KALATEL Calibur DVMRe Triplex User manual

C
Ca al li ib bu ur r D DV VM MR Re
e
T Tr ri ip pl le ex x©
Digital Video Multiplexer Recorder
User Manual

0150-0193A 2 Calibur DVMReTriplex
WARNING!
To prevent fire and electric shock, do not expose this product to rain or moisture.
The lightning flash with the arrowhead symbol,
within an equilateral triangle, is intended to alert
the user to the presence of uninsulated
"dangerous voltage" within the products enclosure
that maybe of sufficient magnitude to constitute a
risk of electric shock to persons.
!
The exclamation point, within an equilateral
triangle, is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
CAUTION!
To prevent electric shock, do not remove cover.
No user serviceable components inside. Refer
servicing to qualified service personnel. !
CAUTION! Lithium Battery
Danger of explosion if battery is
incorrectly replaced. Replace only
with the same or equivalent type
recommended by the
manufacturer.
ATTENTION
This product contains a recyclable lithium battery.
It may be illegal to dispose of this battery
improperly under local, state, or federal laws.
Check with your local waste management officials
for disposal and recycling options.
CAUTION!
Electrostatic-Sensitive Device!
Use proper CMOS and MOSFET handing precautions, including approved
grounded wrists straps, etc., to avoid damage to this unit or its internal
components, from electric discharge.
WARNING!
This equipment generates, uses and can radiate radio frequency energy, and if not installed and used
in accordance with the instructions in this manual, may cause interference to radio communications. It
has been tested and found to comply with the limits for a Class A computing device pursuant to subpart
J of part 15 of FCC rules which are designed to provide reasonable protection against such
interference when operated in a commercial environment. This equipment has also been tested and
found to comply with the requirements for a CE Class A device and TUV safety standards.
Operation of this equipment in a residential area may cause interference, in which case the user is
required to take all measures that are necessary, at the user's expense, to correct the interference.

0150-0193A 3 Calibur DVMReTriplex
IMPORTANT INFORMATION
Software and/or firmware is furnished to the purchaser under a license for use on a single system.
Software and/or firmware included with this equipment are the sole proprietary property of, confidential
to, and copyrighted by Kalatel, Corvallis, Oregon, USA. The software/firmware are not to be copied or
disclosed in any manner without the express written consent of Kalatel.
All information and specifications furnished by Kalatel are believed to be accurate and reliable. No
responsibility is assumed by Kalatel for neither its use nor any infringements of rights of third parties
that may result from its use. No license is granted by implication or otherwise under any patent or
patent rights of Kalatel.
The CALIBUR™brand name and product model numbers are the property of Kalatel.
COPYRIGHT, 2002: The contents of this manual may not be copied or reproduced in any manner or
form without the prior written consent of Kalatel.

0150-0193A 4 Calibur DVMReTriplex
Contents
1DVMReTriplex Overview....................................................................................... 6
1.1 Products Featured In This Manual....................................................................................... 6
1.2 Product Description .............................................................................................................. 6
1.3 Passwords.............................................................................................................................. 7
1.4 Unpacking .............................................................................................................................. 8
1.5 Installation Environment ...................................................................................................... 8
1.6 Associated Equipment.......................................................................................................... 8
1.7 The Rear Panel....................................................................................................................... 9
1.8 Power-Up.............................................................................................................................. 13
1.9 Minimum Recommended Menu Setup .............................................................................. 14
2DMVReTriplex Basic Operations ....................................................................... 15
2.1 Principal Operating Modes................................................................................................. 15
2.2 The Front Panel ................................................................................................................... 15
2.3 Live Viewing......................................................................................................................... 16
2.4 Playback ............................................................................................................................... 17
2.5 Recording............................................................................................................................. 19
2.6 Display Options ................................................................................................................... 20
2.7 Active Cameos..................................................................................................................... 20
2.8 Sequencing .......................................................................................................................... 21
2.9 On-screen Indicators .......................................................................................................... 22
2.10 Triplex Mode ........................................................................................................................ 24
3Menu System Overview ...................................................................................... 26
3.1 Menu Notation In This Manual ........................................................................................... 26
3.2 Accessing The Menu System............................................................................................. 26
3.3 Available Menus .................................................................................................................. 26
3.4 Menus In This Manual ......................................................................................................... 27
3.5 Navigating The Menu System ............................................................................................ 27
3.6 Menu Shortcuts ................................................................................................................... 27
3.7 The Main Menu..................................................................................................................... 28
3.8 Time/Date ............................................................................................................................. 28
3.9 Sequencing .......................................................................................................................... 30
3.10 Record.................................................................................................................................. 30
3.11 Alarms.................................................................................................................................. 36
3.12 Macro ................................................................................................................................... 40
3.13 Motion Detection................................................................................................................. 42
3.14 Camera Setup...................................................................................................................... 45
3.15 Archive Setup...................................................................................................................... 47
3.16 Communications................................................................................................................. 48
3.17 Front Panel Lock................................................................................................................. 50

