%
100%
Input
Output
200%
100%
Input
Output
+
A
A
Compression
Compressed
to 1/2
High
Low
High
Low
MIX
This is multiplied
by the gamma and
the knee.
Contrast
level
adjust (or
adj.)
menu on
the Menu
TK-C1480Manual.xprNew01.10.295:27PMページ7

Slow Shutter
Available (selectable) modes are: Off, x2, x4, x8, x16, x24 and x32. The same picture is stored in multiple fields
to obtain increased sensitivity.
In this case a decrease of resolution of 50% results when only even fields are used (odd fields are not used).
P.S. Priority Mode
The slow shutter speed can be used when AGC is ON.
1Motion
AGC is turned ON first, followed by slow shutter-ON.
(Motion picture priority mode)
2Picture
If AGC is turned ON first, noise tends to be introduced.
To prevent noise slow shutter is turned ON prior to turning AGC ON. If, however, the prime requirement is
sensitivity, AGC is turned ON first (with no consideration given to increased noise).
8
TK-C1480Manual.xprNew01.10.295:27PMページ8

Motion Detect
9
DETAILED FEATURES
It is possible to set freely the area where MOTION DETECTING functions.
TIMO ON DET ECT
MO E OFFD
LE EL NORMALV
AR A EDI TE
AL RMTI EM10sA
DE ONSTRAT I N
O
M..
..
MOTION DETECT screen
flash
lights gray flash
Setting screen
1. Select the item AREA EDIT on
the MOTION DETECT screen.
2. Press the SET button.
The setting screen is brought up.
3. Select the area not subject to
detection using the
button.
The area flashing ON and OFF in black
and white moves.
4. Press the SET button.
The area not subject to detection is set,
and it turns gray (lights up).
To cancel the set area, press the SET
button again.
5. Repeat items 3 and 4 above.
6. Upon completion of setting,
press the MENU button.
The screen returns to the MOTION
DETECT menu.
MEMO
Indicated positions on the screen are rough
guides.
Be sure to check and conform the positions
on the actual screen.
*It is possible to check and confirm the set
areas on the DEMONSTRATION screen.
The detection area is shown in gray.
TK-C1480Manual.xprNew01.10.295:27PMページ9

Communication
Communication complies with RS-422A/RS-485 standards.
Setup menu is given below.
Main menu  Communication menu
Be sure to make the necessary settings prior to connection.
10
MENU
SYNC ADJUST
VIDEO ADJUST
MODE ESLECT
ALC SETT I NGS
COMMUNI CAT I ON
FACTORY SETT I NGS
MOT I ON DETECT
SYNC DAJUST
VPHASE 0
HPHASE 0
SC ECOARS 0 
SC F INE 128
DEVI O ADJUST
WH TE BAL E ATWNC
A
I
CO OUR LE NORMALEL
V
L
EN ANCE LE NORMALEL
V
H
PE ESTAL LE NORMALEL
V
D
AU OBLACK OFFTL
C
T
TIMO ON DETEC T
MO E OFFD
LE EL NORMALV
AR A EDIE
AL RMTI EM10sA
DE ONSTRAT IN
O
M
CTFA ORY SE NGSTT I
CA CELN
CL A WI
(HOUT T I TLE )RTE
C
DATA CLEARED
LA()RALLE
WH I T E BALANCE CONTROL
AWC SE T . .
RB
::
MG
::
g
LACSETTINGS
IIRSLEVEL NORMAL
AEVRAEG:PEAK 82:
ACGMODE 2dB0
SUTHTERExDR)(NRMALO
PIORRITY –––
BCLOFF
SNSEEUP OFF
MODE SELECT
CAMERA T I TLE ED I T . .
REVERSE MODE OFF
ALM .T I TLE S Z E IDOUBLE
ALARM COLOUR WHITE
MMCO UNICAT ION
ST LE M.DROPY
MA H NE DII 1C
SHUTT RE(ExDR)
SHUTTER SPEED
SPEED
1120/
–––
–––
–––
FAST LIMIT
ED
xER
ED
xR
LLEV
M.
CAMERA T ITLE
’
ÄÖ ÂÊ Î ÔÛÇÑ
äëïöüâê îô
Üûáéíó
àèìòùçñß¡¿ ú
0123456789 :-/ .,
ABCDE KLMNOPFGHI J
QRS TUVWXY Z
abcde klmnopfghi j
qrstuvwxyz
TDislayitle
..
..
..
..
..
....
..
T..
WIDE TELE
TK-C1480Manual.xprNew01.10.295:27PMページ10

