JVC GR-D390UC /connections Guide

SOFTWARE INSTALLATION AND
USB CONNECTION GUIDE
ENGLISH
Filename [M6D1_01Cov.fm]
LYT1532-002A EN
M6D1.book Page 1 Thursday, June 29, 2006 12:06 PM

Master Page: Left
JVC SOFTWARE LICENSE AGREEMENT..
.................................................................. 3
Notice for Users............................................ 5
System Requirements .................................. 6
Software Installation (Windows®).................. 7
Connections (Windows®) .............................. 9
Viewing the Contents of a Memory Card
(Windows®) .............................................. 10
Copying Files to the PC (Windows®) ........... 11
Playing Back Files on the PC (Windows®)... 11
Disconnecting the USB Cable (Windows®).. 12
Connections (Macintosh)............................. 13
Viewing the Contents of a Memory Card
(Macintosh).............................................. 14
Copying Files to the PC (Macintosh) ........... 15
Playing Back Files on the PC (Macintosh)... 15
Disconnecting the USB cable (Macintosh) .. 16
User’s Guide/Help/Readme (Windows®) ..... 16
Overview of Enjoying the Moving or Still
Images on the PC.................................... 17
Contents
M6D1.book Page 2 Thursday, June 29, 2006 12:06 PM

—3—
Master Page: Cov
JVC SOFTWARE LICENSE
AGREEMENT
The right to use the Program is granted by
Victor Company of Japan, Limited (“JVC”)
to You only on the condition that You agree
to the following.
Should You not agree to the terms hereof,
You may not install or use the Program.
HOWEVER, INSTALLING OR USING THE
PROGRAM INDICATES YOUR
ACCEPTANCE OF THESE TERMS AND
CONDITIONS.
1COPYRIGHT; OWNERSHIP
You acknowledge that all copyrights and
other intellectual property rights in the
Program are owned by JVC and its
licensor, and remain vested in JVC and
such licensor. The Program is protected
under the copyright law of Japan and
other countries, and related
Conventions.
2GRANT OF LICENSE
(1) Subject to the conditions of this
Agreement, JVC grants to You a non-
exclusive right to use the Program.
You may install and use the Program
on a HDD or other storage devices
incorporated in Your PC.
(2) You may make one (1) copy of the
Program solely for your personal
backup or archival purposes.
3RESTRICTION ON THE
PROGRAM
(1) You may not reverse engineer,
decompile, disassemble, revise or
modify the Program, except to the
extent that expressly permitted by
applicable law.
(2) You may not copy or use the
Program, in whole or in part, other
than as expressly specified in this
Agreement.
(3) You have no right to grant a license to
use the Program, and may not
distribute, rent, lease or transfer the
Program to any third party or
otherwise let them use the Program.
4LIMITED WARRANTY
JVC warrants that any media in which
the Program is embodied are free from
any defects in materials and
workmanship for a period of thirty (30)
days from the date of Your purchasing
any our products accompanying the
Program. JVC’s entire liability and your
exclusive remedy in connection with the
Program shall be replacement of such
defective media. EXCEPT FOR THE
EXPRESS WARRANTIES STATED
HEREIN AND TO THE EXTENT
PERMITTED BY APPLICABLE LAW,
JVC AND ITS LICENSORS DISCLAIM
ANY OTHER WARRANTIES, EITHER
EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO IMPLIED
WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR
PURPOSE IN REGARD TO THE
PROGRAM AND THE
ACCOMPANYING PRINTED
MATERIALS. SHOULD THERE BE ANY
PROBLEM ARISING FROM OR
CAUSED BY THE PROGRAM, YOU
SHOULD SETTLE ALL SUCH
PROBLEM AT YOUR OWN COST AND
EXPENSE.
IMPORTANT
TO CUSTOMERS: PLEASE MAKE
SURE TO READ THIS CAREFULLY
BEFORE INSTALLING OR USING THE
SOFTWARE PROGRAM NAMED
“DIGITAL PHOTO NAVIGATOR”
(“Program”) ON YOUR PC.
CONTINUED ON NEXT PAGE
M6D1.book Page 3 Thursday, June 29, 2006 12:06 PM

