Kaboodle W-50560 User manual

step 2
Hardware included
A
Tools you will need
To put your kaboodle LED driver together you will need the following tools.
Cordless drill with:
• Number 2 screw tip
• 2mm drill bit Tape
measure
Safety
gearPencil
Things you need to know
10 mm screws x 2
installation guide
p. 1Ver. 1
W-50560
W-50561
Follow these
instructions to
build and attach
your LED Driver
and Distributor
15W & 30W LED Driver (power supply) and distributor
• When using an electrical appliance, basic safety precautions
should always be followed, including the following:
• Always read the instructions first before installation
• Not suitable for outdoor use
• Cut off the power source during the installation
• Don’t bend the cables
• Keep proper ventilation around the unit and don’t stack any
objects on it.
• Keep 10-15 cm of clearance when the device is close to a heat
source
• Check the information on the LED Driver label.
• Please consider the total wattage of all lights being joined
together and select the LED Driver that is greater than this total,
taking into consideration the following:
• 15w = max load 13.5w
• 30w = max load 27w
• 75w = max load 67.5w
• If you have any questions, contact us on:
Australia: 1800 666 078 Monday to Friday between
8:00am and 6:00pm AEST, New Zealand: 0800 522 663
Monday to Friday between 8:00am and 5:00pm NZST
or email: [e-mail].
• Caution: Risk of electrical shock and energy hazard. If product
fails to work, it should be examined by a qualified technician.
Do not remove the case of the LED driver.
• Do not install LED Driver in places with high ambient
temperature or close to fire source.
• Please refer to the specifications about the maximum ambient
temperature limitations.
• Output current and output wattage must not exceed the rated
values on the specifications
• If the LED Driver is damaged, the unit should be replaced.

step 2
LED driver (power supply) and distributor
connecting LED Driver without
IR Control Switch
connecting LED Driver with
IR Control Switch
1. Connect the Voltage LED Driver and the Distributor
2. Connect the LED Panel Cable(s) into the Distributor
3. Connect Driver to power source.
11
22
33
Voltage LED
Driver
Distributor
LED Panel Cables
We offer a dedicated customer service line
for advice or any questions you may have
on kaboodle products.
Call customer service on:
Australia: 1800 666 078 Monday to Friday
between 8.00am and 6.00pm AEST
New Zealand: 0800 522 663 Monday to Friday
between 8.00am and 5.00pm NZST or email:
[e-mail]
step 1
step 2
step 3
step 4
Next, follow the
instructions to fit
your doors and
panels.
Finish off your
Kaboodle Kitchen
by installing your
benchtop.
You’ve finished
adding your
parts and
accessories.
Your Kaboodle
cabinet is now
complete.
Caring for your kaboodle parts and accessories
Looking after your cabinets is really easy and with the right care and maintenance they
will last you for many years. Just follow these simple steps and if you need any more
information you can contact us on 1800 666 078 Monday to Friday between 8:00am
and 6:00pm AEST or email: [e-mail].
Hinges, runners and other parts and accessories should be kept dry at all times.
To keep the mechanisms performing at their best, regularly wipe them with a dry cloth
removing any dust and grime that may build up.
p. 2Ver. 1
W-50560
W-50561
1. Connect the Voltage LED Driver to the
IR Control Switch with cable
2. Connect the IR Control Switch with
cable to the Distributor
3. Connect the Distributor to the LED
Panel cable(s)
4. Connect Voltage LED Driver into the
power source
33
22
11
Voltage
LED Driver
4
IR Control Switch
with cable
Distributor
LED Panel
Cable