Connect cables as shown below.
A RX +
B RX
C TX +
D TX
TX+ A
TX B
RX+ C
RX D
TX+ A
TX B
RX+ C
RX D
RM-P2580
Camera 2
control signal
connection terminals
Connect:
CameraTX+ to RM-P2580E RX+
CameraTX– to RM-P2580E RX–
Camera RX+ to RM-P2580E TX+
Camera RX– to RM-P2580E TX–
The ABCDmarks indicated on both the
camera terminals and the RM-P2580E ter-
minals facilitate correct connections.Connect
the terminals with identical marks.
Connecting the control signal cable
(Use a twisted-pair cable for connection. )
Camera 1
control signal
connection terminals
CAMERA
SETUP
SET
MENU EXT TERM-OFF
INT/GL
DUPLEX
RX TERM-OFF
NOT USED
ON
LL
SIMPLEX
ON
EXT TERM-OFF
INT/GL
DUPLEX
RX TERM-OFF
NOT USED
ON
LL
SIMPLEX
ON
VIDEO
DC
IRIS
AWC
Setting the switches Select the synchronization method of the
camera image.
Set the switch on all cameras to LL (Line Lock)
and match with the V. PHASE.
Set this switch to the DUPLEX
*If the setting is changed, be absolutely sure to
switch on the power again.
Set this switch to ON (signal termination ON)
only on the camera placed at the end of the
control signal cable.
Set to OFF on all other cameras.
Setting on the MENU screen
* If the setting is changed, escape from the menu screen once, and definitely switch on the power again.
MACHINE ID setting switches
Set this item to match the RM-P2580E VIDEO
INPUT terminal number for each camera.
When connecting
●Turn OFF the power supply to all equipment to be used before making connections.
●Carefully read the Instructions for each piece of equipment to be used before making
connections.
●For the appropriate connection cables and the length of these, carefully read “Connections on
the back” on page 16 of Instruction Manual.
●The control signal cable cannot be used for loop connection.
Set to M.DROP
Set to M.DROP when the RM-P2580E is used
as a remote control unit. When controlling from
another machine, make sure that it matches
the communication system used.
MMCO UNICATION
ST LE M.

DROPY
MA H NE DII 1C
RM-P2580E
11
DETAILED FEATURES
TK-C1480Manual.xprNew01.10.295:27PMページ11

Auto Black
Using the Auto Black function the pedestal level can be controlled automatically when AGC is turned ON.
Auto Black Operation (or Control) (ON)
Changes the SET UP (default of pedestal) position in accordance with the AGC gain.
The SET UP position stays at +5 (100 mV approx.) for a PEDESTAL-on-the-MENU of +5 (Max.) irrespective of
the AGC, while it varies from -5 (0 mV) to +5 (100 mV) in accordance with the AGC gain for a PEDESTAL-on-
the-MENU of -5.
12
100mV
50mV
0mV
0dB 10dB 20dB AGC Gain
Pedestal
Level
Pedestal = -5
Pedestal = 0
Pedestal = +5
The thick line indicates the default (set at factory)
Pedestal Setting (Pedestal = 0) + AGC ON (GAIN = 20dB).
TK-C1480Manual.xprNew01.10.295:27PMページ12

White Balance Adjustment
Two white balance modes available to use by TK-C1480.
1. ATW - Automatice White Balance (Auto mode)
Always white balance traced depending on the colour temperature
2. AWC - Automatice White Balance control (one push mode)
It's able to have white balance each object scene. Also sometimes there might be not able to have white
balance with ATW. Such case, please use AWC.
After that, manual painting possible (2Axis) with set up by user.
In addition, AWC is possible by pushing set button (apx.2sec) on the side switches of camera.
13
DETAILED FEATURES
WH I TE BALANCE CONTROL
AT W AWCor
WH I TE BALANCE CONTROL
AWC SE T. .
RB
::
MG
::
g
TK-C1480Manual.xprNew01.10.295:27PMページ13

