Küppersbusch EKS 604.2 User manual

BEDIENUNGSANWEISUNG
mit Montageanweisungen
Instructions for use and installation instructions
Instructions d’utilisation et avis de montage
Gebruiksaanwijzing en montagehandleiding
Istruzioni di uso e di montaggio
Instrucciones de uso y de montaje
Instruções de uso e de montagem
Ðtv³wuÒ xvÒvÒ ÊËw Ò´ÎËxÑÐÌгvÒvÒ
Bruksanvisning i monteringanvisningar
EKS / EGS
241068 L21

EKS/EGS 9
Conditions of guarantee
The conditions o guarantee applicable or this product are subject to those
published by the representative in the relevant country. Details regarding same
may be obtained rom the dealer rom whom the appliance was purchased.
For claims under guarantee the sales receipt must be produced.
For your information
Please read the instructions in this booklet care ully as it contains important
in ormation concerning the sa ety, the installation, the use and the mainte-
nance o your appliance.
The appliance should only be used or cooking in the household.
Keep the operation instructions in a sa e place.
Notes on disposal
Disposing of the packaging
The transport packaging consists o the ollowing materials: Corrugated card-
board, cardboard, styro oam (CFC- ree), Polyethylen- oil.
Do not put these materials in the household rubbish, but ask your local au-
thority to give you the adress o the most convenient collection point.
What to do if you happen to have an old appliance
Old appliances contain many materials which can be recycled. For this reason
you should not simply put your old appliance on the rubbish tip, but ask your
local authority how it might be recycled.
Contents
Your appliance at a glance . . . . . . . . . . . . . . . . . . . . . . . 10
Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
or connecting up and unctioning
or the cooking sur ace
Before first use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Use of the cooking zones . . . . . . . . . . . . . . . . . . . . . . . . 11
Switching the cooking zones on and o
Dual circuit cooking zone
Heating indicators
Some instructions on cookware
What to do if there is a fault . . . . . . . . . . . . . . . . . . . . . . 12
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Please note
Hints on installation
Installation o glass-ceramic hob units
Elektrischer Anschluß

10 EKS/EGS
Your appliance at a glance
1 Cooking/grilling zone
temperature settings
2 Dual circuit cooking zone
3 Normal cooking zone
4 Grilling zone
5 Heating indicators
or cooking zones
6Roasting zone

EKS/EGS 11
Safety instructions
or connecting up and unctioning
■ WARNING: The application must be earthed!
■ The mains connection, maintenance and repair jobs should only be carried
out by an authorised technician in accordance with the applicable sa ety
standards. Work which has been improperly carried out can endanger your
sa ety.
■ The sur aces o heating- and cooking zones become hot during operation.
There ore: Always keep children away.
or the cooking sur ace
■ Overheated ats and oils may spontaneously ignite. You should there ore
cook ood involving the use o ats and oils, e.g. chipped potatoes, only un-
der supervision. Never extinguish ats or oils with water! Place a lid on the
pan, switch o the cooking zone and take the pan o the hot cooking zone.
■ I cracks, ractures, or any other de ects appear in your glass-ceramic cook-
ing area, do not use your appliance. Unplug or otherwise disconnect your
appliance rom the mains supply and call our service centre.
■ Be care ul when working with additional appliances! The connection leads
must not come into contact with the hot cooking zones.
■ The glass ceramic hob should not be used as a storage area.
■ Do not place combustible or in lammable objects upon the cooking top
which might be dangerous in case o unintentional switching on.
■ Do not place any in lammable or combustible items on the hob since there
is a risk o burns or damage i the hob is switched on unintentionally.
■ Never use the cooking zones without cookware.
Never use the appliance to heat rooms!
■ Never put aluminium oil or plastic on top o the cooking zones. Substances
that melt, or example plastic, oils and especially sugar and ood with a
high sugar content are to be kept away rom the hot cooking zone. In order
to avoid damaging, sugar, while still hot, should immediately be scraped o
the cooking area with a scraper.
■ Avoid repeated burning o stains and boiling over.
■ Chalk deposits may damage the cooking area.
■ Please read through the cleaning and care instructions.
Before first use
■ Remove excess materials and packaging.
■ Be ore preparing ood or the irst time, clean the glass ceramic cooking
area with a damp cloth and a little detergent.
■ The cooking area is insensitive to temperatures shocks (cold and hot) and
also extremely robust.
■ Avoid dropping sharp objects onto the cooking area.
Pointed objects alling onto your cooking area might break it.
■ When switching on the cooking zones you might hear a buzzing noise com-
ing rom the heating. This is due to technical reasons and does not in luence
quality or unctioning o your cooking area.
Use of the cooking zones
Read the safety instructions!
Switching the cooking zones on and o
Each cooking zone has its own control. The symbols next to the controls show
to which cooking zone the respective control buttons belong. Always turn the
control buttons anti-clockwise.
Nine cooking settings are marked on the cooking zone controls, but you can
also choose iner intermediate settings. As ar as possible, start cooking at the
highest setting and continue at a smaller setting.
Dual circuit cooking zone
As a standard rule, the smaller cooking zone diameter is heated.
Change the control to the outer cooking zone circuit or rying pans or larger
saucepans.
Turn the cooking zone
control to the le t as ar
as it will go.
Then set it to the re-
quired cooking setting.
Control to "0":
Returns to the smaller di-
ameter.
Heating indicators (1)
The indicators are on or as long as the cooking zones are still very hot –,
even a ter the cooking zones have been switched o .
Caution! The indicator can be de ect (de ect light bulb). You will not not be
warned when the cooking zones are hot. Have the light bulb replaced imme-
diately.
Setting Suitable or
0Switching o
1-3 Heating, Warming,
Creeing, De rosting
4-5 Steaming, Poaching,
Boiling
6-8 Roasting, Deep- rying
9Heating large quantities

