Küppersbusch KD9890.0 Quick setup guide

KD9890.0
BEDIENUNGSANWEISUNG
mit Montageanweisungen
GB
Instructions for use and installation instructions
Instructions d'utilisation et avis de montage
Gebruiksaanwijzingenmontagehandleiding
Istruzioni di uso e di montaggio
Instrucciones de uso y de montaje
Instruções de uso e de montagem
ÏÄÇÃÉÅÓ ÃÉÁ ÔÇÍ ÅÃÊÁÔÁÓÔÁÓÇ ÊÁÉ ÔÇ ×ÑÇÓÇ
F
NL
I
E
P
GR

DerInnentemperaturmesser(undAußentemperaturmesser)mussmiteiner9V-„Transistor”-Batteriebetrieben
werden(nichtinAusstattungenthalten).WennderTemperaturmesserentferntwird,mussbeachtetwerden,dass
dieBatterienvorherherausgenommenwerdenmüssen.DiegebrauchtenBatterienmüssenaufsichereWeise,unter
VerwendungvongeeignetenBehälternentferntwerden.
Dieses Elektrohaushaltsgerät ist entsprechend der EU-Richtlinie 2002/96/CE über Elektro- und Elektronik-
Altgeräte (WEEE) gekennzeichnet. Bitte sorgen Sie dafür, dass das Gerät ordnungsgemäß entsorgt wird, damit
mögliche negative Auswirkungen auf Umwelt und Gesundheit vermieden werden, die bei einer unsachgemäßen
Entsorgung des Altgerätes entstehen könnten. Das Symbol auf dem Produkt bedeutet, dass dieses Gerät nicht
in den normalen Hausmüll gehört, sondern den jeweiligen kommunalen Rücknahmesystemen für Elektro- und
Elektronik-Altgeräte übergeben werden muss. Die Entsorgung muss im Einklang mit den geltenden Umweltrichtlinien
für die Abfallentsorgung erfolgen. Für nähere Informationen über Entsorgung und Recycling dieses Produktes
wenden Sie sich bitte an Ihre kommunalen Einrichtungen (Umweltamt) oder an die Abfallentsorgungsgesellschaft
Ihrer Stadt bzw. an Ihren Händler.
ENGLISH
WARNING
Thedistancebetweenthesupportingsurfaceforthecookingvesselsonthehobandthelowerpartofthehoodmust
be at least 65 cm. If the instructions for installation for the hob specify a greater distance, this has to be taken into
account.
Theaircollectedmustnotbeconveyedintoaductusedtoblow offsmokesfromappliancesfedwithanenergyother
than electricity (central heating systems, thermosiphons, water-heaters, etc.).
Complywiththe official instructionsprovidedby the competentauthoritiesin merit wheninstallingthe disposal duct.
In addition, exhaust air should not be discharged into a wall cavity, unless the cavity is designed for that purpose.
Theroommustbewellaeratedincaseahoodandsomeotherheatequipmentfedwithanenergyotherthanelectricity
(gas, oil, coal heaters, etc) operate at the same time.
Infacttheintakehood,disposingofair,couldcreateavacuumintheroom.Thevacuumshouldnotexceed0,04mbar.
This prevents the gas exhausted by the heat source from being intaken again. It is therefore advisable to ensure
the room contains air taps able to ensure a steady flow of fresh air.
Checkthedatalabelinsidetheappliance;ifthesymbol( )isprinted,readthefollowing:thisappliancehas
such technical particulars that it belongs to class II insulation, therefore it must not be earthed.
The following warning is valid in the United Kingdom only: in case your cable is not furnished with a plug, read the
following instructions; as the colours of the wires in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows: – the wire which is coloured blue must
be connected to the terminal which is marked with the letter N or coloured black; – the wire which is coloured brown
must be connected to the terminal which is marked with the letter L or coloured red. – terminal of a three-pin plug.
Checkthedatalabelinsidetheappliance; ifthesymbol( )isNOTprinted, readthefollowing:ATTENTION:
Thisappliancemustbeearthed.Whenmakingtheelectricalconnections,checkthatthecurrentsockethasaground
connection.
The following warning is valid in the United Kingdom only: in case your cable is not furnished with a plug, read the
following instructions; as the colours of the wires in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:
–thewirewhichiscoloured green and yellowmustbeconnectedtotheterminal in the plug whichismarkedwiththe
letter E or by the earth symbol [ ], or coloured green or green and yellow; – the wire which is coloured blue must
be connected to the terminal which is marked with the letter N or coloured black; – the wire which is coloured brown
must be connected to the terminal which is marked with the letter L or coloured red.
When making the electrical connections, check that the voltage values correspond to those indicated on the data
plate inside the appliance itself. In case your appliance is not furnished with a non separating flexible cable and has
no plug, or has not got any other device ensuring omnipolar disconnection from the electricity main, with a contact
opening distance of at least 3 mm, such separating device ensuring disconnection from the main must be included
in the fixed installation. If your unit features a power lead and plug, position this so the plug is accessible.
Always switch off the electricity supply before carrying out any cleaning or servicing operations on the appliance.
USE
Avoid using materials which could cause spurts of flame (flambées) near the appliance.
Whenfrying,takeparticularcaretopreventoilandgreasefromcatchingfire.Alreadyusedoilisespeciallydangerous
in this respect. Do not use uncovered electric grates.

