Küppersbusch EKD 10650.0E-84 User manual

EKD 10650.0E-84
Bedienungsanleitung
Instructions Booklet
Mode d’emploi
Libretto Istruzioni
Gebruiksaanwijzing
Manual de instrucciones
Manual de instruções
NL
IT
FR
GB
DE
ES
Εγχειρίδιο
οδηγιών
PT
GR

14GB
CONTENTS
Dear Customer,
If you follow the recommendations
contained in this Instruction Manual,
your appliance will give you constant
high performance and will remain
efficient for many years to come.
RECOMMENDATIONSAND SUGGESTIONS 15
CHARACTERISTICS 16
INSTALLATION 18
USE 21
MAINTENANCE 22

15GB
650 mm min.
RECOMMENDATIONS AND SUGGESTIONS
INSTALLATION
• The manufacturer will not be held liable for any damages resulting
from incorrect or improper installation.
• The minimum safety distance between the cooker top and the
extractor hood is 650 mm.
• Check that the mains voltage corresponds to that indicated on the
rating plate fixed to the inside of the hood.
• For Class I appliances, check that the domestic power supply
guarantees adequate earthing.
Connect the extractor to the exhaust flue through a pipe of
minimum diameter 120 mm. The route of the flue must be as short
as possible.
• Do not connect the extractor hood to exhaust ducts carrying
combustion fumes (boilers, fireplaces, etc.).
• Iftheextractorisusedinconjunctionwithnon-electricalappliances
(e.g. gas burning appliances), a sufficient degree of aeration must
be guaranteed in the room in order to prevent the backflow of
exhaust gas. The kitchen must have an opening communicating
directly with the open air in order to guarantee the entry of clean
air.
USE
• The extractor hood has been designed exclusively for domestic
use to eliminate kitchen smells.
• Never use the hood for purposes other than for which it has ben
designed.
• Never leave high naked flames under the hood when it is in
operation.
• Adjust the flame intensity to direct it onto the bottom of the pan
only, making sure that it does not engulf the sides.
• Deep fat fryers must be continuously monitored during use:
overheated oil can burst into flames.
• The hood should not be used by children or persons not instructed
in its correct use.
MAINTENANCE
• Switch off or unplug the appliance from the mains supply before
carrying out any maintenance work.
• Clean and/or replace the Filters after the specified time period.
• Clean the hood using a damp cloth and a neutral liquid detergent.

16GB
CHARACTERISTICS
Dimensions
650 min.
400
905
582
962
1000
74068
min. 820
310 78
max. 1140
493
1414
122

17GB
12a
11
7.1
2.1
2.2
2
1
9
14.1
15
12a
7.2.1
11
12r
12e
Components
Ref. Q.ty Product Components
11 Hood Body, complete with: Controls, Light,
Blower, Filters
21 Telescopic Chimney comprising:
2.1 1 Upper Section
2.2 1 Lower Section
91 Reducer Flange ø 150-120 mm
14.1 2 Air Outlet Connection Extension
15 1 Air Outlet Connection
Ref. Q.ty Installation Components
7.1 1 Hood Connector Support
7.2.1 2 Upper Chimney Section Fixing Brackets
11 12 Wall Plugs
12a 12 Screws 4,2 x 44,4
12e 6 Screws 2,9 x 9,5
12r 2 Screws 4,2 x 12,7
Q.ty Documentation
1 Instruction Manual

18GB
357 X1÷2
650 min.
7.2.1
7.1
12a
11
11
12a
12r
INSTALLATION
Wall drilling and bracket fixing
Wall marking:
• Draw a horizontal line at 650 mm above the hob.
• Place bracket 7.2.1 on the wall as shown about 1-2 mm from the ceiling or upper limit.
• Mark the wall at the centres of the holes in the bracket.
• Place bracket 7.2.1 on the wall as shown at X mm below the first bracket (X = height of the upper
chimney section supplied).
• Mark the wall at the centres of the holes in the bracket.
• Place the Hood Connector Support 7.1 on the wall as shown at 357 mm above the horizontal
reference line, making sure that the holes used to fix the corner to the wall are equidistant.
• Mark the wall at the centres of the holes in the Support.
• Drill ø 8 mm holes at all the centre points marked.
• Insert the wall plugs 11 in the holes.
• Fix the brackets and the Support using the 12a (4,2 x 44,4) screws supplied.
• Insert the two screws 12r (4,2 x 12,7) supplied in the hood body fixing holes, located on the front
plate of the Hood Connector Support, leaving a gap of 5-6 mm between the Support and the head
of the screw.