SPECIFICATION TK-C1380E TK-C1480E/1481EG
Image Sensor 1/2" 1/2" Super LoLux Type
Number of Pixels 752 (H) x 582 (V) 752 (H) x 582 (V)
Video S/N Ratio 48dB (AGC OFF) 50dB (50%, AGC OFF)
Minimum Illuminations 2.0 lux (50% F1.2 AGC ON) 0.8 lux (50% F1.2 AGC ON)
0.95 lux (25% F1.2 AGC ON) 0.4 lux (25% F1.2 AGC ON)
Sync Method Internal Internal
Line-Lock Line-Lock
Full Genlock Full Genlock
L.Lock Phase Adjust YES YES
H Phase Adjust YES YES
SC Phase Adjust YES YES
Horizontal Resolution 470 TV Lines 480 TV Lines
Video Output Composite video signal Composite video signal
Y/C Output YES YES
White Balance ATW ATW
MANUAL AWC (Paint possible)
AGC OFF/9dB/18dB/Super AGC OFF/10dB/20dB/Super AGC
BLC ON/OFF 6 patterns (2 edits) ON/OFF 6 patterns (2 edits)
AES 1/50 — 1/100,000 sec. 1/50 — 1/100,000 sec.
(ON/OFF switchable) (ON/OFF switchable)
Electronic Shutter 1/100, 1/250, 1/500, 1/1,000, 1/100, 1/250, 1/500, 1/1,000,
1/2,000, 1/4,000, 1/10,000 sec. 1/2,000, 1/4,000, 1/10,000 sec.
Camera ID 24 characters 24 characters
Set-Up Menu ENHANCE, IRIS, COLOUR, HUE, ENHANCE, IRIS, COLOUR,
PEDESTAL, Av:Pk Levels PEDESTAL, Av:Pk Levels
Wide Dynamic NO YES
Dynamic Range 200X (Max. at Auto)
400X (Max. at Manual)
Digital Zoom NO NO
Slow Shutter NO YES (Max.: X32)
IR ON/OFF NO NO
Communication NO YES (RS-422A/RS-485 by menu)
Lens Video iris (rear) Video iris (side 4-pin switch)
DC iris (side) DC iris (side 4-pin switch)
Lens Mount C/CS mount C/CS mount
Ambient Temperature -10°C to 50°C (operation) -10°C to 50°C (operation)
0C° to 40°C (recommend) 0C° to 40°C (recommend)
Ambient Humidity Less than 90% Less than 90%
Weight 640g 580g
Power Requirement DC12V/AC24V/AC230V DC12V/AC24V/AC230V (1481EG)
Dimensions (H x W x L) 67 x 70 x 148 mm 63 x 70 x 138 mm
14
COMPARISON
TK-C1480Manual.xprNew01.10.295:27PMページ14

Dimensions (Unit: mm)
15
COMPARISON
TK-C1380E TK-C1480E
COLOR VIDEO CAMERA
BF LOCK
DIGITAL
70
42
71
138
149
35
55
63
U1-32
1/4-20 UNC
41
70
55 1.5
148
159
TK-C1480Manual.xprNew01.10.295:27PMページ15