To avoid possible risks of fire always comply with the indicated instructions when cleaning anti-grease filters and
when removing grease deposits from the appliance.
MAINTENANCE
Thorough servicing guarantees correct and long-lasting operation.
Any fat deposits should be removed from the appliance periodically depending on amount of use (at least every 2
months).Avoidusing abrasiveorcorrosiveproducts.Tocleanpainted appliancesontheoutside,useaclothdipped
inlukewarmwaterandneutraldetergent.Tocleansteel,copperor brass appliances on the outside,itisalwaysbest
touse specific products,following theinstructions on theproducts themselves. Toclean theinside of theappliance,
use a cloth (or brush) dipped in denatured ethyl alcohol.
DESCRIPTION
The hood may be in the filtering or the ducting version.
Filtering version (Fig. 1): The hood aspirates the kitchen air saturated with fumes and odours, purifies it through
the grease filters and charcoal filter and returns clean air into the room. For constant efficiency, the charcoal filter must
be replaced periodically. The charcoal filter is not supplied.
Ductingversion(Fig.2):Thehoodaspiratesthekitchenair saturated with fumes and odours, passes it through the
greasefiltersandexpelsittotheoutsidethroughanoutletpipe.Withthisversionthecharcoalfilterisnotrequired.Decide
fromthe outseton the type of installation(filtering orducting). For greater efficiency, werecommend youinstall the hood
in the ducting version (if possible).
INSTALLATION
ATTENTION:Twopersonsarerequiredforproperinstallation;theunitshouldbeinstalledbyaqualifiedoperator.
Removethegreasefiltersbeforeproceedingwiththeassemblyinstructions.Thiswillmaketheapplianceeasiertohandle.
1. Removal of grease filters: Fig. 3: push the stop towards the rear of the appliance and turn the filter outwards.
INSTALLATIONINDUCTINGVERSION:Beforefixing,theoutletpipeforairevacuationtotheoutsidemustbeinstalled.
Useanoutletpipewith:–minimumindispensablelength;–minimumpossiblebends(maximumangleofbend:90°);–certified
material (according to the State); – an as smooth as possible inside. It is also advisable to avoid any drastic changes
inpipecross-section(recommendeddiameter:150mm).Forairevacuationtotheoutside,followalltheotherinstructions
givenonthe“Warning”chapter.Preparethepowersupplywithinthetelescopicchimney(fortheelectricconnection,follow
all other indications stated on the “Warning” chapter).
2. Fixing to the wall: Draw a line on the wall in vertical line with your hob. Mark the first 2 holes to be drilled in the
wall,respectingthedistancesindicatedinFig.4.Drillthe2holesandfitthescrewanchorsprovided.Asalreadyspecified
on the “Warnings” sheet, bear in mind that the distance between the lower edge of the hood and the hob must be min.
650 mm. Fix the metal bracket (A) to the wall using the 2 holes just drilled (Fig. 5); the screws for fixing the bracket are
provided. Use the 2 cut-out triangles on the bracket to position it exactly along the vertical axis of the hood. Hang the
hood on the bracket (Fig. 6). Adjust the horizontal position moving the hood to the right or left so that it is aligned with
thewallunits.Ifyoualsoneedtoadjustthehoodinheight,operateontheadjustingscrews(B)provided.Whenadjustment
has been completed, without removing the hood, mark the other 4 holes to be drilled (C) in the wall. Remove the hood
and drill the holes marked (8 mm diameter). Then use the 4 screw anchors and the 4 screws provided for final fixing.
3. Mount the plate of the electrical system fixing it with 3 screws and 2 metal washers (Fig. 7).
4. Install the flange in the device air outlet and press slightly (Fig.8).
5. Fixingthetelescopicflues:
- Adjust the width of the support bracket (D) of the telescopic flue by means of the screws (E) as shown in Fig.9; then,
by means of the screw anchors and screws (F) provided, fix the bracket to the ceiling in such a way that it is positioned
along the axis with your hood.
- Connect the air outlet pipe to the air vent of the hood. - Use a flexible pipe and lock it to the air vent of the hood with
a metal hose clamp - Fig. 10 (pipe and clamp are not provided). - For exhaust hoods, turn the upper flue over so that the
air exhaust grid is in the lower section (Fig. 11).
- Plug in the hood. Insert the extension flues setting them on the hood; extend the upper flue to the ceiling and secure
with the 2 screws (H) - Fig. 12.
INSTALLATION IN FILTERING VERSION: Prepare the power supply within the telescopic flues (for the electric
connection, follow all other indications stated on the “Warning” chapter).
Fixingto thewall:forfixingtothewallrefertotheinstructionsfortheductingversion(seepoints2,3),thencontinue
with the instructions below.
Fixingthetelescopicflues:-Adjustthewidthofthesupportbracket(D)ofthetelescopicfluebymeansofthescrews
(E) as shown in Fig. 9. - Then, by means of the screw anchors and screws (F) provided, fix the bracket to the ceiling in
such a way that it is positioned along the axis with your hood. - Mount the flange on the hood in correspondence to the
air outlet point (Fig. 13). – Take the air baffle and fit a flexible pipe to it (125 mm diameter) locking it with a metal hose
clamp (pipe and clamps are not provided). Fit the air baffle to the upper flue (Fig. 14) with 4 screws.
- Connect the flexible pipe to the flange on the air vent (Fig. 15). - Plug in the hood. Insert the extension flues setting