—4—
Master Page: Left
5LIMITED LIABILITY
TO THE EXTENT PERMITTED BY
APPLICABLE LAW, IN NO EVENT
SHALL JVC AND ITS LICENSORS BE
LIABLE FOR ANY INDIRECT,
SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES
WHATSOEVER, REGARDLESS OF
THE FORM OF ACTION WHETHER IN
CONTRACT, TORT OR OTHERWISE
ARISING OUT OF OR IN
CONNECTION WITH THE USE OF OR
INABILITY TO USE THE PROGRAM,
EVEN IF JVC HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH
DAMAGES. YOU WILL INDEMNIFY
AND HOLD HARMLESS JVC FROM
ANY LOSS, LIABILITY OR COST
ARISING OUT OF OR IN ANY WAY
CONNECTED TO CLAIMS FROM ANY
THIRD PARTY RELATING TO THE USE
OF THE PROGRAM.
6TERM
This Agreement will become effective on
the date when You install and use the
Program on Your machine, and continue
to be in effect until the termination under
the following provision.
Should You breach any provision of this
Agreement, JVC may terminate this
Agreement without giving any notice to
You. In this event, JVC may claim
against You for any damages caused by
Your breach. Should this Agreement be
terminated, You must immediately
destroy the Program stored in Your
machine (including the erasing from any
memory in Your PC), and no longer own
such Program.
7EXPORT CONTROL
You agree that You will not ship, transfer
or export the Program or underlying
information and technology to any
countries to which Japan and other
relevant countries have initiated an
embargo on such goods.
8U.S. GOVERNMENT USER
If You are an agency of the United
States of America (the “Government”),
You acknowledge JVC’s representation
that the Program is a “Commercial Item”
as defined in Federal Acquisition
Regulation (FAR) part 2.101 (g)
consisting unpublished “Commercial
Computer Software” as those items are
used at FAR part 12.212 and is only
licensed to You with the same use rights
JVC grants all commercial end users
pursuant to the terms of this Agreement.
9GENERAL
(1) No modification, change, addition,
deletion or other alternation of or to
this Agreement will be valid unless
reduced to writing and signed by an
authorized representative of JVC.
(2) If any part of this Agreement is held
invalid by or in conflict with any law
having jurisdiction over this
Agreement, the remaining provisions
will remain in full force and effect.
(3) This Agreement shall be governed by
and interpreted under the laws of
Japan. The Tokyo District Court has
jurisdiction over all disputes which
may arise with respect to the
execution, interpretation and
performance of this Agreement.
Victor Company of Japan, Limited
NOTE:
If You acquired the Program in Germany,
the provisions of Sections 4 (Limited
Warranty) and 5 (Limited Liability) provided
above will be replaced with those of the
German version of this Agreement.
M6D1.book Page 4 Thursday, June 29, 2006 12:06 PM