16
1Camera Mounting Holes (1/4-inch)
Use one of these threaded holes when mounting the
camera on a mount or turret. Two threaded holes are
provided on the front and rear and can be selected
according to the circumstance.
2Camera Mounting Bracket Locking Screws (x3:
M2.6x5mm)
Do not use any screw longer than 5 mm.
3Camera Mounting Bracket
The bracket has been attached on the bottom of the
cameras before shipment. It can also be attached on the
top according to the circumstance.
To re-attach the bracket use the threaded holes at the
top, with the 3 camera mounting bracket locking screw
2.
4Backfocus Adjustment Ring
This ring both allows the adjustment of the backfocus to
and switch as the lens mounting method C and CS.
Loosen the BF LOCK screw 5 by turning it
counterclockwise before turning this ring, and be sure to
secure screw 5 by turning it clockwise after turning this
ring. The TK-C1380/TK-C1381 has been adjusted to the
optimum position for the C mount before shipment.
5[BF LOCK] Backfocus Locking Screw
This screw locks the backfocus adjustment mechanism.
CONTROLS, CONNECTORS AND INDICATORS
1
Lens Mount
This means to attach the lens.
This is applicable to both the C-mount lenses (1/2 inch)
and CS-mount lenses (1/2 inch).
2
Backfocus Adjustment Ring
Adjusting the back focus during lens installation.
When readjustment is required, loosen the locking
screw
3
by turning it counterclockwise and turn the
back focus adjustment ring
2
.
After the adjustment, tighten the locking screw
3
again.
The TK-C1480 has been adjusted to the optimum
position for the C-mount system before shipment.
3
[BF LOCK] Back Focus Locking Screw
This serves to fix the back focus-adjusting ring.
4
Camera-Mounting Bracket
The bracket has been attached on the bottom of the
camera before shipment. It can also be attached on
the top according to the circumstance.
To re-attach the bracket use the threaded holes at the
top, with the camera mounting bracket locking screws
7
.
5
Camera-Mounting Screw Hole (1/4 inch)
Use this hole when mounting the camera
onto a fixer, pan/tilt unit, and the like. (Use a
screw shorter than 7 mm.)
6
Rotation-Preventive Hole
Make use of this rotation-preventive hole to prevent
any fall when mounting the camera. Make sure that
the camera is securely mounted.
7
Camera Mounting Bracket Fixing Screws (×2: M2.6
×5 mm)
Do not use any screws longer than 5 mm.
1
2
34
5
6
7
MAX.
7 mm
TK-C1380E TK-C1480E
TK-C1480Manual.xprNew01.10.295:27PMページ16

17
6Lens Mount
The lens mount is compatible with C-mount lenses (1/2
and 2/3 inches) and CS-mount lenses (1/2-inch).
7[DC IRIS] DC Iris Connector
Connect to an auto-iris lens which does not incorporate
an EE amplifier.
CONTROLS, CONNECTORS AND INDICATORS
TK-C1380E TK-C1480E
ON
SIMPLEX
ON

LL
SET
AWC
MENU
CAMERA
SETUP
EXTTERM-OFF
INT/GL
DUPLEX
RXTERM-OFF
NOT USED
VIDEO
DC
IRIS
!@# $
%
^
&
*
890
8Cover
The cover opens if it is pulled to the left while being
pushed.
9[VIDEO/DC] Iris Selector Switch
This is set according to the type of lens when an
automatic iris control lens is used.
VIDEO: In case of lens with EE amp built-in.
DC: In case of lens without EE amp built-in.
(VIDEO: At time of factory shipment)
10
[IRIS] IrisTerminal
This is connected to an automatic iris control lens.
11
[MENU] Menu Button
When the button is pressed, a menu screen is brought
up.
12
[SET/AWC] Set. Auto White Control Button
SET: Press this button to display a sub-menu.
AWC: If this button is kept pressed for more than 1
second, a one-push-auto-white-balance
function works and sets the white balance.
Once it is set, even if colour temperature
changes, white balance does not change. It is
also possible to make fine adjustments on the
set white balance.
13
[, , , ] Up-and-Down,Left-and-Right Button
These buttons select items on the menu screen and
change a set value.
14
[EXT.TERM-ON/OFF] Terminal On/Off Switch of
External Synchronization Signal
This is a terminating ON/OFF switch for the external
synchronization input signal.
When this is switched ON, termination is executed via
a 75 Ωresistor.
ON: terminates at 75Ω.
OFF: does not terminate at 75Ω.
(ON: At time of factory shipment)
These functions such as !$of TK-C1480E
are not available on TK-C1380E.
TK-C1480Manual.xprNew01.10.295:27PMページ17