0150-0193A 5 Calibur DVMReTriplex
3.18 Factory Settings .................................................................................................................. 50
3.19 Passwords ........................................................................................................................... 51
3.20 The QuickInstall Menu ........................................................................................................ 52
3.21 The Operator Menu ............................................................................................................. 52
3.22 The SystemView Menu........................................................................................................ 53
4Alarms .................................................................................................................. 56
4.1 Alarm Input........................................................................................................................... 56
4.2 Alarm Output........................................................................................................................ 56
4.3 Alarm Acknowledge ............................................................................................................ 56
4.4 On-screen Displays During Alarms................................................................................... 56
4.5 Alarm Operations During Playback................................................................................... 57
4.6 Alarm History Box ...............................................................................................................58
4.7 Searching For Recorded Alarms ....................................................................................... 58
5Searching............................................................................................................. 59
5.1 Disk Analysis Screen .......................................................................................................... 60
5.2 Motion Search...................................................................................................................... 60
5.3 Search Filters....................................................................................................................... 62
5.4 Search Results..................................................................................................................... 62
6Technical Specifications .................................................................................... 64
7RS232 Event Generation/Text Insertion Protocol .................................................. 66
7.1 Message Structure .............................................................................................................. 66
7.2 Message Type...................................................................................................................... 66
7.3 Event Field ........................................................................................................................... 66
8RS232 Remote Control Protocol ........................................................................... 68
8.1 Front Panel Button Emulation............................................................................................ 68
8.2 Configuration and Status ................................................................................................... 69
9Macro Tables ....................................................................................................... 70
9.1 Macro Functions Table ....................................................................................................... 70
9.2 Scheduled Macro Table ...................................................................................................... 71
10 Warranty and Service......................................................................................... 72
10.1 Factory Service.................................................................................................................... 72
10.2 Warranty and Return Information...................................................................................... 73

0150-0193A 6 Calibur DVMReTriplex
1 DVMReTriplex Overview
1.1 Products Featured In This Manual
DVMRe-4CT: Digital Video Multiplexer Recorder, Four-Channel, Color, Triplex.
DVMRe-10CT: Digital Video Multiplexer Recorder, Ten-Channel, Color, Triplex.
DVMRe-16CT: Digital Video Multiplexer Recorder, Sixteen-Channel, Color, Triplex.
Key To Model Numbers
DVMRe16 C T
1 2 3 4
1. DVMRe:Digital Video Multiplexer Recorder, Ethernet capable.
2. 4, 10, or 16: Maximum number of camera inputs.
3. C: Color.
4. T: Triplex.
1.2 Product Description
The DVMReTriplex is a video multiplexer capable of recording from multiple cameras to an internal
hard drive while simultaneously providing playback. Unlike outdated time-lapse VCRs, the DVMRe
Triplex records high-resolution pictures. Digital recording improves playback quality over VCRs, and
eliminates the hassle of cleaning heads, changing tapes or servicing motors. The unit can also be
programmed to record continuously by overwriting the oldest recorded data. Depending on the setup,
the DVMReTriplex can store from a few hours to more than 3 years of color images.
Programmable search features eliminate time consuming Fast Forwarding or Rewinding of tapes,
searching for critical data. Search for recorded images or events by alarm, time, date, motion, video
loss, camera number and ASCII cash register or ATM text.
Caution! This products primary purpose is to furnish video multiplexing and recording.
Although the unit has alarm handling and motion detection functions, they are considered
secondary features. This unit should not be the only alarm device on site.
Features
• Multiplexer functionality with built-in digital recording.
• Triplex simultaneous recording, playback, and live multiscreen viewing.
• Remote programming and control through the RS232, RS485 and Ethernet ports.
• View live or recorded images remotely using WaveReader software.
• Dual multiscreen monitor displays.
• Video motion detection (intrusion and activity).
• Motion search.
• Record speed selectable per camera.
• Displays include full screen, sequenced, picture-in-picture, and multiscreens.
• Alarm Handling with History Log. Pre- and post alarm recording, selectable per camera.
• Archive onto Calibur DVSeDisk Array, or RAID, DAT, AIT, or CD-Rs.
• PTZ control via ethernet or POTS, using CBR-KB3/J or KTD-405 keypad.
• Covert camera recording (recording without display).
• Daylight savings time change function.