Master Page: Right
—5—
You can find the latest information (in
English) on the provided software
program at our world wide web server at
http://www.jvc-victor.co.jp/english/
index-e.html
Use of this software is authorized according
to the terms of the software license.
When contacting the nearest JVC office or
agency in your country about this software
(refer to the JVC Worldwide Service
Network at http://www.jvc-victor.co.jp/
english/worldmap/index-e.html), please fill
out the following and have the appropriate
information ready.
Please note that it may take some time to
respond to your questions, depending on
their subject matter.
JVC cannot answer questions regarding
basic operation of your PC, or questions
regarding specifications or performance
of the OS, other applications or drivers.
CyberLink
For details of CyberLink’s technical support
service, refer to the “Readme” of each
software (墌pg. 16) and the following
website: http://www2.cli.co.jp/products/
dvc/
CAUTION:
●Operate this equipment according to
the operating procedures described in
this manual.
●Use only the provided CD-ROM. Never
use any other CD-ROM to run this
software.
●Do not attempt to modify this software.
●Changes or modifications not approved
by JVC could void user’s authority to
operate the equipment.
How to handle a CD-ROM
●Take care not to soil or scratch the
mirror surface (opposite to the printed
surface). Do not write anything or put a
sticker on either the front or back
surface. If the CD-ROM gets dirty,
gently wipe it with a soft cloth outward
from the center hole.
●Do not use conventional disc cleaners
or cleaning spray.
●Do not bend the CD-ROM or touch its
mirror surface.
●Do not store your CD-ROM in a dusty,
hot or humid environment. Keep it away
from direct sunlight.
Notice for Users
Product Name
Model
Problem
Error Message
PC
Manufacturer
Model
□Desktop
□Laptop
CPU
OS
Memory MB
Available Hard
Disk Space MB
M6D1.book Page 5 Thursday, June 29, 2006 12:06 PM

—6—
Master Page: Left
䡲Windows®
The following requirements must be
satisfied to connect a camcorder to a PC
and to use Digital Photo Navigator.
OS: Windows®Millennium Edition (Me)
(pre-installed), Windows®2000 Professional
(2000) (pre-installed), Windows®XP Home
Edition (XP) (pre-installed), or
Windows®XP Professional (XP) (pre-
installed)
CPU: Intel MMXTM Pentium®, at least
200 MHz
RAM: At least 64 MB
Free hard disk space: At least 10 MB for
installation, at least 500 MB recommended
Connector: USB connector
Display: Must be capable of displaying
800 x 600 dots with 16-bit color
Miscellaneous: Internet Explorer 5.5 or
later
For PowerProducer 2 Gold VCD
In addition to the requirements above, the
following requirements must be satisfied to
use PowerProducer 2 Gold VCD.
OS: The same as requirements above.
CPU: Intel Pentium® II, at least 450 MHz,
Intel Pentium®III, at least 800 MHz
recommended
RAM: At least 128 MB, at least 256 MB
recommended
Free hard disk space: At least 100 MB for
installation, at least 1 GB for creating VCD
Connector: IEEE1394 (i.LINK) connector.
Miscellaneous: DirectX 9.0 or later
(DirectX 9.0 is installed automatically),
Internet Explorer 5.5 or later
Supported media: CD-R/RW
Display: Must be capable of displaying
1024 x 600 dots with 16-bit color
For more details, refer to CyberLink web
site:http://www.gocyberlink.com/english/
products/powerproducer/2_gold/
comp_dvd_drives.jsp
䡲Macintosh
The following requirements must be
satisfied to connect a camcorder to a PC.
Hardware: iMac, iBook, Power Mac G4 or
G5, PowerBook G3 or G4, eMac, Mac Mini
equipped with a USB connector
OS: Mac OS X (10.1.5, 10.2.1 to 10.2.8,
10.3.1 to 10.3.9, 10.4.2, 10.4.3)
RAM: At least 128 MB
●The system requirements information
above is not a guarantee that the
provided software will work on all
personal computers meeting those
requirements.
●If your PC does not meet the system
requirements above, you can use the
optional USB reader/writer CU-VUSD70,
the PC card adapter CU-VPSD60 or the
floppy disk adapter CU-VFSD50 to load
the files in the memory card to the hard
disk on your PC.
(Refer to “JVC Accessories” on our world
web site at: http://www.jvc-victor.co.jp/
english/accessory/)
●Windows®is either registered trademarks
or trademarks of Microsoft Corporation in
the United States and/or other countries.
●Macintosh is a registered trademark of
Apple Computer, Inc.
●Other product and company names
included in this instruction manual are
trademarks and/or registered trademarks
of their respective holders.
System Requirements
M6D1.book Page 6 Thursday, June 29, 2006 12:06 PM

