Küppersbusch KD 957.1 GE Operation manual

BEDIENUNGSANWEISUNG
mit Montageanweisungen
Instrucciones de Uso y de Montaje
Instructions for use and installation
Instructions d´utilisation e avis de montage
Instruções de uso com indicações para montagem
Istruzioni di uso e di montaggio
Bruks- och monteringsanvisningar
Gebruiksaanwijzing en montagehandleiding
Åã÷åéñéäßïõ ìå ôéò Ïäçãßåó ×ñÞóåùó
KD 957.1 GE
Manual KND.3.qxd 15/10/2002 17:33 Página 1

14
Dear client:
Congratulations on your choice. We are sure
that this modern, functional and practical
appliance, made with top quality materials,
will fully satisfy your needs.
Please read every section of this
INSTRUCTIONS MANUAL before using your
kitchen hood for the first time, to ensure
maximum performance from the appliance
and to avoid breakdowns, which may be
caused by incorrect use, as well as to allow
any minor problems to be solved.
Store this manual, as it will provide useful
information about your kitchen hood at all
times and will also help other people to use it.
•Please be aware of current local
regulations with reference to domestic
electrical fittings and gas eduction.
•Verify that the tension and frequency of the
network match those indicated on the label
located inside the kitchen hood.
•The appliance must be connected to the
network using a break switch with a
universal cut off and minimum contact
separation of 3 mm.
•Once the kitchen hood has been installed,
ensure that the mains cable to the network
is not in contact with any live metal edges.
•Avoid connecting the appliance to
conductors used as exits for fumes
produced by a non-electric energy source,
e.g.: boilers, chimneys, etc.
•If the extractor fan is going to be used
simultaneously with equipment powered by
a non-electric energy source, e.g.: gas
cookers, the room must have sufficient
ventilation.
•Excessive fat accumulation in the kitchen
hood and metal filters is a fire risk and may
also cause dripping, therefore the inside of
the kitchen hood and the metal filters must
be cleaned at least once a month.
•The lower part of the kitchen hood must be
fitted at least 50 cm. over electric hobs and
65 cm. over gas or mixed hobs. FOLLOW
THE MANUFACTURER'S MINIMUM
RECOMMENDATIONS.
•Never leave gas hobs lit if not covered by a
container. The fat accumulated in the filters
may drip or catch fire when the
temperature increases.
•Avoid cooking under the kitchen hood if the
metal filters are not fitted, e.g.: while they
are being cleaned in the dishwasher.
•You must not produce flames under the
kitchen hood.
•Disconnect the appliance before any
interior manipulation, e.g. during cleaning
or maintenance.
•We recommend the use of gloves and to
be extremely careful when cleaning the
kitchen hood's interior.
•Your kitchen hood is designed for domestic
use and only for extraction and purification
of fumes produced during food
preparation. It will be your responsibility if it
is used for other purposes, which may be
dangerous. The manufacturer cannot
accept responsibility for damage caused
by improper use of the appliance.
•For repairs please contact the nearest
KÜPPERSBUSCH Technical Assistance
Service, and always use genuine spare
parts. Repairs or modifications carried out
by unqualified personnel can cause
malfunctions or may damage the
appliance, putting your safety in danger.
Safety Instructions
Manual KND.3.qxd 15/10/2002 17:33 Página 14

15
Index
Page
Description of the appliance 15
Instructions for use 15
Programming timer 15
Cleaning and maintenance 16
Problem solving 16
Sizes and specifications 17
Accessories supplied 18
Installation 18
Active charcoal filters 18
AElectronic programmer control box
with buttons to control speed, light and
power in use indicators.
BMetal filters.
CLamp with two bulbs - 20 W (G-4).
D, E Vertically adjustable tubecovers.
FDecorative part (Not incluided).
Switch on the extractor fan a few minutes
before you start to cook in order to ensure that
a steady air flow has been established before
fumes appear.
Allow the extractor fan to run for several
minutes after you have finished cooking
(between 3 to 5 minutes) in order to expel all
the grease from the outlet duct. This prevents
the return of grease, smoke and smells.
1.- The draft hood will remain on for 10
minutes at the selected level if pressed at
any speed for more than 2 seconds.
To programme a time other than the pre-
selected one (10 minutes):
a).- Press the "Timer" button with the draft
hood turned off.
b).- Select the intake time by pressing the
corresponding button. (See figure).
c).- Press the "Timer" button again.
d).- Press the chosen speed for more than 2
seconds, and the light will begin to flash.
Instructions for use
Description of the appliance
Maximum speed
Timer
Extra fan
Medium speed
Minimum speed
Light
3 2 1
3
2
1
Programming timer
Manual KND.3.qxd 15/10/2002 17:33 Página 15

