JYE Tech DSO 150 User manual
1
Plum Audio - DSO 150 EuroScope v2.0 - Build Guide!
Deign by Shay Shezifi
10.02.19
!
Jye Tech DSO 150
Eurorack Conversion Kit MKII
Build Guide
DSO 150 Is a cheap mini oscilloscope from JYE TECH.
This conversion kit lets you the ability to convert it to Eruorack module and contains
two parts:!
- 14 Hp Panel
- Conversion Board
- Optional: Expander 2Hp PCB+Panel
This is an easy DIY project, just follow this instructions guide.!
!
Assembling Video Playlist: https://www.youtube.com/watch?
v=Akz4jSZyOQc&list=PL2KBIbSMnGOh_Mu7Z_c3bYFIhDCGHZpcL
2
Plum Audio - DSO 150 EuroScope v2.0 - Build Guide!
Deign by Shay Shezifi
10.02.19
Bill Of Materials
Q
Part/Value
Ref
Source
Notes
1
DSO150 Eurorack
panel mk2
Pusherman
1
DSO150 Conversion
Board mk2
Pusherman
1
Original Dso150
(15001K) DIY KIT
Banggood
There’s other places to buy this
kit, but you need pay attention
to:!
1. buy only the original kit of jye
tech version 2017.!
I’ve checked this source and it is
the original kit.
2. buy the DIY Kit and not the
assembled one.
1
L7809CV – 9v Voltage
Regulator (SMD)
IC1
Mouser
Mouser Part: 511-L78M09ABDT-TR!
(or AliExpress/eBay)
1
TL072 SMD - SOIC8
IC2
Mouser!
Tayda
2
Diode 1N5819HW
D1,D2
Mouser!
AliExpress
3
Plum Audio - DSO 150 EuroScope v2.0 - Build Guide!
Deign by Shay Shezifi
10.02.19
1
0.33uF – Tantalum
Capacitor (SMD 0805)
C1
Mouser
Mouser Part: 581-TAJR334K020R
3
0.1uF – Ceramic
Capacitor <25v (SMD
0603/0805)
C2,C3,
C4
Tayda!
Mouser!
AliExpress
2
10uF Electrolytic
Capacitor (SMD 4mm
dia) <25v
Mouser
2
Resistor 4.7R (SMD
1206)
R1, R3
Mouser
1
Resistor 51R (SMD
0603/0805)
R4
Mouser
Tayda
1
Resistor 10M (SMD
0603/0805)
R2
Mouser
Tayda
1
3X1 Male Pin Headers
Tayda
Cut from row of 40 pins
1
Jumper
Tayda
1
10 Pin Eurorack
Power Socket
Tayda
Box Header Type
2
3M - 6mm Standoffs
(Spacers) + 2 3M
Screws
AliExpress
The Nylon/Plastic Type are
better.!
To mount the conversion board
to dso150 main board.
2
3M – 12mm-16mm
Black Screws
AliExpress
To mount the panel to DSO150
mainboard and fix the screen
position.
1
PEC11L Encoder
SW6
(Main
Board)
Mouser
Mouser Part:652-PEC11L4215FS0015
* 30 Detent / 15 PPR
* SLIM Body!
SW6 on DSO150 Main Board.
2
PJ301M-12
“Thonkiconn”
Thonk
2
DPDT (ON-ON) Sub
Miniature Toggle
Switch
SW2,
SW3
Thonk
1
Encoder Knob
Thonk
Recommended - Sifam Large Soft
Encoder Knob – 12mm (D-Shaft)
8
10cm Wrapping Wires
4
Plum Audio - DSO 150 EuroScope v2.0 - Build Guide!
Deign by Shay Shezifi
10.02.19
Phase 1:
Assembling DSO 150 KIT
!
Basically, you need to follow the instructions in the user manual that come with your
DSO150 DIY Kit BUT you need to do only the steps below (and skip the others):
1. In the mainboard (Marked as “Step 1”) You need to solder only the Tact
Switches (Step 6) and desolder (or cut) the power socket.!
solder encoder in place (SW6).!
* DON’T REMOVE R30!!
Assembling Video Part 1: https://youtu.be/Akz4jSZyOQc!
2. In the Analog Board (Marked as “Step 2”) You need to solder only the
Resistors (Step 1), Capacitors (Steps 2 & 4) and the Pin-Header (Step 6).!
Assembling Video Part 2: https://youtu.be/BhblcA2ikeY
!
!
5
Plum Audio - DSO 150 EuroScope v2.0 - Build Guide!
Deign by Shay Shezifi
10.02.19
Phase 2:
Assembling Conversion Board!
Assembling Video Part 3: https://youtu.be/UtAiYVECAHI!
1. Solder all conversion board components (Regulator, Capacitors, Resistors,
Opamp, Diodes, Power Header, 3 Pin headers), Short with jumper 2 top pins.!
!
!
!
!
!
!
!
!
!
!
!
6
Plum Audio - DSO 150 EuroScope v2.0 - Build Guide!
Deign by Shay Shezifi
10.02.19
2. Put in place interface parts (do not solder them yet)!
- Thonkiconns!
- Toggle Switches (SW2, SW3)!
!
!
3. Connect the board to power source and check for 9v (+/- 10%) at J2!
!
!
7
Plum Audio - DSO 150 EuroScope v2.0 - Build Guide!
Deign by Shay Shezifi
10.02.19
!
Phase 3:
Assembling all together!
Assembling Video Part 4: https://youtu.be/F8vCOfcVhDU
1. Wiring!!
W1 – 6 Wires to SW1 @ DSO 150 analog board, from left to right: !
- 2 wires of AC !
- 2 Wires of DC !
- 2 Wires for switches signal output, You do not need to wire the GND.!
!
W2 – The square pad need to be wired to the signal input, It’s the lower hole of J1
(BNC Connector).!
!
The round pad Need to be wired to test signal tone (J8 @ DSO 150 Main Board).!
2. Mount the conversion board to the DSO150 mainboard with 2 3M 6mm
Standoffs spacers, Do Not forget to put in place the pin headers (J2), If
you need to expand the holes in the DSO150 mainboard you can rotate in
them a sharp knife or scissors.!
!
!
!
!
!
!
!
!
!
!
8
Plum Audio - DSO 150 EuroScope v2.0 - Build Guide!
Deign by Shay Shezifi
10.02.19
3. Solder J2 pin headers on both boards!
!
!
!
!
!
4. Before you mount the panel It’s good time to adjust trimmers C3 and C5 (Step
5 @ DSO 150 user manual). !
The test signal tone is normalised to the input jack if the jumper set to “Test
Tone”, so you don’t need to plug anything to the audio input for calibration,
just connect your module to a power supply and follow the DSO 150 manual
calibrations instructions (after calibration you can move the jumper to bottom
position).
!
!
!
!
!
!
!
!
!
!
!
9
Plum Audio - DSO 150 EuroScope v2.0 - Build Guide!
Deign by Shay Shezifi
10.02.19
!
5. Mount the panel to DSO150’s Mainboard with two 3M 12mm-16mm!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
6. Solder The Interface parts:!
- Thonkiconn (J3)!
- Toggle Switches (SW2, SW3)!
!
!
!
Table of contents
Other JYE Tech Measuring Instrument manuals