Master Page: Right
—7—
Follow the procedure described below to
install the software. From the [SETUP]
screen in step 2, you can install the
following software. Quit any other software
you are using. (Check that there are no
other application icons on the status bar.)
PowerProducer 2 Gold VCD
PowerProducer 2 Gold VCD is software for
creating movie discs incorporating not only
video but also slideshows. This software
uses a simple wizard format for creating a
wide range of different format discs. You
can also edit imported video. You can
import video from the camera, edit it, and
then create a slideshow from still images.
You can create a customized menu for the
video or slideshow and write the contents to
VCD.
Digital Photo Navigator 1.5
This application is used to organize still
images and convert them into a variety of
formats.
1Load the provided CD-ROM into
the PC.
After a moment, the [SETUP] screen
appears.
●From the [SETUP] screen, you can
install the software.
●If the [SETUP] screen does not
appear, double-click the CD-ROM
icon in the [My Computer] window.
2Click [Install] on the right side
of the desired software and
follow the on screen
instructions to complete the
installation.
The installation of the software starts.
The procedure differs depending on
the software.
Following steps are the example of
PowerProducer 2 Gold on
Windows®XP.
[Choose Setup Language] screen
appears.
Select the desired language and click
[OK].
Then, [PowerProducer Setup] screen
appears.
Click [Next].
[License Agreement] screen appears.
Click [Yes].
[Customer Information] screen
appears.
Confirm your information and click
[Next].
●It is possible to change the
information.
Then, [Choose Destination Location]
screen appears.
Software Installation
(Windows®)
CONTINUED ON NEXT PAGE
M6D1.book Page 7 Thursday, June 29, 2006 12:06 PM

—8—
Master Page: Left
Click [Next].
[Select Working Directory] screen
appears.
Click [Next].
Then, [Select Program Folder] screen
appears.
Click [Next].
[Select will install...] screen appears.
Click [Next].
Wait for a moment until the installation
is finished.
When the installation is finished,
[Setup Complete] screen appears.
Click [Finish]. Restarts the PC.
For Windows®Me/2000:
Before [Setup Complete] screen
appears, [Question] screen appears.
Click [Yes]. Then, [DMA setting] screen
appears. Click [OK]. [Setup Complete]
screen appears. Click [Finish] to
restart the PC.
Install Digital Photo Navigator 1.5 in the
same way.
To display [SETUP] screen, double-click the
CD-ROM icon in the [My Computer]
window.
NOTE:
If you perform installation of a software that
is already installed, uninstallation will start.
In this case, perform the installation again
after uninstallation is finished.
M6D1.book Page 8 Thursday, June 29, 2006 12:06 PM

Master Page: Right
—9—
Connecting the USB cable
Connect the USB cable to copy still image files in a memory card to the PC.
Connecting the DV cable
Connect the DV cable to use PowerProducer in capturing video.
1To assure safety, make sure all
units are turned off before
making any connections.
2Use the USB cable or DV cable
to connect the camcorder to the
PC.
NOTES:
●It is recommended to use the AC
Adapter as the power supply instead
of the battery pack.
●When the USB cable or DV cable is
connected, turning on or off the
camcorder or switching the VIDEO/
MEMORY (DSC) mode on the camcorder
causes malfunctions of the PC.
●If PowerProducer does not recognize the
camcorder, exit PowerProducer once,
then start it again.
●If you connect the camcorder to the PC
through a USB hub, compatibility issues
between the hub and the PC may result in
instability in the operation of the PC. If this
happens, connect the camcorder directly
to the PC, not through the hub.
●Do not use an extension USB cable.
●When connecting the camcorder to a PC
using a DV cable, make sure to follow the
procedure below. Connecting the cable
incorrectly may cause malfunctions to the
camcorder and/or the PC.
●Connect the DV cable first to the PC, and
then to the camcorder.
●Connect the DV cable (plugs) correctly
according to the shape of the DV
connector.
Connections (Windows®)
To USB connector PC
To USB connector
USB cable
Camcorder
DV cable (optional)
To DV connector To IEEE1394
connector
M6D1.book Page 9 Thursday, June 29, 2006 12:06 PM

