Küppersbusch IKD 976.2 User manual

Bedienungsanleitung
Instructions Booklet
Mode d’emploi
Libretto Istruzioni
Gebruiksaanwijzing
Manual de instrucciones
Manual de Instruções
NL
IT
FR
GB
DE
IKD 976.2IKD 976.2
IKD 976.2IKD 976.2
IKD 976.2
IKDEM 976.2IKDEM 976.2
IKDEM 976.2IKDEM 976.2
IKDEM 976.2
PT
ES
Εγχειρίδιοοδηγιών
GR

14GB
CONTENTS
Dear Customer,
If you follow the recommendations contained in this Instruction
Manual, your appliance will give you constant high performan-
ce and will remain efficient for many years to come.
RECOMMENDATIONS AND SUGGESTIONS 15
CHARACTERISTICS 16
INSTALLATION 18
USE 21
MAINTENANCE 22

15GB
650 mm min.
RECOMMENDATIONS AND SUGGESTIONS
INSTALLATION
• The manufacturer will not be held liable for any damages resulting
from incorrect or improper installation.
• The minimum safety distance between the cooker top and the
extractor hood is 650 mm.
• Check that the mains voltage corresponds to that indicated on the
rating plate fixed to the inside of the hood.
• For Class I appliances, check that the domestic power supply
guarantees adequate earthing.
Connect the extractor to the exhaust flue through a pipe of
minimum diameter 120 mm. The route of the flue must be as short
as possible.
• Do not connect the extractor hood to exhaust ducts carrying
combustion fumes (boilers, fireplaces, etc.).
• Iftheextractorisusedinconjunctionwithnon-electricalappliances
(e.g. gas burning appliances), a sufficient degree of aeration must
be guaranteed in the room in order to prevent the backflow of
exhaust gas. The kitchen must have an opening communicating
directly with the open air in order to guarantee the entry of clean
air.
USE
• The extractor hood has been designed exclusively for domestic
use to eliminate kitchen smells.
• Never use the hood for purposes other than for which it has ben
designed.
• Never leave high naked flames under the hood when it is in
operation.
• Adjust the flame intensity to direct it onto the bottom of the pan
only, making sure that it does not engulf the sides.
• Deep fat fryers must be continuously monitored during use:
overheated oil can burst into flames.
• The hood should not be used by children or persons not instructed
in its correct use.
MAINTENANCE
• Switch off or unplug the appliance from the mains supply before
carrying out any maintenance work.
• Clean and/or replace the Filters after the specified time period.
• Clean the hood using a damp cloth and a neutral liquid detergent.

16GB
CHARACTERISTICS
Dimensions
650 min.
732
435
898
72
500
min. 790
max. 1170
790
90
135
500
340

17GB
12f
2
2.1
2.2
11
12h
22
23
21
7.1
1
14.1
15
12g
14
9
25
8
24
12e
12c
7.1a
7.1b
Components
Ref. Q.ty Product Components
11 Hood Body, complete with: Controls, Light,
Blower, Filters
21 Telescopic Chimney comprising:
2.1 1 Upper Section
2.2 1 Lower Section
7.1 1 Telescopic frame complete with extractor,
consisting of:
7.1a 1 Upper frame
7.1b 1 Lower frame
81 Air Outlet Grill
91 Reducer Flange ø 150-120 mm
14 1 Hood BodyAir Outlet Extension Piece
consisting of two Half Shells
14.1 1 Air Outlet Connection Extension
15 1 Air Outlet Connection
24 1 Junction box
25 2 Pipe clamps
Ref. Q.ty Installation Components
11 4 Wall Plugs ø 10
12c 4 Screws 2,9 x 6,5
12e 2 Screws 2,9 x 9,5
12f 4 Screws M6 x 10
12g 4 Screws M6 x 80
12h 4 Screws 5,2 x 70
21 1 Drilling template
22 4 6.4 mm int. dia washers
23 4 M6 nuts
Q.ty Documentation
1 Instruction Manual

18GB
INSTALLATION
Drilling the Ceiling/shelf and fixing the frame
DRILLING THE CEILING/SHELF
• Use a plumb line to mark the centre of the hob on the ceiling/support shelf.
• Place the drilling template 2121
2121
21 provided on the ceiling/support shelf, making sure that the template
is in the correct position by lining up the axes of the template with those of the hob.
• Mark the centres of the holes in the template.
• Drill the holes at the points marked:
• For concrete ceilings, drill for plugs appropriate to the screw size.
• For hollow brick ceilings with wall thickness of 20 mm: drill ø 10 mm.
• For wooden beam ceilings, drill according to the wood screws used.
• For wooden shelf, drill ø 7 mm.
• For the power supply cable feed, drill ø 10 mm.
• For the air outlet (Ducted Version), drill according to the diameter of the external air exhaust
duct connection.
FIXING THE FRAME
Before fixing, separate the Upper Section 2.12.1
2.12.1
2.1 and
the Lower Section 2.22.2
2.22.2
2.2 from the Frame by
unscrewing the screws 12c12c
12c12c
12c, then separate the two
sections of the frame by unscrewing the 6 side
screws to obtain the Upper frame and Lower fra-
me.