them on the hood; extend the upper flue to the ceiling and secure with the 2 screws H (Fig. 11). - Install the charcoal
filter fitting the two filter clips in their housings (Fig. 16) and turning the filter upward.
OPERATION
DESCRIPTIONOFTHEKEYSANDFUNCTIONS(Fig.17):
The appliance is equipped with a completely automatic system (Advanced Sensor Control) capable to manage
all the functions of your hood. Thanks to the ASC, the air in the kitchen is costantly clean and odour free
without any manual intervention. The advanced sensor catches all sort of vapours, smokes and odours caused
by the cooking process. The ASC also captures an abnormal presence of GAS. To access this function, press
the key “A” (see point 1 of the instructions).
Thehood also featuresnumerousother functionsthatyou can chooseaccording to yourneeds and preferences.
Using the “MENU” key, you can access the selection methods, and pressing the - and + keys you can search
forthefunctionyouwanttoactivate(thefunctionflasheson the display); once you have madeyourselection,activate
it by pressing “ok”. To exit from the Menu, press the “MENU” key again.
To activate/disactivate the hood motor, press the - key (or + key) and select the desired speed.
List of the functions on the Menu :
-MINUTECOUNTER WITHBUZZER:Thehoodisequippedwithaminutecounterthatemitsan acousticsignalwhen
the time has elapsed. To activate this function, see point 3 of the instructions.
- TIMER: The hood is equipped with a device for automatic stop after 5 (or 10) minutes. To activate this function, see
point 4 of the instructions.
-CLOCK:thetimecanbeshownonthedisplay.Toactivatethisfunctionorsetthetime,seepoint5ofthe instructions.
- SENSOR SENSITIVITY: You can adjust the sensitivity of the sensor according to your specific needs. To access
this function, see point 6 of the instructions.
-INSIDETEMPERATUREINDICATION:Theinsidetemperatureoftheroomcanbeshownonthedisplay.Toactivate
this function, see point 7 of the instructions.
-OUTSIDETEMPERATUREINDICATION(optional):Itispossibletohavetheoutsidetemperatureshownonthedisplay.
To activate this function, see point 8 of the instructions.
- GREASE FILTER CLEANING INDICATION: The hood signals when it is time to clean the grease filters. See point 9
of the instructions.
-CHARCOALFILTERREPLACEMENTINDICATION:Thehoodsignalswhenitistimetoreplacethecharcoalfilters(for
appliances in the filtering version). See point 10 of the instructions.
1. Key“A” (ASCfunction) :To activate the sensor function, press key “A”. Withthesensor activated, thehoodswitches
on automatically in the presence of any type of odour, steam, smoke, or heat from the cooking process, and also in the
presence of any anomalous gas leaks in the environment. When the sensor is active, the display shows the symbol .
To disactivate the sensor, press the key A. With the sensor activated, pressing the - key or the + key takes you directly
to the manual function and the symbol is shown.
2. Key : Light On/Off.
3. Minute counter: To activate the counter, press the “MENU” key (the symbol appears on the display), then press
“ok”. The display shows the number 00.00 blinking. Using the - and + keys you can set the desired number of minutes
(from 1 to 99); keeping the - or + key pressed, the number of minutes scrolls rapidly. Press “ok” to confirm, then press
“MENU”toexit.Whentheminuteshaveelapsed,anACOUSTICSIGNALisemittedandtheindicationblinksonthedisplay:
press “ok” to disactivate it (otherwise, it is disactivated automatically after 5 minutes).
To disactivate the counter at any moment, press the “MENU” and “ok” (reset) keys together.
4. Timer: When the timer is activated, the hood stops automatically after 5 minutes (or 10). To activate the timer, press
the “MENU” key and then the - and + keys until the blinking symbol appears on the display; confirm by pressing “ok”.
You can select the timer for 5 or 10 minutes by pressing the - and + keys, and then press “ok” to confirm. To exit from
the menu, press the “MENU” key.
5. Clock: To activate the clock function and set the time, press the “MENU” key and then the - and + keys until the 4
digits appear on the display blinking; set the time using the - and + keys, then confirm with “ok”. To exit from the menu,
press the “MENU” key. To disactivate the clock function, press the “MENU” and “ok” (reset) keys together.
6. Sensor sensitivity: To adjust the sensitivity of the sensor, press the “MENU” key and then the - and + keys until the
symbol blinks on the display. Then press “ok”, select the sensitivity from 1 to 9 using the - and + keys and confirm
with “ok”. To exit from the menu, press the “MENU” key”.
7.Insidetemperature indication: To viewtheinside temperature onthedisplay,press the “MENU”keyandthen the -key
(or+key)untilthedisplayshows“In18°C”orsimilar;thenpress“ok”.Theinsidetemperatureismeasuredbyameasuring
device (included) which can be positioned anywhere in the room.
8. Outside temperature indication (optional): To view the outside temperature on the display, press the “MENU” key and
thenthe-key(or+key)untilthedisplayshows“Out15°C”orsimilar;thenpress“ok”.Theoutsidetemperatureismeasured