0150-0193A 7 Calibur DVMReTriplex
1.3 Passwords
Passwords are provided to limit access to menus and certain functions. Two levels of password
security are provided:
• Operator: Limited menu access, only Operator and System View menus are available.
• Installer: Complete menu access.
As a security measure, it is recommended that the Operator and Installer passwords be changed after
installation is complete (see section 3.19). Store the passwords in the administrator’s secure files.
Default Passwords
Four-Channel Units
Password
Type
Access
Level Function
Changeable
by user?
Default
Password
Operator Operator Provides access to the Operator
and SystemView menus. Yes Press ‘ENTER’
4 Times
Installer Installer Provides access to all on-screen
menus. Yes 3 4 4 4
Factory
Defaults Installer Resets the multiplexer to the
factory defaults. No 4 1 1 1
Language Installer Provides access to the On-screen
Language menu. No 1 4 1 4
Ethernet
Access
Reset
Installer
Deactivates the ethernet
password, so that the unit may be
accessed by any PC equipped with
WaveReader.
No 1 1 1 1
Ten and Sixteen-Channel Units
Password
Type
Access
Level Function
Changeable
by user?
Default
Password
Operator Operator Provides access to the Operator
and SystemView menus. Yes Press ‘ENTER’
4 Times
Installer Installer Provides access to all on-screen
menus. Yes 3 4 7 7
Factory
Defaults Installer Resets the multiplexer to the
factory defaults. No 8 1 1 1
Language Installer Provides access to the On-screen
Language menu. No 5 4 1 5
Ethernet
Access
Reset
Installer
Deactivates the ethernet
password, so that the unit may be
accessed by any PC equipped with
WaveReader.
No 1 1 1 1

0150-0193A 8 Calibur DVMReTriplex
1.4 Unpacking
Check the package and contents for visible damage. If any components are damaged or missing, do
not attempt to use the unit, contact the supplier immediately. If the unit must be returned, it must be
shipped in the original packing box.
Package Contents
• The DVMReTriplex unit.
• The Alarm Interface Circuit Board (P/N 0090-0077B).
• The User Manual (P/N 0150-0193A).
• A WaveReader Software CD (P/N 0151-0005-25W11).
• The WaveReader Software Manual (P/N 0150-0143I).
• The Archiving Addendum (P/N 0150-0194A).
• Power Supply (P/N 4310-0020)
• Power Cord ( NTSC P/N 4310-0002) (PAL P/N 4310-0001)
1.5 Installation Environment
Power: Ensure that the installation site’s AC power is stable and within the rated voltage of the 12
Volt DC power supply. If the site’s AC power is likely to have spikes or power dips, use power line
conditioning or an Uninterruptable Power Supply (UPS).
Ventilation: Ensure that the location planned for the installation of the unit is well ventilated. Take
note of the locations of the cooling vents in the unit’s enclosure, and ensure that they are not
obstructed.
Temperature: Consider the unit’s operating temperature (0 to 40 °C) and non-condensing humidity
specifications (10% to 80%) before choosing an installation location. Extremes of heat or cold beyond
the specified operating temperature limits may cause the unit to fail. Do not install the unit on top of
other hot equipment. Leave space between rack mounted units.
Moisture: Do not expose the unit to rain or moisture. Moisture can damage the internal components.
Do not install the unit near sources of water.
Chassis: Other equipment may be placed on top of the unit if it weighs less than 35 pounds (16
kilograms).
1.6 Associated Equipment
Associated equipment in a typical security system could contain the following items:
• Two monitors
• A Keyboard (KB3 or KTD405).
• Video cameras: Composite video, 1 volt peak-to-peak.
• Alarm input devices: Pressure sensors, motion detectors, etc.
• Alarm output devices: Buzzers, Sirens, Flashing Lights, etc.
• A PC connected via ethernet cable.
• An external archive device, such as a DVSe, RAID, CD-R, DAT, or AIT drive.
For instructions regarding the connection of the associated security equipment in your system, please
consult the instruction manual of the associated equipment.