19GB
Upper frameUpper frame
Upper frameUpper frame
Upper frame
• Align the power supply cable feed hole
• Fix the upper frame to the ceiling or shelf using:
• For concrete ceilings, use the appropriate plugs for the screw size (not provided).
• For hollow brick ceilings of wall thickness of approximately 20 mm: use 4 plugs 1111
1111
11 and 4
screws 12h12h
12h12h
12h, provided.
• For wooden beam ceilings, use 4 wood screws (not provided).
• For wooden shelf, use 4 screws 12g12g
12g12g
12g with washers 2222
2222
22 and nuts 2323
2323
23, provided.
Lower frameLower frame
Lower frameLower frame
Lower frame
• Fix the lower frame using the 8 previously removed screws, adjusting the length according to the
installation height (hood body lower fixing surface must be at least 720 mm from the hob).
• For the recirculation version, turn the frame in the direction chosen for the recirculated air outlet.
• The frame mountings must be secure to withstand the weight of the hood and any stresses caused
by the occasional side thrust applied to the device. On completion, check that the base is stable,
even if the frame is subjected to bending.
• In all cases where the ceiling is not strong enough at the suspension point, the installer must
provide strengthening using suitable plates and backing pieces anchored to the structurally sound
parts.
Connections
DUCTED VERSION AIR EXHAUST SYSTEM
When installing the ducted version, connect the hood to the chimney using either a flexible or rigid
pipe ø 150 or 120 mm, the choice of which is left to the installer.
• To install a ø 120 mm air exhaust connection,
insert the reducer flange 99
99
9 on the hood body
outlet.
• Fix the pipe using the pipe clamps 2525
2525
25 provided.
• Remove any activated charcoal filters.
RECIRCULATION VERSION AIR OUTLET
• Insert reducer flange 99
99
9 on the extractor outlet.
• Push fit the extension piece 1414
1414
14 onto the flange.
• Push fit connector 1515
1515
15 onto the extension piece.
• Insert extension piece/connector 14.114.1
14.114.1
14.1 laterally
on connector 1515
1515
15, ensuring that the outlet is in
line with the chimney intake.
9
ø 120
ø 150
15
14.1
14
9

20GB
12f
8b
24
12e
Cmd
12c
Lux
Flue assembly - Mounting the hood body
• Position the upper chimney section and fix the
upper part to the frame using the 2 screws 12c12c
12c12c
12c
provided.
• Fit the lower chimney section onto the frame,
holding it in place until the hood body has been
fixed in place.
RecirRecir
RecirRecir
Recirculation versionculation version
culation versionculation version
culation version
• Make sure that the outlet of the extension piece
14.114.1
14.114.1
14.1 is horizontally and vertically aligned with
the chimney outlet.
• If this is not the case, remove the lower chimney
section and adjust the position by cutting the
hoodbody extension 1414
1414
14 along one of thethinner
section channels denoting the pre-fixed lenghts,
then reassemble as described previously.
Before fixing the hood body to the frame:
• Remove the grease filters from the hood body;
• Remove any activated charcoal filters.
• From below, use the 4 screws 12f12f
12f12f
12f provided to
fix the hood body to the frame.
• For the recirculation version, locate the
directional grill 88
88
8 in its housing. Ensure that it
is inserted correctly in connector 1515
1515
15.
ELECTRICAL CONNECTION
• Connect the hood to the mains through a two-
pole switch having a contact gap of at least 3 mm.
• Connect the control connector CmdCmd
CmdCmd
Cmd.
• Connect the lights connector LuxLux
LuxLux
Lux.
• Place the connectors in the junction box 24 and
close it using the 2 screws 12e (2,9 x 9,5)
provided.
• Fix the junction box to the hood body using the
2 screws 12c (2,9 x 6,5) provided.
• For the recirculation version, fit the activated
carbon odour filter.
• Replace the grease filters.

21GB
USE
Control panel
LL
LL
L Light Switches the lighting system on and off.
S1S1
S1S1
S1 Led Motor running led. Flashes when the grease filters are saturated.
S2S2
S2S2
S2 Led Intensive speed led. Flasheswhentheactivated carbon odour filters are exhausted.
MM
MM
M Motor Switches the extractor motor on and off at low speed. Used to provide a contin-
uos and silent air change in the presence of light cooking vapours.
V1V1
V1V1
V1 Speed Reduces the operating speed.
V2V2
V2V2
V2 Speed Increases the operating speed.
V3V3
V3V3
V3 Intensive Maximum speed, used for eliminating the highest cooking vapour emission.
speed Switches off automatically after 10 minutes operation. Can also be switched off
manually by pressing the button.
LM V3S1 S2V2V1

22GB
MAINTENANCE
Grease filters
CLEANING METAL SELF-SUPPORTING GREASE FILTERS
Alarm signal resetAlarm signal reset
Alarm signal resetAlarm signal reset
Alarm signal reset
• Switch off the lights and extractor motor.
• Press button V2V2
V2V2
V2 for at least 3 seconds, until the
leds start to flash.
Cleaning the filtersCleaning the filters
Cleaning the filtersCleaning the filters
Cleaning the filters
• The filters are washable and must be cleaned
when led S1S1
S1S1
S1 flashes or at least every 2 months
of operation, or more frequently for particularly
heavy usage.
• Remove the filters one at a time by pushing
them towards the back of the group and
pulling down at the same time.
• Wash the filters, taking care not to bend them.
Allow them to dry before refitting.
• When refitting the filters, make sure that the
handle is visible on the outside.