12 EKS/EGS
Some instructions on cookware
Only use pans with even and flat bottoms.
Uneven pan bottoms prolong the boost times and increase the power require-
ment. Rough pan bottoms scratch the glass-ceramic area when shi ted about.
When using ireproo glass or porcelain cookware, please ollow the manu ac-
turers instructions.
Choose a pan with a diameter at least as large as the cooking zone.
You will thereby save energy and cooking time. You will also avoid overheating
o the cooking area.
Wherever possible, place a lid on the pan.
You will save a lot o energy by cooking in a closed pan. Liquids and oods
will only boil over i the temperature is too high. For the cooking zones, you
can precisely set the temperature required. With a little practice, you will read-
ily make the correct choice o cooking settings so that nothing boils over even
when a lid is in place.
Cleaning and care
[Never clean the glass ceramic hob with a steam cleaner or similar ap-
pliance!
■ Never use sharp or abrasive agents!
It is su icient to clean with a damp
cloth and a little washing-up liquid
a ter usage. Wipe dry.
■ Incrustation due to boilied over oods
are best preso tened with a wet
cloth. Then remove them with a glass
scraper. Sugar and melted plastic
should be removed while the cooking
area is still hot.
■ Clean the glass-ceramic cooking area a ter every use.
■ Heavy soiling can be cleaned with a cleanser and enough water. Wipe dry
with a cloth.
■ Care or your glass-ceramic cooking area once a week. Regular care builds
up a protective layer and also eases day to day cleaning. Please ollow the
instructions o the cleaner or cleanser manu acturer concerned.
■ For EGS models only:
Please clean your grill regularly, but do not use any cleaning agents which
contain silicone. These will leave a ilm on the grill sur ace which could be
absorbed by the ood upon next use. For this reason it is essential that you
closely observe the cleaning product manu acturer’s instructions.
Even heavy soiling can be cleaned with a cleanser and enough water. A -
terwards always wipe dry with a cloth. Your grill will shine i you then treat
it with a little lemon juice or vinegar.
What to do if there is a fault
Unplug the appliance befor repair!
Check care ully to make sure that the ault is not due to misoperation. You
can recti y many aults yoursel .
Important note:
Repairs should only be carried out by an authorised technician!
Even during the guarantee period repairs will not be ree o charge i due to
incorrect operation or to non-adherence to our instructions given under "What
to do i there is a ault".
You should always give the data on the rating plate to your service centre in
case you have enquiries or want to order spare parts. The rating plate is lo-
cated underneath the hob.
Fault Cause Remedy
Thermal indicator o
cooking zone has
ailed.
Lamp is de ective. Call service centre. Risk o
burning, since no warning o
high temperatures.
Not possible to
switch o cooking
area.
Failure o electronic
component.
Switch o cooker use in use-
box,
Call service centre.
Cooking area does
not heat.
Fuse is de ective. Check or replace cooker use in
use box.
Cooking zone control
button has not been
switched on.
Set the cooking zone control
button.
Control button or
cooking zone de ect.
Call service centre.
Inner circuit o the
dual-circuit zone is
de ective.
Do not operate the unctioning
outer circle.
Immediately call service centre.

EKS/EGS 13
Panel (partition)
ob unit
It must not be possible to remove the panel without
using tools!