0150-0193A 9 Calibur DVMReTriplex
1.7 The Rear Panel
11 12 13 14 15 16123 45678910
1 2 3 4 5 6
7 8 9 10 11 12
B B
SVHS
SCSI
RS-232/1
RS-485/1
RS-485/2 RS-232/2
ETHERNET
10/100
1. Camera Inputs: BNC connector, looping. Auto Terminating.
2. Composite Monitor-A Output: Composite video output with BNC style connector.
3. Y/C Monitor-A Output: Y/C video output with 4-pin mini-DIN style connector.
4. Alarm I/O: For connecting alarm inputs, and alarm output relays.
5. RS485 Port 1 Connector: For connecting to keyboard and other RS485 devices.
6. 10/100 Ethernet Port: For connecting to remote PC via ethernet network.
7. Composite Monitor-B Output: Composite video output with BNC style connector.
8. Y/C Monitor-B Output: Y/C video output with 4-pin mini-DIN style connector.
9. SCSI Port: For connecting SCSI compatible archive devices.
10. RS232 Port 1: For modem connection and external control of the unit.
11. RS485 Port 2 Connector: For connecting to keyboard and other RS485 devices.
12. RS232 Port 2: For Event Generation and ASCII Text insertion.
Camera Inputs
Cable: 75-Ohm Coaxial
Connectors: BNC
Auto Terminating: Yes
Passive Looping: Yes
There are two BNC jacks for each camera. Either
jack can receive a camera signal. The signal is
looped (directly connected to the other jack), making
the camera signal available to other equipment.
The camera input connectors are Auto Terminating.
This means that the input signal will automatically be terminated with 75-Ohms unless a 2nd cable is
connected to the 2nd BNC connector of the same camera input. Make sure there is 75-Ohm
termination at the end of the video line if the signal is looped through the DVMRe Triplex.
Time base correction is performed during digital capture. As a result, cameras do not require
synchronization.
See section 3.14 for information about disabling unused camera jacks in the menu system.
Composite Monitor Output
When connecting directly from the DVMReTriplex to
the monitor, select the 75-Ohm impedance setting on
the monitor.
Cable: 75-Ohm Coaxial
Connectors: BNC
If an additional device is connected to the monitor’s looping output, set the termination of the additional
device as 75-Ohm, and set the termination of the monitor as Hi-Z (High Impedance).

0150-0193A 10 Calibur DVMReTriplex
Y/C Monitor Output
Y/C video output has a 4-pin mini-DIN style
connector. This style of connection is also referred to
as SVHS and S-Video.
Cable: 75-Ohm Coaxial
Connectors: BNC
Alarm I/O Port
The rear panel of the unit is equipped with an Alarm
Port (DB-25 style connector).
Do not attempt to wire directly to the DB-25
connector on the rear panel. DB-25 Connector on Rear Panel
Connect the Alarm PCB (supplied with the unit) to the Alarm Port. Wire all alarm inputs to the Alarm
PCB per the pin out specifications shown below.
Pin 1: Alarm Input 1.
Pin 2: Alarm Input 2.
Pin 3: Alarm Input 3.
Pin 4: Alarm Input 4.
Pin 5: Alarm Input 5.
Pin 6: Alarm Input 6.
Pin 7: Alarm Input 7.
Pin 8: Alarm Input 8.
Pin 9: Alarm Input 9.
Pin 10: Alarm Input 10.
Pin 11: Alarm Input 11.
Pin 12: Alarm Input 12.
Pin 13: Alarm Input 13.
Pin 14: Alarm Input 14.
Pin 15: Alarm Input 15.
Pin 16: Alarm Input 16.
Pin 17: Alarm Output Relay #1.
Pin 18: Ground.
Pin 19: Ground.
Pin 20: Ground.
Pin 21: Alarm Output Relay #1 Common.
Pin 22: Alarm Output Relay #2.
Pin 23: External Alarm Silence and Acknowledge Input.
Pin 25: Alarm Output Relay #2 Common.
NO1A1 A2A14 A15 A16A3 A4 A5 GND GNDGNDA6 NO2 COM1 A7A8A9A10 GNDACKA11VextA12A13 COM2
171214 15 1634518 19196
Signal
PIN
22 21 78910 202311241213 25
Signal
PIN
Alarm PCB
Active alarm inputs vary by DVMRemodel. 4 channel units (4CT) have 4 active alarm inputs. 10
channel units (10CT) have 10 active alarm inputs.
Alarm Input
An alarm condition can be activated by devices such as pressure pads, passive infrared detectors,
door switches, or other similar devices.
See section 3.11 for information about configuring the contacts as Normally Open or Normally Closed
in the menu system.
Normally Open, Zero Potential Relay Contact: Configure in menu as Normally Open.
Normally Closed, Zero Potential Relay Contact: Configure in menu as Normally Closed
TTL Active High: Configure in menu as Normally Closed.
TTL Active Low: Configure in menu as Normally Open.
Open Collector Active On: Configure in menu as Normally Open.
High: 5V (12V Tolerant)
Low: Ground
Inputs: 1 per channel.
Open Collector Active Off: Configure in menu as Normally Closed.