18
8[SYNC IN] Sync Signal Input Connector
This BNC connector accepts the input of an external
sync signal such as a composite video (VBS) or black
burst (BB) signal. When a sync signal is input into this
connector, the camera operation is automatically
synchronized with the external sync signal.
The 75-ohm termination of this connector can be
switched on/off on the menu screen as required.
9[VIDEO OUT] Video Signal Output Connector
This BNC connector outputs a composite video signal.
Connect this to the video input connector of a video
mounter, switcher, etc.
0[POWER] Power Indicator Lamp
This lights when power is supplied to the camera.
.
15
[INT/GL, LL] Selector Switch for Synchronizing
System
This switch can set a synchronizing system of the
camera.
INT/GL:
This is set for internal synchronization (INT) or external
synchronization (GL).
LL (Line Lock):
The camera’s vertical synchronization is locked to the
AC 24V power line frequency.
When switching between multiple cameras using a
switcher, selecting this mode and adjusting the vertical
phase can reduce the monitor sync disturbances
occurring when the camera image is switched. (This
cannot be used in regions where the power frequency is
50 Hz.) (INT/GL: At time of factory shipment)
16
[DUPLEX, SIMPLEX] Selector Switch for
Transmission System
If the setting is changed, be absolutely sure to switch
on the power again.
DUPLEX:
This switch sets to DUPLEX when the transmission
between the camera and a remote control unit is in a
duplex system (two-way).
SIMPLEX:
This switch sets to SIMPLEX when the transmission
between the camera and a remote control unit is in a
simplex system (one-way).
(DUPLEX: At time of factory shipment)
17
[RX.TERM-ON/OFF] RX Signal Terminal ON/OFF
Switch
This sets whether or not the signal between RX + and
RX – on the back
20
should be terminated at the value
of 110Ωresistance.
ON: terminates.
OFF: does not terminate.
If the system including the camera is the M.DROP
(Multi-drop, RS-485) system, only the camera mounted
at the terminal of control signal cable is set to “ON”
and the other camera is set to “OFF”. In case of the
M.DROP system, it becomes necessary to set the
Machine ID.
If the system including the camera is the P TO P (Point
to Point, RS-422A) system, set this switch of all the
cameras to “ON”.
The item STYLE on the COMMUNICA-TION screen
sets M.DROP or P TO P
(ON: At time of factory shipment)
18
NOT USED
This cannot be used. Do not switch.
TK-C1380E TK-C1480E
TK-C1480Manual.xprNew01.10.295:27PMページ18

19
![Y/C OUT] Y/C Output Connector
This 4-pin connector outputs the luminance and
chrominance signal.
Pin configuration of Y/C OUT connector
@[CAMERA SET UP] Camera Set-up Screen
Operation buttons
These buttons are used in the set-up operations.
#[VIDEO IRIS] Video Iris Connector
Connect to an auto-iris lens incorporating an EE
amplifier.
$[DC12V/AC24V] Power Input Connector
(TK-C1380E only)
Connect a DC 12 V±10% or AC 24 v±10%, 50/60 Hz
power supply.
%Power Cable (for TK-C1381EG only)
Connect to the commercial AC 230V outlet
CONTROLS, CONNECTORS AND INDICATORS
DC12
AC24
/C
C I
E
IDE
EE I
CI
MA A
1 2
CA 2( E)
IAED E (E E)
AGD
ABCD
)(
t
r
e
w
q
19
[DC 12V, AC 24V] Power InputTerminals
To input DC 12V or AC 24V power.
20
[TX+A, TX-B, RX+C, RX-D] Control Signal
ConnectionTerminals
Terminals for inputting signals with electrical
characteristics conforming to the EIA/TIA RS-422A or
RS-485 standard.

17
RX.TERM switch
21
[AUX, GND] Auxiliary OutputTerminals
If any change occurs in the area that was set on the
MOTION DETECT screen, these terminals output
signals. Open collector output of a LOW pulse for
between 500 ms and 1,000 ms. Max voltage 30V,
current 30 mA.
22
[Y/C OUT]Y/C Output Connector
This 4-pin connector outputs the luminance and
chrominance signal.
•Pin configuration ofY/C OUT connector
23
[VIDEO OUT] Video Signal Output Connector
This BNC connector outputs a composite video signal.
Connect this to the video input connector of a video
monitor, switcher, etc.
24
[POWER] Power Indicator Lamp
This lamp lights when power is supplied to the camera.
25
[SYNC IN] Sync Signal Input Connector
This BNC connector accepts the input of an external
sync signal such as a composite video (VBS) or black
burst (BB) signal.
When a sync signal is input into this connector, the
camera operation is automatically synchronized with
the external sync signal.
To terminate this connector at 75Ω, turn ON the
EXT.TERM switch
14
.
4
2
3
1
Pin No. Signal
1GND
2GND
3Luminance (Y, 1 V(p-p), 75Ω)
4Chrominance (C, 0.3 V(p-p), 75Ω)
TK-C1380E TK-C1480E
TK-C1480Manual.xprNew01.10.295:27PMページ19