Küppersbusch IKDEM 976.2GE-84 User manual

Bedienungsanleitung
Instructions Booklet
Mode d’emploi
Libretto Istruzioni
Gebruiksaanwijzing
Manual de instrucciones
Manual de Instruções
NL
IT
FR
GB
DE
IKDEM 976.2GE-84
PT
ES

14GB
CONTENTS
Dear Customer,
If you follow the recommendations contained in this Instruction
Manual, your appliance will give you constant high performan-
ce and will remain efficient for many years to come.
RECOMMENDATIONSANDSUGGESTIONS 15
CHARACTERISTICS 16
INSTALLATION 18
USE 21
MAINTENANCE 22

15GB
650 mm min.
RECOMMENDATIONS AND SUGGESTIONS
INSTALLATION
• The manufacturer will not be held liable for any damages resulting
from incorrect or improper installation.
• The minimum safety distance between the cooker top and the
extractor hood is 650 mm.
• Check that the mains voltage corresponds to that indicated on the
rating plate fixed to the inside of the hood.
• For Class I appliances, check that the domestic power supply
guarantees adequate earthing.
Connect the extractor to the exhaust flue through a pipe of
minimum diameter 120 mm. The route of the flue must be as short
as possible.
• Do not connect the extractor hood to exhaust ducts carrying
combustion fumes (boilers, fireplaces, etc.).
• If the extractor is used in conjunction with non-electrical appliances
(e.g. gas burning appliances), a sufficient degree of aeration must
be guaranteed in the room in order to prevent the backflow of
exhaust gas. The kitchen must have an opening communicating
directly with the open air in order to guarantee the entry of clean
air.
USE
• The extractor hood has been designed exclusively for domestic
use to eliminate kitchen smells.
• Never use the hood for purposes other than for which it has ben
designed.
• Never leave high naked flames under the hood when it is in
operation.
• Adjust the flame intensity to direct it onto the bottom of the pan
only, making sure that it does not engulf the sides.
• Deep fat fryers must be continuously monitored during use:
overheated oil can burst into flames.
• The hood should not be used by children or persons not instructed
in its correct use.
MAINTENANCE
• Switch off or unplug the appliance from the mains supply before
carrying out any maintenance work.
• Clean and/or replace the Filters after the specified time period.
• Clean the hood using a damp cloth and a neutral liquid detergent.

16GB
CHARACTERISTICS
Dimensions
650 min.
732
435
898
72
500
min. 790
max. 1170
790
90
135
500
340

17GB
12f
2
2.1
2.2
11
12h
22
23
21
7.1
1
14.1
15
12g
14
9
25
8
24
12e
12c
7.1a
7.1b
Components
Ref. Q.ty Product Components
11 Hood Body, complete with: Controls, Light,
Blower, Filters
21 Telescopic Chimney comprising:
2.1 1 Upper Section
2.2 1 Lower Section
7.1 1 Telescopic frame complete with extractor,
consisting of:
7.1a 1 Upper frame
7.1b 1 Lower frame
81 Air Outlet Grill
91 Reducer Flange ø 150-120 mm
14 1 Hood BodyAir Outlet Extension Piece
consisting of two Half Shells
14.1 1 Air Outlet Connection Extension
15 1 Air Outlet Connection
24 1 Junction box
25 2 Pipe clamps
Ref. Q.ty Installation Components
11 4 Wall Plugs ø 10
12c 4 Screws 2,9 x 6,5
12e 4 Screws 2,9 x 9,5
12f 4 Screws M6 x 10
12g 4 Screws M6 x 80
12h 4 Screws 5,2 x 70
21 1 Drilling template
22 4 6.4 mm int. dia washers
23 4 M6 nuts
Q.ty Documentation
1 Instruction Manual

18GB
INSTALLATION
Drilling the Ceiling/shelf and fixing the frame
DRILLING THE CEILING/SHELF
• Use a plumb line to mark the centre of the hob on the ceiling/support shelf.
• Place the drilling template 21 provided on the ceiling/support shelf, making sure that the template is
in the correct position by lining up the axes of the template with those of the hob.
• Mark the centres of the holes in the template.
• Drill the holes at the points marked:
• For concrete ceilings, drill for plugs appropriate to the screw size.
• For hollow brick ceilings with wall thickness of 20 mm: drill ø 10 mm(immediately insert the
Dowels 11 supplied).
• For wooden beam ceilings, drill according to the wood screws used.
• For wooden shelf, drill ø 7 mm.
• For the power supply cable feed, drill ø 10 mm.
• For the air outlet (Ducted Version), drill according to the diameter of the external air exhaust duct
connection.
• Insert two screws of the following type, crossing them and leaving 4-5 mm from the ceiling:
• For concrete ceilings, use the appropriate plugs for the screw size (not provided).
• For Cavity ceiling with inner space, with wall thickness of approx. 20 mm, Screws 12h, supplied.
• For wooden beam ceilings, use 4 wood screws (not provided).
• For wooden shelf, use 4 screws 12g with washers 22 and nuts 23, provided.

