JYEBAO SMA3200PA-0085/4*f User manual

This part number complies with RoHS.
Notice: JYEBAO reserves the right to make modications deemed appropriate.
SMA3200PA-0085/4*f SMA Plug Phase Adjustable
Weight:
Suitable Cables:
Parts Material Plating (Micro-inch)
Retainer Ring Beryllium Copper Tin-Zinc-Copper-Alloy 100 Over Copper 50
Gasket Silicon
Hex Nut Brass Tin-Zinc-Copper-Alloy 100 Over Copper 50
Insulator Teon
Collet Body Beryllium Copper Gold 4 Over Nickel-Phosphorous Alloy 80 Over Copper 20
Adjustment Nut Brass Tin-Zinc-Copper-Alloy 100 Over Copper 50
Contact Pin Beryllium Copper Gold 4 Over Nickel-Phosphorous Alloy 80 Over Copper 20
Body Brass Tin-Zinc-Copper-Alloy 100 Over Copper 50
Solder Barrel Brass Tin-Zinc-Copper-Alloy 100 Over Copper 50
Coupling Nut Brass Tin-Zinc-Copper-Alloy 100 Over Copper 50
8 HEX
30.3
Ø2.3
3.5
(1.193)
(.315 HEX)
(Ø.091)
(Ø.138)
Typical VSWR
Part Number 1~4Ghz 5~11Ghz 12~18Ghz
SMA3200PA-0085/4*f 1.1 1.15 2.35
Typical PHASE (DEGREES)
Part Number 1Ghz 2Ghz 3Ghz 4Ghz 5Ghz 6Ghz 7Ghz 8Ghz 9Ghz
SMA3200PA-0085/4*f
4º 8º 12º 16º 20º 24º 28º 32º 36º
10Ghz 11Ghz 12Ghz 13Ghz 14Ghz 15Ghz 16Ghz 17Ghz 18Ghz
40º 44º 48º 52º 56º 60º 64º 68º 72º
50Ω

This part number complies with RoHS.
Notice: JYEBAO reserves the right to make modications deemed appropriate.
PHASE TRIMMER INSTRUCTION
SMA3200PA-0085/4*f JYE BAO CO., LTD.
DIAGRAM ASSEMBLY INSTRUCTION
Step 1: STRIP AS SHOWN .
Step 2: INSERT PREPARED CABLE INTO CONNECTOR
BODY " A " AND USE SOLDERING FIXTURE
" ST-008 " , INSERT TOOL " ST-009 " AND LOCATOR
TOOL " ST-011 " TO FIX THE CONNECTOR.
SOLDER IN " X ".
A
BODY
3.3
[0.130]
XST-011
ST-008
ST-009 A

This part number complies with RoHS.
Notice: JYEBAO reserves the right to make modications deemed appropriate.
PHASE TRIMMER INSTRUCTION
SMA3200PA-0085/4*f JYE BAO CO., LTD.
DIAGRAM ASSEMBLY INSTRUCTION
Step 1: LOOSEN NUT1 BEFORE ADJUSTING PHASE.
USE SPANNER SIZE 8MM. (JYEBAO P/N: 8.0-9.0)
Step 2: LOOSEN NUT2 BEFORE ADJUSTING PHASE.
USE SPANNER SIZE 8MM. (JYEBAO P/N: 8.0-9.0)
Step 3: ADJUST TO THE REQUIRED PHASE: KEEP
BODY1 IN A FIXED POSITION AND ADJUST
PHASE BY MANUALLY TURNING BODY2.
Step 4: TIGHTEN NUT2 AFTER ADJUSTING PHASE.
USE SPANNER SIZE 8MM. (JYEBAO P/N: 8.0-9.0)
Step 5: TIGHTEN NUT1 AFTER ADJUSTING PHASE.
USE SPANNER SIZE 8MM. (JYEBAO P/N: 8.0-9.0)
NUT1
NUT2
BODY2BODY1
NUT2
NUT1