Kaboodle W-50563 User manual

step 2
Hardware included
A
Things you need to know
• Always read the instructions first before installation
• Not suitable for outdoor
• Cut off the power source during the installation
• Don’t bend the cables
• Keep proper ventilation around the unit and don’t stack any
object on it.
• Keep 10-15 cm of clearance when the device is close to a heat
source
• Please consider the total wattage of all lights being joined
together and select the LED Driver that is greater than this total,
taking the following into consideration:
• 15w = max load 13.5w
• 30w = max load 27w
• 75w = max load 67.5w
• Never fully load the circuit. Max load = 21.6W
• If you have any questions, contact us on:
Australia: 1800 666 078 Monday to Friday between
8:00am and 6:00pm AEST, New Zealand: 0800 522 663
Monday to Friday between 8:00am and 5:00pm NZST
or email: [e-mail].
Plastic IR Control
addition
installation guide
p. 1Ver. 1
W-50563
Follow these
instructions to
build and attach
your IR Control
Switch with cable
12VDC
IR control switch with cable 12VDC
B
3M Sticker
If you are using an IR Control Switch with
the 15W or 30W Driver & Distributor, the
IR Control Switch can be connected in
between the Driver, and the Distributor.
1. Separate the connector between the
Voltage LED Driver and the distributor
2. Connect IR Control Switch to
connectors at end of the Driver and
the Distributor.
3. Insert extension cable from LED panel
into Distributor
4. Connect Driver to power source
If you are using an IR Control Switch with
the 75W Driver, the Distributor cannot be
separated.
1. Connect IR Control Switch directly to
the Distributor.
2. Insert extension cable from LED panel
into end of IR Control Switch
3. Connect Driver to power source.
11
11
22
22
33
33
Voltage LED
Driver
Voltage LED
Driver
IR Control Switch
with Cable
Distributor
Distributor
4

step 2
IR Control Switch with cable 12VDC
installation options
to drill into a panel:
sensor settings:
to attach under shelf or cabinet:
motion sensor function
light sensor function
To switch functions,
press the bottom for
a short time
Double sided
adhesive tape
If you want to insert the IR switch into a panel,
connect the additional plastic piece to the flat
section to make a round cylinder. Drill a hole as
per below illustration.
NOTE: We only recommend inserting IR Switch
into a panel if the panel thickness is greater
than 20mm
1. The light goes on when moving the
hand over the sensor less then 1sec
2. The light goes off when moving the
hand over the sensor once again for
less than 1sec
To Dim: Hold the finger in the switch
for 3 sec or until the lamp dims.
1. The light goes on when the door is opened
2. The light goes off when the door is closed
Place the sticker onto the flat section of the IR
switch to stick it to a shelf or overhead cabinet.
We offer a dedicated customer service line
for advice or any questions you may have
on kaboodle products.
Call customer service on:
Australia: 1800 666 078 Monday to Friday
between 8.00am and 6.00pm AEST
New Zealand: 0800 522 663 Monday to Friday
between 8.00am and 5.00pm NZST or email:
[e-mail]
step 1
step 2
step 3
step 4
Next, follow the
instructions to fit
your doors and
panels.
Finish off your
Kaboodle Kitchen
by installing your
benchtop.
You’ve finished
adding your
parts and
accessories.
Your Kaboodle
cabinet is now
complete.
Caring for your kaboodle parts and accessories
Looking after your cabinets is really easy and with the right care and maintenance they
will last you for many years. Just follow these simple steps and if you need any more
information you can contact us on 1800 666 078 Monday to Friday between 8:00am
and 6:00pm AEST or email: [e-mail].
Hinges, runners and other parts and accessories should be kept dry at all times.
To keep the mechanisms performing at their best, regularly wipe them with a dry cloth
removing any dust and grime that may build up.
p. 2Ver. 1
W-50563
14.5mm