16
During cleaning and maintenance work,
make sure the safety instructions set out
on page 14 are complied with.
•If your kitchen hood is made from stainless
steel, use proprietary cleaners mentioned
in the product instructions.
•Never use metallic scourers, nor abrasive
or corrosive products.
•Dry the kitchen hood using a cloth that
does not produce fibres.
To remove the filters from their fittings, press
lightly on the locks and then pull them off.
The metal filters can be cleaned by soaking
them in hot water with neutral detergent until
the fat dissolves and then rinsing them under
the tap or using special anti-grease products.
They can also be washed in a dishwasher. In
this case, it is advisable to stack them
vertically to avoid food residues to stick to
them.
Cleaning in a dishwasher with aggressive
detergents or polish may damage the metallic
surface (blackening it), although this will not
affect its fat retention capacity.
Once clean, leave them to dry off and then fit
them onto the kitchen hood.
Proceed as follows:
•Unscrew the lamp cap trimming cover.
•Change the broken/burnt out lamp.
Maximum lamp power is 20 W (G-4).
• Screw in the lamp cap trimming cover.
Cleaning and maintenance
_________________________________________________________
Problem solving
Proceed with the following checks before calling the Technical Service:
Problem Possible cause Solution
The extractor fan does not work. The mains cable is not connected to the
network.
There is no current in the network.
Connect mains cable to the network.
Provide current tothe network.
The kitchen hood does not extract
sufficiently or vibrates. Filters are saturated with fat.
Obstruction in the air exit conduct.
Change or clean the active charcoal and/or metal
filters, as the case may be.
Remove the obstruction.
The lamps do not light up. The lamps are blown.
The lamps are slack.
Change the lamps.
Tighten the lamps.
Cleaning the hood body
Cleaning the metal filters
Changing light bulbs
Manual KND.3.qxd 15/10/2002 17:33 Página 16

17
Sizes and specifications
3 2 1
Tec. Cod. 217324ND
F .Nr**********
MadeinEurope
AC 220 - 240 V 50 Hz
Technical Code
Network Tension
(V) Network Frequency (Hz)
Lights / Motor Power
(W) Motor Volume
217324ND 220-240 50 2x20 / 250 800 m
3
/h
KÜPPERSBUSCH reserves the right to make changes and corrections to its products
as it deems necessary, without altering their basic characteristics.
Manual KND.3.qxd 15/10/2002 17:33 Página 17

18
1150/125 mm reduction.
1 Anti-recoil valve.
2Supports for tubecover.
2Supports hall.
6Wall plugs (Ø8 x 40).
6Long bolts (Ø5 x 45).
4Wall plugs (Ø6 x 30).
4Long bolts (Ø4 x 30).
2Washers (Ø6.4 x Ø18).
2Washers (Ø6.4 x Ø12).
2Screws (Ø3.9 x 13).
4Screws M4 x 12.
2Clips.
Fig. 1 (Page 19)
On installing the kitchen hood make sure
that the Safety Instructions set out on page
14 are complied with.
To obtain optimum performance, the external
duct must not be more than FOUR METRES
LONG, have no more than two 90° angles and
its diameter must be at least Ø120.
1) Using the attached template, trace and drill
the points for fitting the wall plugs onto the wall
(P) (Ø8 x 40) and (J) (Ø6 x 30).
2) Attach the Supports (O) to the wall using the
long bolts (Q) (Ø 5x45) and the support (H)
with the long bolts (I) (Ø 4x30), as in figure 1.
3) Fit the support (O) to the body of the hood
using the long bolts (L) (M4 x 12).
4) Trace the location of the wall plugs (R) (Ø8
x 40), through the inside of the kitchen hood.
5) Take the kitchen hood off.
6) Drill into the wall and fit the wall plugs (R)
(Ø8 x 40).
7) Hang the kitchen hood; tighten the screws
(M) (M4 x 12) with the washers (A3) (Ø6.4 x
Ø12) and the long bolts (S) (Ø5 x 45) with the
washers (T) (Ø6.4 x Ø18).
8) Adjust the decorative part (U), fixing it softly
to the body of the bell using the screws
provided with the decorative part.
9) Mount the tubecovers, attaching the lower
one to the support (H) as per the detail in figure
1. Lift the upper tubecover up to the desired
height and mark its shape on the wall. Remove
the tubecovers.
10) Fit the clips (F) to the support (C).
11) Centre the support (C) around the shape
marked; trace and drill the fixing points for the
wall plugs (E) (Ø6 x 30). Attach the support (C)
with the long bolts (D) (Ø4 x 30).
12) Fit the part (A) if the inner tube (not
supplied) is Ø150 or (A) + (B) if it is Ø120.
13) Attach the inner tube with a clamp (not
supplied) to (A) or (B) as the case may be.
14) Once the inner tube has been fitted, fit the
lower tubecover around the extractor fan outlet
and attach the upper tubecover with the screws
(G) (Ø3.9 x 13).
15) Adjust the decorative part (U), fixing it
tightly to the body of the bell using the screws
provided with the decorative part.
16) Attach the handles (W) to the decorative
section (U) with the screws (X) and the
washers (Y) supplied with the decorative
section.
When exterior gas extraction is not possible,
then the kitchen hood may be set to purify the
air by recycling it through active charcoal
filters.
The active charcoal filters have an active life of
between three to six months, depending on
the individual conditions of use. These filters
cannot be washed nor regenerated. They must
be replaced once their useful life comes to an
end.
Fig. 2 (Page 19)
1) Put the filters into the lateral draught section
of the motor making the holes in the filters
match up (A) with the pivots (B) of the motor
carcass. Turn as indicated in the diagram.
2) Remove the tubecovers (E). Use the wall
plugs and the previously installed upper
tubecover's support long bolts to fix diffuser
into the wall (C).
3) Connect the diffuser base (C) to the motor
exit via the inner tube (not supplied). Use
clamps (Not supplied). Fit the tubecovers (E)
again.
Active charcoal filters (Optional)
Installation
Accesories supplied
Manual KND.3.qxd 15/10/2002 17:33 Página 18

19
FIG.1
FIG.2
Manual KND.3.qxd 15/10/2002 17:34 Página 19