by a measuring device (optional) that can be positioned outside the building, protected from water (maximum distance
on a direct line: about 15 m).
9. Grease filter alarm: After approximately 30 hours of operation, the display will show the symbol , indicating that it
is time to clean the grease filters. Once the filters have been cleaned, restart the hour count by pressing the “MENU”
and “ok” (reset) keys at the same time.
10.Charcoal filter alarm:Afterapproximately 120hours of operation,the display willshow the symbol ,indicating that
itistimetoreplacethecharcoalfilters. Oncethefiltershavebeenreplaced, restartthehourcountbypressingthe“MENU”
and “ok” (reset) keys at the same time.
LISTOF SYMBOLS
SPEED (4 speeds + extra-high speed)
AUTOMATICSENSOR
19.38 CLOCK
MINUTECOUNTER
In 18°C INSIDETEMPERATURE
Out 15°C OUTSIDETEMPERATURE
GREASEFILTERCLEAN
CHARCOALFILTERREPLACEMENT
TIMER
ON / OFF
LIGHTS
RESET(COMBINATIONOF KEYS)
MENUSELECTION
CONFIRMATIONKEY
LESS
MORE
Cleaningthegreasefilters:specialattentionmustbegiventothegreasefilterswhichmustbeperiodicallycleaned,
whenever the grease filter alarm trips. For instructions of the filter Alarm, refer to the Controls paragraph. Remove the
filters as shown in para. 1 and wash with neutral detergent.
Replacingthecharcoalfilters:ifthefilteringversionapplianceisused,thecharcoalfilterswillhavetobeperiodically
replacedwhenthecharcoalfilteralarmtrips.ForinstructionsonthefilterAlarm,refertotheControlsparagraph.Removing
the charcoal filter/s: first of all, remove the grease filters; push the catch inwards (Fig. 3) and remove the charcoal filter
from its case (Fig. 16). Reposition a new charcoal filter of the same type inverting the operations.
Lighting: To replace the halogen lamps, open the cover by prising in the slots (Fig. 18). Replace with lamps of
thesametype.WARNING: Do not touch the new lamp withbarehands.
Insidetemperaturemeasuringdevice:Thehoodissuppliedwithadeviceformeasuringtheinsidetemperaturethat
can be positioned anywhere in the room. The temperature measured is shown on the hood control panel display. If this
function is not active, use the controls on the hood as follows: press the “MENU” key, then press the - or + key until