19GB
FIXING THE FRAME
• Unfasten the two screws fastening the upper
chimney stack 2.1 to the frame, and remove the
chimney from the upper stack.
If you wish to adjust the height of the frame, proceed
as follows:
• Unfasten the four safety screws located at the
top in the frame separation area. (A)
• Unfasten the eight metric screws joining the two
columns, located at the sides of the frame. (B)
• Adjust the frame to the height required, then
replace all the screws removed as above.
• To guarantee greater stability in the frame, replace
the four safety screws in the last hole available.
• Insert the upper chimney stack from above, and
leave it running free on the frame.
• Lift the frame up, making sure that the index over
the frame plate is turned to the front.
• Fit the frame slots onto the two screws inserted
in the ceiling as above, and turn until reaching
the centre of the adjustment slot.
• Tighten the two screws and fasten the other two
screws provided; before locking the screws
completely, it is possible to adjust the frame by
turning it, making sure that the screws do not
come out of their housing in the adjustment slot.
• The Frame must be securely fastened so as to
support both the weight of the Hood and the stress caused by occasional axial pressure against the
fittedAppliance. After fixing, make sure that the base is stable even when the Frame is subjected to
lateral stress.
• If the Ceiling is not strong enough in the area where the hood is to be fixed, the Installer must
strengthen the area using suitable plates and counterplates anchored to resistant structures.
Connections
DUCTED VERSION AIR EXHAUST SYSTEM
When installing the ducted version, connect the hood to the chimney using either a flexible or rigid
pipe ø 150 or 120 mm, the choice of which is left to the installer.
• To install a ø 120 mm air exhaust connection,
insert the reducer flange 9on the hood body
outlet.
• Fix the pipe using the pipe clamps 25 provided.
• Remove any activated charcoal filters.
9
ø 120
ø 150
A
B
2
1
12

20GB
RECIRCULATION VERSION AIR OUTLET
• Insert reducer flange 9on the extractor outlet.
• Push fit the extension piece 14 onto the flange.
• Push fit connector 15 onto the extension piece.
• Insert extension piece/connector 14.1 laterally on
connector 15, ensuring that the outlet is in line
with the chimney intake.
Flue assembly - Mounting the hood body
• Position the upper chimney stack and fix the top of it to
the frame using 2 of the screws removed as above.
• Insert the lower chimney stack into the frame, holding
it in place with adhesive tape in the area separating the
lower chimney stack from the upper one.
Recirculation version
• Make sure that the outlet of the extension piece 14.1 is
horizontally and vertically aligned with the chimney
outlet.
• If this is not the case, remove the lower Chimney Stack
and adjust the position of Extension 14; replace the
elements as described above.
Before fixing the Hood Canopy to the Frame:
• Remove the grease filters from the hood body;
• Remove any activated charcoal filters.
• From below, use the 4 screws 12f provided to fix the hood
body to the frame.
• Remove the adhesive tape fixed to the lower chimney
stack as above, and rest the lower chimney stack against
the hood canopy.
• For the Recirculation Version, fit the directional grill 8
into the housing provided. Also make sure that it is
properly fitted into connector 15.
12f
8b
15
14.1
14
9

21GB
ELECTRICAL CONNECTION
• Connect the hood to the mains through a two-
pole switch having a contact gap of at least 3
mm.
• Remove the grease filters (see paragraph
Maintenance) being sure that the connector of
the feeding cable is correctly inserted in the socket
placed on the side of the fan.
• Connect the control connector Cmd.
• Connect the lights connector Lux.
• Place the connectors in the junction box 24 and
close it using the 2 screws 12e (2,9 x 9,5)
provided.
• Fix the junction box to the hood body using the
2 screws 12c (2,9 x 6,5) provided.
• For the recirculation version, fit the activated
carbon odour filter.
• Replace the grease filters.
USE
Control Panel
The hood can be switched on pushing directly onto the requested speed without firstly having to
select 0/1 button.
KEY LED FUNCTIONS
L0/1 Light Turns lighting on and off.
T1 0/1 Motor on First speed.
When pressed for about 2 seconds the motor is switched
off.
T2 Speed on Second speed.
T3 Speed on Third speed.
T4 Speed Fixed Max. speed
Flashing Intensive speed.
Suitable for the strongest cooking vapours and odours.
The function becomes active when the button is pushed
for about 2 seconds. After 10 minutes of functioning it
turns off automatically. This function can be interrupted
by means of pressing any of the buttons.
24
12e
Cmd
12c
Lux
234
I
F
L
S1
T1 T2 T3 T4

22GB
S1 Led Fixed Indicates that the Metal grease filters saturation alarm has
been triggered, and the filters need to be washed. The
alarm is triggered after 100 working hours. (Reset; check
the Maintenance-paragraph)
Flashing indicates that the activated charcoal odour filter saturation
alarm has been triggered, and the filter has to be replaced;
the metal grease filters must also be washed. The activated
charcoal odour filter is triggered after 200 working hours.
(Activation and Reset; check the Maintenance-
paragraph)
REMOTE CONTROL (OPTIONAL)
The appliance can be controlled using a remote control
powered by a 1.5V carbon-zinc alkaline batteries of the
standard LR03-AAA type.
• Do not place the remote control near to heat sources.
• Used batteries must be disposed of in the proper
manner.
MAINTENANCE
Greasefilters
CLEANING METAL SELF- SUPPORTING GREASE FILTERS
Alarm signal reset
• Switch off the lights and extractor motor.
• Press button T3 for at least 3 seconds, until the
leds start to flash.
Cleaning the filters
• The filters must be cleaned every 2 months of
operation, or more frequently for particularly
heavy usage, and can be washed in a dishwasher.
• Remove the filters one at a time by pushing them
towards the back of the group and pulling down
at the same time.
• Wash the filters, taking care not to bend them.
Allow them to dry before refitting.
• When refitting the filters, make sure that the
handle is visible on the outside.