—10—
Master Page: Left
1Make sure that there is a
memory card in the camcorder.
2Set the camcorder’s VIDEO/
MEMORY Switch to “MEMORY”.
3Set the camcorder’s Power
Switch to “PLAY” while
pressing down the Lock Button
located on the switch.
The camcorder turns on.
4Connect the camcorder to the
PC with a USB cable. (墌pg. 9)
On the camcorder’s LCD monitor
[USB] appears.
5WhenusingWindows®XP:
The [Removable
Disk] window
appears on the
PC’s screen
after a moment.
Select [Open
folders to view
files using
Windows
Explorer] and
click [OK].
NOTE:
If the [Removable Disk] window does
not appear, confirm the connection
(墌pg. 9) or perform the steps 1and
2below.
When using Windows®Me/2000:
1Double-click the [My Computer] icon
on the desktop. The [Removable
Disk] icon which represents the
memory card in the camcorder
appears in the [My Computer]
window.
2Double-click the [Removable Disk]
icon.
6The folders in the memory card
appear.
Different file types are stored in
different folders.
[DCIM]: Contains folders with still
images (extension “.jpg”)
[MISC]: Contains folders with DPOF
setting data
NOTES:
●Saving the wrong kinds of files in a
memory card or deleting files or folders
from a memory card can cause problems
with the operation of the camcorder.
When it is necessary to delete a file from
a memory card, delete it through the
camcorder.
●Never disconnect the USB cable while
“ ” is displayed on the
camcorder’s LCD monitor.
●If you are using a brand new memory
card, you need to initialize the memory
card with the camcorder first. You may not
be able to copy files from the memory
card to the PC without doing so.
●The file extension may not appear
depending on the [FOLDER] option
setting of Windows®.
Viewing the Contents of a
Memory Card (Windows®)
DPOF setting data
Still images
M6D1.book Page 10 Thursday, June 29, 2006 12:06 PM

Master Page: Right
—11—
Still image files that are stored in a memory
card can be copied to the PC and played
back on the PC.
1Perform the procedure in
“Viewing the Contents of a
Memory Card (Windows®)”
(墌pg. 10).
The folders in the memory card
appear.
2Create a new folder, enter the
folder name, and then double-
click it.
●For example, create a new folder in
the [My Pictures] folder.
3Select the folder to be copied,
and then drag and drop that
folder in the destination folder.
●To copy still images: Copy the folder
within the [DCIM] folder.
“ ” appears on the LCD
monitor of the camcorder, and the
folder is copied from the memory card
to the PC.
NOTE:
Never disconnect the USB cable while
“ ” is displayed on the camcorder’s
LCD monitor.
Still images
Use an application that can handle the
JPEG file format. To view a still image,
double-click the still image file (extension
“.jpg”).
Copying Files to the PC
(Windows®)
Playing Back Files on the PC
(Windows®)
M6D1.book Page 11 Thursday, June 29, 2006 12:06 PM

—12—
Master Page: Left
Before loading or unloading memory cards
or turning off the PC, first disconnect the
USB cable and turn off the camcorder.
1Confirm that “ ” is not
currently displayed on the LCD
monitor of the camcorder.
●If “ ” is currently displayed,
wait until it disappears before
proceeding.
2Double-
click the
[Safely
Remove Hardware] or [Unplug
or Eject Hardware] icon in the
status bar.
The [Safely Remove Hardware] or
[Unplug or Eject Hardware] dialog box
appears.
Windows® XP: If not, wait a while then
go to step 5.
3Select [USB Mass Storage
Device] or [USB Disk], and then
click [Stop].
●Windows® 2000/XP
●Windows® Me
The [Stop a Hardware device] dialog
box appears.
4Click [OK].
Windows® 2000/Me: If a message
indicating that the device can be safely
removed appears, click [OK] and then
click [Close].
●Windows® 2000/XP
●Windows® Me
*The model name depends on the
connected camcorder.
5Disconnect the USB cable.
6Set the camcorder’s Power
Switch to “OFF”.
The camcorder turns off.
Disconnecting the USB Cable
(Windows®)
M6D1.book Page 12 Thursday, June 29, 2006 12:06 PM