14 EKS/EGS
Installation instructions
Please note
KÜPPERSBUSCH built-in hob units may be combined only with KÜPPERS-
BUSCH built-in ovens with tangencial cooling an.
Exception: model series EGS. The use o any other make o hob unit shall ex-
empt Küppersbusch rom all liability. Failure to observe this requirement
will invalidate all granted certificates and labels of approval!
Hints on installation
■ It is absolutely essential that the worktop is aligned horizontally and that a
clean cut is made into it!
■ The ront, rear and lateral clearances around the hob unit must be main-
tained in accordance with the dimensional drawing.
A corner moulding o solid wood may be itted to the worktop at the back
o the hob unit provided that the minimum clearances are maintained.
For practical reasons the lateral clearance between the hob unit and an ad-
jacent tall cupboard unit must measure at least 300 mm.
■ Make sure that there is su icient clearance underneath the cut-out. Any ur-
niture battens must be cut away to leave an area which is at least the same
size as the cut-out itsel .
■ Make a point o ensuring that the plastic laminate or wood veneer on your
urniture surround has been applied by means o a heat-resistant adhesive
(100 °C).
■ Any cooker hoods or wall cupboards must have a vertical clearance o at
least 650 mm rom the hob unit.
It will be expedient to seal built-in sinks and other built-in appliances in the
worktop in the same way (protection against ingress o water).
Prior to installation and a ter removal or repair, examine the gasket or pos-
sible damage. The gasket must provide per ect contact on all our sides. Re-
place it i necessary.
In the case o ceramic-tiled worktops it is necessary to provide an additional
seal with the aid o a permanently elastic sealing compound. Such sealing
compound can be purchased as Küppersbusch spare part No. 53 55 69.
– Clean the sur aces to be sealed in accordance with the manu acturer's
instructions on the cartridge. Apply the compound in a continuous strip,
pressing it irmly against the gap to be sealed.
– Cut away any surplus sealing compound with a sharp kni e and clean the
sealed joint with water.
Installation o glass-ceramic hob units
Using clips makes it easier and quicker or you to install these units. You can
carry out the complete installation work rom above.
■ Always li t the cooking sur ace by holding it at the sides. Do not li t it by
the ront bar.
■ Be extremely care ul when installing! Do not place or drop any sharp or
pointed tools (screwdrivers etc.) on the glass sur ace!
■ The glass-ceramic cooking area must have a level and lush bearing. Any
distortion may lead to racture o the glass panel.
– First o all make a clean cut into the worktop.
– Make sure that the gasket is properly seated. I the worktop sur ace is un-
even (tiles etc.), remove the gasket strip and seal with a heat resistant seal-
ing compound.
– Then insert the clips into the worktop cut-out as shown in the igures on
the previous page, observing the clearances indicated. It is not necessary
to adjust the height due to the horizontal stop motion device.
– Now position the cooking sur ace on the le t as shown in igure, align it (2)
and clip it in (3).
I the worktop cut-out should be a little too
large, it is possible to increase the prelim-
inary spring tension o the clips by screw-
ing them down.
You only require the enclosed tension el-
ements S i you are itting the hob unit into
worktops made o granite, marble or sim-
ilar materials.
Elektrischer Anschluß
■ The built-in cooking area must be connected to the mains supply by
a qualified electrician who is authorized to carry out such work.
■ Both legal wiring regulations and the requirements o your local electricity
supply board must be ully complied with.
■ Sa eguard the appliance by means o line-protecting switches, uses or con-
tactors with at least 3 mm contact opening width.
■ When connecting and repairing the appliance disconnect it rom the elec-
tricity supply with one o these devices.
■ It must not be possible to touch nonconducting parts when the appliance is
installed.
■ The earthed conductor lead must be su iciently long so that, in the event
o ailure o the strain relie , it is not subjected to strain until a ter the live
wires o the connection cable.
■ Any super luous cable must be removed rom the installation area beneath
the appliance.
EKS 804.2, 604.2, 600.0 Permanent connection by means o an oven
connection socket.
Connection diagram is depicted on the underside o the appliance,
suitable or the various types o mains.
Connection data Permanent connection 400 V 3 N
~
50 Hz
(AC 230 V in UK)
Voltage o heating element: 230 V
400 V 3 N ~ sa ety curren 16 A
400 V 2 N ~ sa ety curren 20 A
230 V 1 N ~ sa ety curren 25 A
230 V 3 ~ sa ety curren 16 A
Connection cable Use H 05 RR-F or H 07 RN-F.
The cable must be no shorter than 2 m.
EKS 304.1, EGS 304.0 Connection by means o a shock-proo plug.
Granite