19GB
12r
Vr
ø 150
9
ø 120
14.1
15
Mounting the hood body
• Before attaching the hood body, tighten the two
screws Vr located on the hood body mounting
points.
• Hook the hood body onto the screws 12r (4,2 x
12,7).
• Fully tighten support screws 12r (4,2 x 12,7).
• Adjust screws Vr to level the hood body
Connections
DUCTED VERSION AIR EXHAUST SYSTEM
When installing the ducted version, connect the hood to the chimney using either a flexible or rigid
pipe ø 150 or 120 mm, the choice of which is left to the installer.
• To install a ø 120 mm air exhaust connection,
insert the reducer flange 9on the hood body
outlet.
• Fix the pipe in position using sufficient pipe
clamps (not supplied).
• Remove any activated charcoal filters.
RECIRCULATION VERSION AIR OUTLET
• Push fit connection 15 onto the air outlet.
• Insert the connection extension pieces laterally
14.1 in connection 15.
• Make sure that the outlet of the extension pieces
14.1 is horizontally and vertically aligned with
the chimney outlets. Ifthisis notthe case,adjust
the position by either reversing the connection
extension pieces 14.1 or by pushing connector
15 all the way in.
• Ensure that the activated charcoal filters have
been inserted.

20GB
7.2.1
2.1
2.2
2
12e
12e
ELECTRICAL CONNECTION
• Connect the hood to the mains through a two-pole switch
having a contact gap of at least 3 mm.
• Remove the grease filters (see paragraph Maintenance)
being sure that the connector of the feeding cable is cor-
rectly inserted in the socket placed on the side of the fan.
Flueassembly
Upper exhaust flue
• Slightly widen the two sides of the upper flue
and hook them behind the brackets 7.2.1,
making sure that they are well seated.
• Secure the sides to the brackets using the 4
screws 12e (2,9 x 9,5) supplied.
Lower exhaust flue
• Slightlywidenthetwosides of the flue and hook
them between the upper flue and the wall,
making sure that they are well seated.
• Fix the lower part laterally to the hood body
using the 2 screws 12e (2,9 x 9,5) supplied.
12c

21GB
USE
ControlPanel
Thehoodcan be switched on pushing directly onto the requestedspeedwithoutfirstlyhavingto select
0/1button.
KEY LED FUNCTIONS
L0/1Light Turns lighting on and off.
T1 0/1Motor on First speed.
When pressed for about 2 seconds the motor is switched off.
T2 Speed on Second speed.
T3 Speed on Third speed.
T4 Speed Fixed Max. speed
Flashing Intensive speed.
Suitable for the strongest cooking vapours and odours.
The function becomes active when the button is pushed
for about 2 seconds. After 10 minutes of functioning it
turns off automatically. This function can be interrupted
by means of pressing any of the buttons.
S1 Led Fixed Indicates that the Metal grease filters saturation alarm
has been triggered, and the filters need to be washed.
The alarm is triggered after 100 working hours. (Reset;
check the Maintenance-paragraph)
Flashing indicatesthattheactivatedcharcoalodour filter saturation
alarmhasbeentriggered, and the filter has tobereplaced;
the metal grease filters must also be washed. The
activated charcoal odour filter is triggered after 200
working hours. (Activation and Reset; check the
Maintenance-paragraph)
T4T3T2T1L
S1
234
I
F

22GB
MAINTENANCE
Grease filters
CLEANING METAL GREASE FILTERS
Alarm signal reset
• Switch of the lights and extractor motor.
• Press button T3 for at least 3 seconds, until
the leds start to flash.
Cleaning the filters
• The filters are washable and must be
cleaned when led S1 flashes or at least
every 2 months of operation, or more
frequently for particularly heavy usage.
• Remove the filters one at a time by
releasing the fixing hooks.
• Wash the filters, taking care not to bend
them. Allow them to dry before refitting.
• When refitting the filters, make sure that
the handle is visible on the outside.