the display shows “In 18°C” or similar; then press “ok”.
Outsidetemperaturemeasuringdevice(optional):Adeviceformeasuringtheoutsidetemperatureisavailableon
request, which can be positioned outside the building, protected from water (maximum distance on a direct line: about
15 m). The temperature found by the device is shown on the hood control panel display. If this function is not active, use
the controls on the hood as follows: press the “MENU” key, then press the - or + key until the display shows “Out 15°C”
or similar; then press “ok”.
Theinside(andoutside)temperaturemeasuringdevicerequiresa9VTransistortyoebattery(notincluded).
Ifthetemperaturemeasuringdeviceiseliminated,rememberthatthebatteriesmustfirstberemoved.Usedbatteries
mustbedisposedofproperly,usingthespecialcontainers.
This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. The symbol on the product indicates that this product may not be treated as household
waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and
electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste
disposal. For more detailed information about treatment, recovery and recycling of this product, please contact
your local city office, your household waste disposal service or the shop where you purchased the product.
FRANCAIS
ATTENTION
La distance minimum entre la surface de support des casseroles sur le plan de cuisson et la partie inférieure de la
hottedoitêtrede 65 cm. Silesconsignes,pour l’installation du plandecuisson,indiquentune plus grandedistance,
il faut en tenir compte.
L'airaspirénedoitpasêtrecanalisédansunconduitquiestutilisépourévacuerlesfuméesproduitespardesappareils
alimentéspar dessources d'énergies autres que l'énergie électrique (installations de chauffagecentral, radiateurs,
chauffe-eau, etc.).
Pour évacuer l'air qui doit être éliminé respectez les prescriptions des autorités compétentes. De plus l'air qui doit
être évacué ne doit pas être déchargé dans une cavité du mur, à moins que cette cavité soit prévue pour ce but.
Prévoyez une aération de la pièce adéquate quand une hotte et des appareils alimentés par une énergie autre que
l'énergie électrique (poêle à gaz, à huile, à charbon etc.) sont utilisés en même temps. En effet, en évacuant l'air,
lahottepourraitcréerunedépressiondanslapièce.Lapressionnégativedelapiècenedoitpasdépasser0,04mbar,
évitant ainsi que la source de chaleur provoque un appel des gaz qui doivent être évacués. Il est donc nécessaire
d'équiper la pièce de prises d'air alimentant un flux d'air frais constant.
Contrôlerlaplaquedes caractéristiques techniques se trouvant à l’intérieurdel’appareil;silesymbole ( )
figure sur la plaque suivre les instructions suivantes: cet appareil est construit pour appartenir à la classe
d’isolation II ; il ne doit donc pas être relié à la terre.
Contrôlerlaplaquedes caractéristiques techniques se trouvant à l’intérieurdel’appareil;silesymbole ( )
NEfigurepassurlaplaquesuivrelesinstructionssuivantes:ATTENTION:cetappareildoitêtrereliéàlaterre.
Lors du raccordement électrique s’assurer que la prise de courant est équipée d’une connexion de mise à la terre.
Lorsduraccordementélectriqueassurez-vousquelesvaleursdetensioncorrespondentàcellesquisontindiquées
sur la plaque des caractéristiques de l’appareil, qui se trouve à l'intérieur de celui-ci. Si votre appareil, n'a pas de
câble flexible qui ne peut pas être séparé ni de prise, ou bien d'autre dispositif qui garantisse le débranchement de
tous les pôles du réseau, avec une distance d'ouverture entre les contacts d'au moins 3 mm, ces dispositifs de
séparation du réseau doivent alors être prévus dans l'installation fixe. Si votre appareil est muni d’un câble
d’alimentation, positionner l’appareil de manière à ce que la fiche soit accessible.
Avant de procéder à une opération d’entretien ou de nettoyage quelconque, débranchez l’appareil.
UTILISATION
Evitez d'utiliser des matériaux qui provoquent des flammes à proximité de l'appareil.
Dans le cas de fritures, faites tout particulièrement attention au danger d’incendie que représentent les huiles et les
corps gras. A cause de son inflammabilité l’huile usagée est particulièrement dangereuse. N'utilisez pas de grils
électriques découverts.
Pour éviter des risques d'incendie possibles suivez les instructions données concernant le nettoyage des filtres à
graisse et sur la façon d'enlever des dépôts éventuels de graisse sur l'appareil.

12
34
5

67
89
10
11

12
13
14
15
16
17
18