Master Page: Right
—13—
Connect the USB cable to copy still image files in a memory card to the PC.
1To assure safety, make sure all
units are turned off before
making any connections.
2Use the USB cable to connect
the camcorder to the PC.
NOTES:
●It is recommended to use the AC
Adapter as the power supply instead
of the battery pack.
●When the USB cable is connected,
turning on or off the camcorder or
switching the VIDEO/MEMORY (DSC)
mode on the camcorder causes
malfunctions of the PC.
●If you connect the camcorder to the PC
through a USB hub, compatibility issues
between the hub and the PC may result in
instability in the operation of the PC. If this
happens, connect the camcorder directly
to the PC, not through the hub.
●Do not use an extension USB cable.
Connections (Macintosh)
PC
USB cable
Camcorder
To USB
connector To USB connector
M6D1.book Page 13 Thursday, June 29, 2006 12:06 PM

—14—
Master Page: Left
1Make sure that there is a
memory card in the camcorder.
2Set the camcorder’s VIDEO/
MEMORY Switch to “MEMORY”.
3Set the camcorder’s Power
Switch to “PLAY” while
pressing down the Lock Button
located on the switch.
4Connect the camcorder to the
PC with a USB cable. (墌pg. 13)
On the camcorder’s LCD monitor
[USB] appears. The memory card icon
appears on the desktop.
●Depending on the type of OS used,
iPhoto starts if the memory card
contains a DCIM folder.
5Double-click the memory card
icon on the desktop.
The folders in the memory card
appear.
Different file types are stored in
different folders.
[DCIM]: Contains folders with still
images (extension “.jpg”)
[MISC]: Contains folders with DPOF
setting data
NOTES:
●Saving the wrong kinds of files in a
memory card or deleting files or folders
from a memory card can cause problems
with the operation of the camcorder.
When it is necessary to delete a file from
a memory card, delete it through the
camcorder.
●Never disconnect the USB cable while
“ ” is displayed on the
camcorder’s LCD monitor.
●If you are using a brand new memory
card, you need to initialize the memory
card with the camcorder first. You may not
be able to copy files from the memory
card to the PC without doing so.
Viewing the Contents of a
Memory Card (Macintosh)
Still images DPOF Setting data
M6D1.book Page 14 Thursday, June 29, 2006 12:06 PM

Master Page: Right
—15—
Still image files that are stored in a memory
card can be copied to the PC and played
back on the PC.
1Double-click the
memory card icon on
the desktop.
The folders in the memory
card appear.
2Create a new folder, enter the
folder name, and then double-
click it.
3Select the folder to be copied,
and then drag and drop that
folder in the destination folder.
●To copy still images: Copy the folder
within the [DCIM] folder.
“ ” appears on the LCD
monitor of the camcorder, and the
folder is copied from the memory card
to the PC.
NOTE:
Never disconnect the USB cable while
“ ” is displayed on the camcorder’s
LCD monitor.
Still images
Use an application that can handle the
JPEG file format. To view a still image,
either double-click the still image file
(extension “.jpg”), or drag and drop the file
on the application icon.
Copying Files to the PC
(Macintosh) Playing Back Files on the PC (Macintosh)
M6D1.book Page 15 Thursday, June 29, 2006 12:06 PM

—16—
Master Page: Left
Before loading or unloading memory cards
or turning off the PC, first disconnect the
USB cable and turn off the camcorder.
1Drop the memory card
icon on the desktop
into the [Trash] icon.
●If the confirmation
message appears, click
[OK].
2Confirm that
“”isnot
currently displayed on
the LCD monitor of the
camcorder.
●If “ ” is currently displayed,
wait until it disappears before
proceeding.
3Disconnect the USB cable.
4Set the camcorder’s Power
Switch to “OFF”.
The camcorder turns off.
This manual only refers to software
installation and PC connection. For more
details of each software, refer to its user’s
guide/help/Readme.
䡲CyberLink PowerProducer
1Click [Start], go to [All
Programs] or [Programs] –
[CyberLink PowerProducer] –
[PowerProducer Gold], and then
click User’s Guide/Help/Readme
(Windows®) depending on your
preference.
䡲Digital Photo Navigator
●The instruction manual is included on the
CD-ROM in PDF format. Right-click the
CD-ROM icon in [My Computer], then
click [Open]. Double-click the [Docs]
folder. Open the “Start.pdf” file and click
the button of the desired language. Note
that Adobe®Acrobat®ReaderTM or
Adobe®Reader®must be installed to read
PDF files.
●Adobe®Reader®can be loaded from
Adobe’s web site: http://
www.adobe.com/
Disconnecting the USB cable
(Macintosh) User’s Guide/Help/Readme (Windows®)
INFORMATION
The programs in CyberLink
PowerProducer are versions with limited
functionality. The User’s Guide and Help
files are written for the commercial
version available in stores. For
information about the differences with the
commercial version, see the Readme file
for the respective program.
M6D1.book Page 16 Thursday, June 29, 2006 12:06 PM

Master Page: Right
—17—
Overview of Enjoying the Moving or Still Images on the PC
Moving images Still images
TRANSFER the moving
images via the DV cable
Camcorder
SHOOT the moving images
Cassette
PC
EDIT moving images
CREATE the VCD with
PowerProducer 2 Gold VCD
PLAYBACK the VCD
Memory Card
SHOOT the still images
CREATE and ENJOY the
picture album with
Digital Photo Navigator 1.5
TRANSFER the still images
via the USB cable
PC
Use of PowerProducer 2 Gold
VCD alone is enough for
creating a DVD or VCD with
ease.
http://www2.cli.co.jp/
products/dvc/
M6D1.book Page 17 Thursday, June 29, 2006 12:06 PM

Printed in Malaysia
0206ASR-PR-VM
© 2006 Victor Company of Japan, Limited M6D1
SOFTWARE INSTALLATION
AND USB CONNECTION
GUIDE
ENENEN
EN
M6D1.book Page 16 Thursday, June 29, 2006 12:06 PM

GUIDE D’INSTALLATION DU
LOGICIEL ET RACCORDEMENT
D’ORDINATEUR
FRANÇAIS
LYT1532-002A FR

CONTRAT DE LICENCE LOGICIEL JVC..... 3
Notice pour les utilisateurs ........................... 5
Configuration requise ................................... 6
Installation du logiciel (Windows®)................ 7
Connexions (Windows®) ............................... 9
Affichage du contenu d’une carte mémoire
(Windows®) .............................................. 10
Copie des fichiers vers l’ordinateur (Windows®)
................................................................. 11
Lecture de fichiers sur l’ordinateur (Windows®)
................................................................. 11
Déconnexion du câble USB (Windows®) ..... 12
Connexions (Macintosh).............................. 13
Affichage du contenu d’une carte mémoire
(Macintosh).............................................. 14
Copie des fichiers vers l’ordinateur
(Macintosh).............................................. 15
Lecture de fichiers sur l’ordinateur (Windows®)
..................................................................... 15
Déconnexion du câble USB (Macintosh) ..... 16
Guide de l’utilisateur, Aide en ligne et fichier
“Lisez-moi” (Windows®) ........................... 16
Aperçu sur la visualisation d’images en
mouvement ou fixes sur un ordinateur .... 17
TABLE DES MATIÈRES